Consolideck DuraSheen Cure-and-Seal ... - PROSOCO, Inc.

Consolideck ® DuraSheen Cure-and-Seal Specification
Specifier Note: The information provided below is intended to guide the Architect in developing
specifications for products manufactured by PROSOCO, Inc. and should not be viewed as a
complete source of information about the product(s). The Architect should always refer to the
Product Data Sheet and MSDS for additional recommendations and for safety information
Specifier Note: Paragraph below is for PART 1 GENERAL, Quality Assurance.
Test Area
Test a minimum 4 ft. by 4 ft. area on each type of masonry. Use the manufacturer’s application
instructions. Let test area protective treatment cure before inspection. Keep test panels available
for comparison throughout the project.
Specifier Note: Paragraphs below are for PART 2 PRODUCTS, Manufacturers and Products.
Manufacturer: PROSOCO, Inc., 3741 Greenway Circle, Lawrence, KS 66046. Phone: (800)
255-4255; Fax: (785) 830-9797. E-mail: CustomerCare@prosoco.com
Product Description
Consolideck® DuraSheen is a non-yellowing curing and sealing compound. Tough and chemical
resistant, DuraSheen is designed for horizontal concrete where a premium, vibrant gloss and
shine are required.
DuraSheen contains no fillers, modifiers or extenders that can cause cure and seals to yellow,
blush or dull out. Independent laboratory tests confirm DuraSheen’s non-yellowing characteristics
outlast and outperform competitive products.
Easily applied DuraSheen quickly forms a hard, glossy, water- and dust-proof clear shield on
concrete. It’s long-lasting, chemical resistant, waterproof, and dust proof. DuraSheen is ideal for
concrete new or old. It makes an excellent base coat for paints or tile and carpet adhesives,
meeting the requirements of the Resilient Tile Institute and the tile adhesion test requirements of
ASTM C 1315.
Technical Data
FORM: Clear liquid
SPECIFIC GRAVITY: 0.77
TOTAL SOLIDS: 32%
WT./GAL.: 7.9 lbs.
FLASH POINT: >100°F (>38°C)
FREEZE POINT: -8°F (-22°C)
VOC CONTENT: Complies with USEPA AIM VOC regulations. Not suitable for states and
districts with more restrictive regulations.
Specifier Note: For Performance Specifications, include test data for Consolideck® DuraSheen.
Performance Test Data6
Federal EPA VOC
ASTM C 1315, Type 1, Class A
ASTM C 156 (Method of Testing)
ASTM C 309, Type 1, Clear
AASHTO M 148, Type 1, Transparent
NOVDOCK 13 YF
TT-C-800A
Asphalt and Vinyl Asbestos Tile Institute

Code of Federal Regulations Title 40; Part 59
Limitations
Will not bond to cementitious adhesives. Test for bondability to new products.
Not for use around pools or fountains.
Will not compensate for structural or surface defects.
Not suitable for sale in states and districts with more restrictive AIM VOC regulations.
Specifier Note: Paragraphs below are for PART 3 EXECUTION, Installation.
Application
Before applying, read “Preparation” and “Safety Information” sections in the Manufacturer’s
Product Data Sheet for Consolideck ® DuraSheen. Do not dilute or alter. Mix well before use.
Curing New Concrete
Apply as soon as surface water has disappeared and slab can support the weight of an
applicator. Apply at 300-400 ft 2 /gal (7-10 m 2 /L). Coverage may vary based on porosity
and texture of surface.
Sealing New & Existing Concrete
Surfaces must be clean, dry and in good repair. On concrete already cured with
DuraSheen, sealing with DuraSheen gives added protection. Apply after 28 days of curing.
On concrete not cured with DuraSheen, apply two coats. Add the second coat four hours
after the first.
Coverage & Drying Times
New concrete
Older concrete
300 ft 2 /gal (7 ft 2 /L)
400-600 ft 2 /gal (7-10 ft 2 /L)
At 80°F (27°C) treated surfaces dry as follows:
To touch
25 minutes
Light foot traffic 4 hours
Normal traffic
overnight
Maximum hardness 7 days