Sikkens Cetol TS Interior - Decorating Warehouse
Sikkens Cetol TS Interior - Decorating Warehouse
Sikkens Cetol TS Interior - Decorating Warehouse
- No tags were found...
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Cl/SfB<br />
V<br />
Akzo Nobel Woodcare<br />
Distributed in RIBA Keyfile Library<br />
January 2001 M312404a<br />
<strong>Sikkens</strong> <strong>Cetol</strong> <strong>TS</strong> <strong>Interior</strong><br />
BENEFI<strong>TS</strong><br />
COMPOSITION<br />
Medium build (Ref: BS EN 927-1 : 1997) solvent-borne interior varnish to protect and<br />
aesthetically enhance interior hardwoods and softwoods. <strong>Sikkens</strong> <strong>Cetol</strong> <strong>TS</strong> <strong>Interior</strong> is a<br />
single product system that provides a hardwearing finish that is resistant to knocks, spills<br />
and abrasion.<br />
•<br />
Satin finish<br />
•<br />
•<br />
•<br />
Resistant to knocks and abrasion<br />
Enhances the timber’s visual characteristics<br />
Available in colourless, and 9 ready mixed colours<br />
Micronised iron oxide pigments dispersed in a special synthetic resin.<br />
PROPERTIES<br />
Solids Content<br />
By weight 34%<br />
Finish<br />
Drying Times (@20˚C/65%RH)<br />
Coverage<br />
Washability<br />
PREPARATION<br />
Satin<br />
Touch dry : 3 hours<br />
Recoatable : 16 hours<br />
Note: Dependent upon absorption and drying conditions. Certain hardwoods are often rich in natural oils or<br />
extractives that can seriously affect the drying, absorption and adhesion of all finishes. These must be removed<br />
by wiping the surfaces with a cloth dampened with cellulose thinners or equivalent.<br />
12-14 m 2 /litre on smooth surfaces, this will vary depending upon the method of application, timber species,<br />
moisture content, timber cut, and the presence of other coatings.<br />
Resistant to washing and scrubbing. Clean with a mild detergent solution or white spirit to remove dirt and stains.<br />
Timber surface must be thoroughly abraded, clean and dry, with dust, dirt, wax and grease removed. The<br />
moisture content of timber must not exceed 14%. Resinous areas, knots and timbers with a high natural oil (e.g.<br />
teak,) or extractive (e.g. oak, iroko) content, should be thoroughly degreased by wiping with a cloth dampened<br />
with cellulose thinners. Existing varnish or high build stain finishes should be lightly sanded with a fine grade<br />
abrasive paper to provide a suitable key. We do not recommend the use of “knotting agents”, which are not<br />
always fully effective in “sealing in” resin. In addition, the presence of knots is often highlighted, and adhesion of<br />
subsequent coatings can be impaired.<br />
<strong>Cetol</strong> <strong>TS</strong> <strong>Interior</strong><br />
APPLICATION<br />
CONDITIONS<br />
Avoid applying in high relative humidity or when the air/substrate temperatures are below 8˚C or above 30˚C.<br />
APPLICATION<br />
Ensure product is thoroughly stirred before and during application, otherwise colour and sheen variations may be<br />
experienced.<br />
Apply 3 coats of <strong>Cetol</strong> <strong>TS</strong> <strong>Interior</strong> to a wet film loading 60 micrometres per coat, lightly sanding between<br />
coats. <strong>Cetol</strong> <strong>TS</strong> <strong>Interior</strong> should be applied by brush in a full flowing coat and brushed out to ensure even<br />
coverage. Avoid overbrushing, as this will cause brush marks and a poor quality finish. For the best results the<br />
room should be dust free. The depth of colour achieved will be dependent upon the colour of the wood or<br />
existing finish and the number of coats of coloured <strong>Cetol</strong> <strong>TS</strong> <strong>Interior</strong> applied, we therefore strongly recommend<br />
that a trial application is carried out to ensure acceptability. If the required depth of colour is achieved in less<br />
than three coats, complete the full specification with colourless <strong>Cetol</strong> <strong>TS</strong> <strong>Interior</strong>.<br />
<strong>Cetol</strong> <strong>TS</strong> <strong>Interior</strong> is formulated for brush application and is supplied ready for use. However for surfaces that are<br />
particularly porous, apply a first coat of varnish thinned with clean white spirit in the volume ratio of one part<br />
white spirit to 9 parts <strong>Cetol</strong> <strong>TS</strong> <strong>Interior</strong>, followed by 2 coats of unthinned <strong>Cetol</strong> <strong>TS</strong> <strong>Interior</strong>.<br />
Only use non-rusting screws, nails and fixings.<br />
Cleaning<br />
Brushes should be cleaned immediately after use with clean white spirit
<strong>Sikkens</strong> <strong>Cetol</strong> <strong>TS</strong> <strong>Interior</strong><br />
MAINTENANCE<br />
<strong>Cetol</strong> <strong>TS</strong> <strong>Interior</strong> treated surfaces may be cleaned by wiping down lightly with a damp cloth and then buffing<br />
with a dry cloth to restore the original sheen. The use of silicone-based or wax polishes is not recommended as<br />
they tend to accumulate dirt and make maintenance re-applications of <strong>Cetol</strong> <strong>TS</strong> <strong>Interior</strong> impossible unless fully<br />
sanded and degreased.<br />
Should maintenance become necessary, the surfaces should be lightly sanded with a fine grade abrasive paper. If<br />
the timber has been stained, avoid sanding back to the underlying stain. Remove all sanding dust and apply one<br />
or two coats of <strong>Cetol</strong> <strong>TS</strong> <strong>Interior</strong>.<br />
COMPATIBILITY<br />
<strong>Cetol</strong> <strong>TS</strong> <strong>Interior</strong> may be applied over most varnishes and woodstains including the following <strong>Sikkens</strong> products;<br />
<strong>Cetol</strong> HLS, <strong>Cetol</strong> THB and <strong>Cetol</strong> Filter 7. Data sheets are available on all other <strong>Sikkens</strong> products mentioned.<br />
Compatibility with respect to adhesion and colour should be ensured with a trial application before full treatment<br />
commences. Similar products to those mentioned above will also show good compatibility with <strong>Cetol</strong> <strong>TS</strong><br />
<strong>Interior</strong>. For further advice on this refer to the manufacturers of such products, or contact us on the number<br />
given at the end of this data sheet.<br />
STORAGE<br />
The can should be resealed after use and stored tightly closed to prevent evaporation and entry of oxygen.<br />
Avoid the inclusion of a greater proportion of air to the liquid product. It should be noted that even if there is a<br />
higher proportion of product to air in the container, once opened the shelf life of the product is unpredictable.<br />
Store in a cool, dry place.<br />
CAN SIZES<br />
<strong>Cetol</strong> <strong>TS</strong> <strong>Interior</strong> is available in 1 litre cans and 2.5 litre cans for most ready mixed colours.<br />
SAFETY, HEALTH<br />
& ENVIRONMENT<br />
<strong>Sikkens</strong> is a brand of Akzo Nobel Woodcare, a division of Akzo Nobel Decorative Coatings Limited. It is the<br />
policy of Akzo Nobel Woodcare to provide the highest standard of safety, health and environmental advice<br />
and information.<br />
To this end, material safety data sheets covering every Akzo Nobel Woodcare product are supplied to our<br />
customers and are freely available to users on request, by contacting us on the number given below.<br />
The safety phrases on the container and material safety data sheet should be read before using this product.<br />
GENERAL<br />
INFORMATION<br />
Apply all products in accordance with BS 6150 : 1991 and BS 8000 - 12 : 1989.<br />
Information on British Standards can be obtained from British Standards Institute. Tel:0208 996 9000.<br />
Every care is taken to ensure that the information provided in this technical data sheet is accurate.<br />
Akzo Nobel Woodcare is unable to guarantee results as it has no control over the conditions under which its<br />
products are applied.<br />
For further help and information contact the Woodcare Advice Centre on 01480 496868. Before using this<br />
product ensure that you have the latest information available. The information above is correct at the date of<br />
issue, January 2001.<br />
AKZO NOBEL<br />
Akzo Nobel Woodcare,<br />
Meadow Lane, St Ives, Cambs, PE27 4UY.<br />
Tel: 01480 496868 Fax: 01480 496801<br />
Email: woodcare@stives.deconorth.com<br />
Web Address: www.sikkens.co.uk<br />
www.woodprotection.co.uk<br />
4ABXJ02700/01/01