NATUROL OEL NATUROL OEL-LASUR - Pentol

More documents

Recommendations

Info

Technical Technical Data Data Sheet Sheet No. No. 2056 2056 Page Page 2 of of 3 Preparation Preparation Substrate Substrate Substrate Product Data sheet Coat thickness Preparation Preparation for for for new new cladding: cladding: Impregnation 1 x Pentol Stabilo FFF, all sides 207400 Intermediate sanding P 150 - 180 grain Fladder brushes Intermediate coat 1 x Naturol Oel-Lasur, all sides 205600 Top coat 1 x Naturol Oel-Lasur, visible sides 205600 Surface Surface Surface preparation preparation preparation Application Application Pentol Pentol Pentol Holzschutz, Holzschutz, Holzschutz, CH CH-9430 CH 430 St. St. St. Margrethen Margrethen Margrethen Please contact our technical staff for further application suggestions. Substrate Substrate Every substrate must be clean, dry and free of grease and oil. Moisture content of the wood: Max. 16% Amount per coat: Planed / sanded wood surfaces ca. 70 g/m 2 Unplaned wood surfaces ca. 120 g/m 2 Naturol Oel-Lasur can also be used on rough lumber if no agents are required to preserve the wood. Personal Personal protection protection Even if not required by law, wearing personal protective equipment is recommended. CH: The precautions prescribed by SUVA with respect to hygiene and equipment must be observed. Stirring Stirring Stir glaze well before use. Dilution Dilution Ready to use Brush Brush Brush painting painting Undiluted Rolling Rolling Undiluted
Technical Technical Data Data Sheet Sheet No. No. 2056 2056 Page Page 3 of of 3 Pentol Pentol Pentol Holzschutz, Holzschutz, Holzschutz, CH CH-9430 CH 430 St. St. St. Margrethen Margrethen Margrethen Viscosity Dilution Nozzle Pressure Spray coats Gravity Gravity feed feed gun gun 22 s DIN 4mm None 1.5 – 1.8 3 bar 1 cross-spray Airless Airless Airless (airmix) (airmix) spraying spraying 22 s DIN 4mm None 09 – 11 (Wagner) Vacumat Vacumat – Automatic Automatic spraying spraying machines machines – Brushing Brushing machines machines 22 s DIN 4mm 0 – 10% Drying Drying time time At 23° C and 65% rel. humidity Important Important Important information information Dust-dry after: 6 h Touch-dry after: 12 h Recoatable after: 24 h 3-4 bar 1 cross-spray Special Special restrictions restrictions The suitability of Naturol Oel-Lasur is limited for hardwoods and exotic woods. If using Naturol, always spot test first! Minimum Minimum aapplication a pplication and and drying drying temperature temperature Coat Coat removal removal Sanding 10 °C Not below the dew point. Equipment Equipment cleanup cleanup cleanup With Sangajol V400. Dried material with thinner V130. This data sheet is for your reference and information only. The above data are correct to the best of our knowledge. We offer no guarantees for use and exclude any liability. This applies in particular to consequential damage. We are not liable for any advice given by our employees. Our employees give non-binding information only. Site supervision, compliance with handling regulations, and adherence to recognized engineering rules are the responsibility of the manufacturer, even if our employee was on site during handling. Modifications due to technical developments may be made. The latest version of this information is applicable. In special cases, please request separate technical specifications.
Page 1: Technical Technical Data Data Sheet

NATUROL OEL NATUROL OEL-LASUR - Pentol

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?