Magnetic pulse encoder GO1 - ZEITLAUF antriebstechnik
Magnetic pulse encoder GO1 - ZEITLAUF antriebstechnik
Magnetic pulse encoder GO1 - ZEITLAUF antriebstechnik
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
<strong>Magnetic</strong> <strong>pulse</strong> <strong>encoder</strong><br />
<strong>GO1</strong><br />
<strong>antriebstechnik</strong><br />
it’s time for tomorrow<br />
Technical data<br />
Order code<br />
G01.2.2<br />
No. of <strong>pulse</strong>s [Z] 2 Pulses per revolution (A and B)<br />
Output signal [A,B] 2 rectangular signals 90° ± 15° phase offset,<br />
90° ± 15°, when G03 ±40° electr. phase offset<br />
Pulse ratio Pulse: Pause = 180° : 180° ± 10°<br />
Edge steepness, rise < 400 ns (U = 12 VDC, RL = 820 Ohm)<br />
Edge steepness, fall < 400 ns (U = 12 VDC, CL = 20 pF)<br />
Output load current [I load ] < 12 mA (U = 12 VDC)<br />
Electronics configuration Open collector output stage with internal pull-up resistors<br />
Supply voltage: U B = 4,5 to 24 VDC (protected against polarity reversal)<br />
Output amplitude: U low < 0,4 V (at 12 VDC +20 mA)<br />
Electrical connection 4 individual Litz wires AWG 24, 500 ± 30 mm long<br />
Litz ends stripped and tin-plated 7 ± 2 mm<br />
Assignment [colour] red: + 5 V…24 V | yellow: A-channel | black: = 0V | green: B-channel<br />
Weight [kg] 0,03<br />
90° electrical<br />
phase offset<br />
A-channel<br />
B-channel<br />
<strong>Magnetic</strong> <strong>pulse</strong> <strong>encoder</strong><br />
• <strong>Magnetic</strong> <strong>pulse</strong> <strong>encoder</strong> for direct current motors<br />
• The <strong>encoder</strong> is designed for speed recording, control and positioning in conjunction with<br />
suitable electronics.<br />
• The <strong>encoder</strong> is contactor-less and wear-free via 2 Hall sensors. The sensors are<br />
positioned around a magnet and generate two rectangular-<strong>pulse</strong> signals offset by 90°.<br />
• The <strong>encoder</strong> unit is screwed onto the motor. The electrical connection is via litz wires.<br />
• Electrical protection IP 40<br />
• Temperature range -20 °C to +80 °C<br />
Diagram pattern with shaft rotating clockwise.<br />
Looking towards motor shaft.<br />
Attention: One accessory per gear motor only.<br />
<strong>ZEITLAUF</strong> ® GmbH <strong>antriebstechnik</strong> & Co KG<br />
Industriestraße 9<br />
D-91207 Lauf a. d. Pegnitz<br />
Postfach 100130<br />
D-91191 Lauf a. d. Pegnitz<br />
Tel. +49 (0) 9123 / 9 45-0<br />
Fax +49 (0) 9123 / 9 45-145<br />
info@zeitlauf.com<br />
www.zeitlauf.com<br />
Die Informationen, Abbildungen, technischen Beschreibungen und sonstigen Angaben auf dieser Website sind unverbindlich und unterliegen dem Vorbehalt der jederzeitigen technischen oder inhaltlichen<br />
Änderung. Deshalb ist jede Haftung für die Richtigkeit und Vollständigkeit der Information ausgeschlossen. Alle Inhalte (Texte, Abbildungen, Zeichnungen) sind urheberrechtlich geschützt und unterliegen<br />
den geltenden Urhebergesetzen. Kopie und Nachahmung, auch auf technischer Ebene, sowie Weitergabe an Dritte sind ausdrücklich verboten.<br />
All information, illustrations, technical descriptions and other details quoted on this website are given without commitment, and are subject to alterations of a technical nature or of content without<br />
notice. No liability whatsoever is accepted for accuracy or completeness of the information given. All contents (texts, illustrations, drawings) are protected by copyright, and are subject to current<br />
copyright legislation. Copying and imitation, also of a technical nature, as well as transmitting to third parties are strictly forbidden.
<strong>Magnetic</strong> <strong>pulse</strong> <strong>encoder</strong><br />
<strong>GO1</strong><br />
<strong>antriebstechnik</strong><br />
it’s time for tomorrow<br />
4 Litz wires AWG24<br />
Tin-plated litz ends<br />
B side of the motor<br />
Motor L ± 05 [mm]<br />
M4210 18<br />
BCI42... 18<br />
ECM42… 24*<br />
ECM48… 24*<br />
BCI52... 18<br />
BCI63... 18<br />
GK63… 18<br />
ECM63… 24*<br />
ECM75… 24*<br />
M8080 23*<br />
* incl. additional flange<br />
<strong>ZEITLAUF</strong> ® GmbH <strong>antriebstechnik</strong> & Co KG<br />
Industriestraße 9<br />
D-91207 Lauf a. d. Pegnitz<br />
Postfach 100130<br />
D-91191 Lauf a. d. Pegnitz<br />
Tel. +49 (0) 9123 / 9 45-0<br />
Fax +49 (0) 9123 / 9 45-145<br />
info@zeitlauf.com<br />
www.zeitlauf.com<br />
Die Informationen, Abbildungen, technischen Beschreibungen und sonstigen Angaben auf dieser Website sind unverbindlich und unterliegen dem Vorbehalt der jederzeitigen technischen oder inhaltlichen<br />
Änderung. Deshalb ist jede Haftung für die Richtigkeit und Vollständigkeit der Information ausgeschlossen. Alle Inhalte (Texte, Abbildungen, Zeichnungen) sind urheberrechtlich geschützt und unterliegen<br />
den geltenden Urhebergesetzen. Kopie und Nachahmung, auch auf technischer Ebene, sowie Weitergabe an Dritte sind ausdrücklich verboten.<br />
All information, illustrations, technical descriptions and other details quoted on this website are given without commitment, and are subject to alterations of a technical nature or of content without<br />
notice. No liability whatsoever is accepted for accuracy or completeness of the information given. All contents (texts, illustrations, drawings) are protected by copyright, and are subject to current<br />
copyright legislation. Copying and imitation, also of a technical nature, as well as transmitting to third parties are strictly forbidden.