PRODUCTINFORMATIE - BTicino

PRODUCTINFORMATIE
Nieuwe dimmer voor LED, CFL en Halogeen lampen
Ons assortiment dimmers wordt uitgebreid met een universele dimmer voor LED,
Spaar- en Halogeen lampen, de BTF418. Deze zal vanaf januari 2013 leverbaar zijn.
Artikelnummer: BTF418
Brutoprijs: € 155,-
Kortingsgroep: J5
Details:
n Behuizing 4 modules DIN
n Nul-aansluiting noodzakelijk
n Opgenomen vermogen uit bus, maximaal 10mA
NIEUWE
LED-DIMMER
REF.NR. BTF418
Datum: 27-11-2012
Gebruik: In- en extern
Dimbare belastingen:
* 300VA staat bij LED- en spaarlampen ongeveer gelijk aan 200W
Niet alle te leveren lampen zijn getest i.c.m. deze dimmer. Mede door de verschillende
kwaliteiten van de lampen, is het niet mogelijk om op voorhand een goede werking
van alle combinaties te garanderen.
Meer informatie
Voor prijzen en technische specificaties kunt u de Legrand E-Catalogus bekijken
via www.legrandservices.nl. Voor overige vragen kunt u contact opnemen met
onze afdeling Klantenservice via telefoonnummer 0411 65 33 02
of e-mail salessupport@legrandnederland.nl.
Bijlage: Technical Sheet BTF418
1

Dimmer for LED, CFL,
and halogen lamps
F418
1. USE
1
The device is a dimmer for the management of dimmer LEDs, compact
fluorescent lamps (CFL), and energy saving halogen lamps. After
connecting the dimmer to the BUS and the load, it is possible to adjust
the intensity of the light from any appropriately configured control point.
A quick pressure of the local control pushbutton is enough to switch the
load on or off, while an extended pressure will adjust the light intensity.
The dimmer can be used to adjust the load to 100 different light intensity
levels. It is also possible to adjust the ON time, and the minimum level of
the power in dimmer mode.
6
2. Technical data
Power supply from BUS SCS:
27 Vdc
Operating power supply with SCS BUS: 18 – 27 Vdc
Max. absorption:
10 mA
Number of outputs:
1x 0.9 A
Operating temperature: (-5) – (+35) °C
Dissipated power with max. load:
2.5 W (230 Vac)
1.9 W (127 Vac)
Power/Absorption of driven loads:
Dimmer LEDs, compact
fluorescent lamps, and
energy saving lamps
5
4
3
2
230 Vac 200 W
110 – 127 Vac 100 W
3. Standards, Certifications, Marks
• EN 60669-2-1: Switches for household and similar fixed electrical
installations;
• EN 50090-2-2: Home and building electronic systems (HBES);
• EN 50090-2-3: Home and building electronic systems (HBES), general
functional safety;
• EN 50428: Switches for household and similar fixed electrical
installations.
5. Legend
1. Load
2. Configurator socket (only use in My Home system with physical
configuration)
3. BUS
4. ON/OFF key and brightness adjustment
5. Led
• OFF: BUS not present
• ON green: load off
• ON orange: load on
• flashing quickly orange/green: device not configured
• flashing slowly orange/green: device being configured, or load
fault
6. Fuse
4. Dimensional data
Size: 4 DIN modules
BT00594-a- EN 18/06/2012
1/2

F881NA/16
Dimmer for LED, CFL, and halogen lamps
F418
6. ConfiguraTion
When installed in a MY HOME system, the device may be configured in
two ways:
• PHYSICAL CONFIGURATION, by connecting the physical configurators
to their sockets.
• VIRTUAL CONFIGURATION, by connecting the system to the PC using
the Kit or the Web server. The Virtual configurator software must be
installed on the PC.
PHYSICAL CONFIGURATION
The actuator performs all the basic operating modes that can be
configured directly on the control. Moreover further operating modes
with the configurator in position M of the same actuator are listed in the
table below.
Possible function
Configurator in M
Actuator as Slave. Receives a control sent by
SLA
a Master actuator with the same address
Pushbutton (ON monostable) ignores Room
PUL
and General controls
Master Actuator with OFF control delayed
on the corresponding Slave actuator. Only
for point-point control. With the OFF control
1 – 4
the Master actuator deactivates; the Slave
1)
actuator deactivates after the time set with
the configurators has elapsed 1)
1) The ON control activates the Master actuator and the Slave actuator at
the same time. The next OFF control deactivates the Master actuator
and keeps the Slave actuator active for the period of time set with
configurator 1 - 4 connected to M of the Master actuator as indicated
in the table.
Configurator
Time
1 1
2 2
3 3
4 4
MIN
The configurator in this position defines the minimum value of the light
intensity that can be obtained through dimmer adjustment.
Configurator
Minimum light intensity level
None or 0 Default value (*)
1 1 %
2 5 %
3 10 %
4 15 %
5 20 %
6 25 %
7 30%
8 35 %
9 40 %
Note (*): the default value is set to ensure the best performance based on
the configurator in the TY position.
WARNING:
For correct operation of the actuator, set the type of lamp to control
using the configurator in the TY position.
If the lamp does not switch on, or shows unstable operation, use the
configurator in the MIN or VIRTUAL CONFIGURATION position to select
the minimum level of light intensity, until a value is obtained that gives
the possibility of adjusting the operation of the lamp.
7. Wiring diagram
L
N
In addition to the M position, also positions TY and MIN must be configured
TY
Configurator
None or 0
Type of
load
inductive
LED
1 inductive
CFL
2 capacitive
LED
3 capacitive
CFL
4 Halogen
lamp
Note: CFL = compact fluorescent lamp
Minimum light Switch on mode
intensity level
(default)
10 Switches on at
minimum level,
and then adjusts to
the saved level
37 Switches on at
maximum level,
and then adjusts to
the saved level
10 Switches on at
minimum level,
and then adjusts to
the saved level
37 Switches on at
maximum level,
and then adjusts to
the saved level
1 Switches on at
minimum level,
and then adjusts to
the saved level
230V
C16
T1,6H 250V
220-240V ~ 50 - 60 Hz
110-127V ~ 50 - 60 Hz
12W19
ID
200W
100W
BUS SCS
BT00594-a- EN 18/06/2012
2/2