Meade Telescope Serial Command Protocol

More documents

Recommendations

Info

$RB-60 Refracting Telescope - Meade$

Meade Telescope Protocol :StsDD*MM# Sets the current site latitude to sDD*MM# Returns: 0 – Invalid 1 - Valid :STdddd.ddddddd# [Autostar II Only] Sets the current tracking rate to ddd.dddd hertz, assuming a model where a 60.0000 Hertz synchronous motor will cause the RA axis to make exactly one revolution in 24 hours. Returns: 0 – Invalid 2 – Valid :ST+# Increment Manual rate by 0.1 Hz Returns: Nothing :ST-# :STA- Decrement Manual rate by 0.1 Hz Returns: Nothing [Autostar II only] Enable Altitude SmartDrive (PEC) Returns:Nothing :STA+ [Autostar II only] Enable Altitude SmartDrive (PEC) Returns:Nothing :STZ- [Autostar II only] Disable RA/Azimuth SmartDrive (PEC) Returns:Nothing :STZ+ [Autostar II only] Enable RA/Azimuth SmartDrive (PEC) Returns:Nothing :SwN# Set maximum slew rate to N degrees per second. N is the range (2..8) Returns: 0 – Invalid 1 - Valid :SyGPDCO# Sets the object selection string used by the FIND/BROWSE command. Returns: 0 – Invalid 1 - Valid :SzDDD*MM# Sets the target Object Azimuth [LX 16” and Autostar II only] Returns: 0 – Invalid 1 - Valid T – Tracking Commands :T+# Increment Manual rate by 0.1 Hz Returns: Nothing :T-# :TL# Decrement Manual rate by 0.1 Hz Returns: Nothing Set Lunar Tracking Rage - 16 -
Meade Telescope Protocol Returns: Nothing :TM# :TQ# :TS# Select custom tracking rate [ no-op in Autostar II] Returns: Nothing Selects sidereal tracking rate Returns: Nothing Select Solar tracking rate. [LS Only] Returns: Nothing U - Precision Toggle :U# Toggle between low/hi precision positions Low - RA displays and messages HH:MM.T sDD*MM High - Dec/Az/El displays and messages HH:MM:SS sDD*MM:SS Returns Nothing V – PEC Readout :VDNNNN# Read out Dec PEC Table Entry [Autostar II and Classic 16” only] Returns: D.DDDD Rate Adjustment factor for worm segment NNNN. PecRate = TheoreticalRate * sD.DDD for this segment :VRNNNN# Read out RA PEC Table Entry [Autostar II and Classic 16” only] Returns: D.DDDD Rate Adjustment factor for worm segment NNNN. PecRate = TheoreticalRate * sD.DDD for this segment W – Site Select :W# Set current site to , an ASCII digit in the range 1..4 Returns: Nothing – Help Text Retrieval :# Set help text cursor to the start of the first line. Returns: # The contains first string of the general handbox help file. :+# Retrieve the next line of help text Returns: # The contains the next string of general handbox help file :-# Retrieve previous line of the handbox help text file. Returns: # The contains the next string of general handbox help file - 17 -
Page 1 and 2: Meade Telescope Serial Command Prot
Page 3 and 4: Meade Telescope Protocol :CM# Synch
Page 5 and 6: Meade Telescope Protocol During GPS
Page 7 and 8: Meade Telescope Protocol A ‘#’
Page 9 and 10: Meade Telescope Protocol :hW# :h# A
Page 11 and 12: Meade Telescope Protocol “LOW PRE
Page 13 and 14: Meade Telescope Protocol :RgSS.S# S
Page 15: Meade Telescope Protocol 0 - Invali
Page 19: Meade Telescope Protocol :SpB# :SpH

Meade Telescope Serial Command Protocol

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?