NS 68K - DamenCNC.com

IMB-7.2006
Phase-angle dimmer NS 68
for ohmic and inductive
consumers up to 2200 Watts
NS 68
with H-15 strip
NS 68 K
with screw terminal
NS 68 A
Series connection device
for increasing output
with H-15 strip
NS 68 AK
Series connection device
for increasing output
with screw terminal
This phase-angle dimmer family
consists of phase section controllers
which can be controlled as a special
feature with a control voltage of 0 - 10 V or
with a 10 k potentiometer.
Application areas:
• Floodlights
• Light control systems
• Electric tools
• Heating equipment
• Test equipment
• Universal and shaded-pole motors
• Vibration conveyors
• Angle grinders
• and many more
The circuit is fitted with a so-called
softstart. This means that when the
mains power is switched on, the current
conduction angle starts slowly, however
the external control itself is not delayed.
The presence of the mains voltage and
the control voltage is indicated using
LEDs. The minimum phase section angle
(preheating) and the maximum control
limit can be set separately and
independent of each other using trim
potentiometers.
The controller card is also protected
against overload using a thermal switch.
NS 68 A (AK)
The output can be increased by 2.2 kW
with this series connection card
(max 6.6 kW)
FG-ELEKTRONIK GmbH
Mühlweg 30-32
D-90607 Rückersdorf
Telephone +49(0)911/57545-0
Fax +49(0)911/570100
Website www.fg-elektronik.de
Email fg@fg-elektronik.de

Phase-angle dimmer NS 68
Technical data: NS 68 or NS 68 K NS 68 A or NS 68 AK
Base module
Series connection module
Connection voltage 230 V AC for increasing output
Connection frequency 47...63 Hz by 2,200 Watts
max. continuous load 2200 Watt (max 6.6 kW)
Control (external)
0 - 10 V or potentiometer 10 k
Control range
15 - 230 V
Type of load
ohmic / inductive
Input resistance of the
control input 100 k Ohm all other data identical
Control principle Phase control with base module NS 68
Fuse
F 10 A
Ambient temperature - 10...+ 40 °C
Dimensions L x W x H 160 x 100 x 52 mm
Weight
600 g
Connection NS 68 = H-15 multipoint connector NS 68 A = H-15 multipoint connector
NS 68 K = Screw terminal
NS 68 AK = Screw terminal
The EMC limit values according to EN 55014, IEC 1000-4-4, IEC 1000-4-5 are maintained.
Connection assignment:
Lamp
PE for load
Series
Protective
earth
Power cable
30 26 22 18 14 10 6
L1 N Load • • Load PE • • GND
•
• PE • L 1 • N Load PE CC +12V • CC •
32 28 24 20 16 12 8 4
For operation with external control voltage:
4 = + CC controller
6 = GND
= connected on circuit board
10 k
HSH 2
NS 68 with DIN rail holder HSH 2
Option:
19 inch part front plate FP 10 V
with handle and connecting piece,
50 mm wide, 3 HE,
order No. FP 10 V
Rotary potentiometer 10 k, order No.
DPO 5
Socket strip H 15 B
for 6.3 mm flat connector
Socket strip H 15 BP
for print installation
DIN rail holder HSH 2
for switch cabinet installation
Technical specifications subject to alteration.