Weighing Indicator Model MW-LC. - RPI - M.Lysek
Weighing Indicator Model MW-LC. - RPI - M.Lysek
Weighing Indicator Model MW-LC. - RPI - M.Lysek
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
<strong>MW</strong>-<strong>LC</strong><br />
<strong>MW</strong>-<strong>LC</strong><br />
0<br />
NET<br />
PCS<br />
MENU<br />
MEMO<br />
L1<br />
L2<br />
ESC<br />
<strong>Weighing</strong> <strong>Indicator</strong><strong>Model</strong><strong>MW</strong>-<strong>LC</strong>.<br />
multi rangefacility<br />
multi point calibration<br />
piececount<br />
2set points<br />
printer output &software(programable header)<br />
RS232 andRS485<br />
power supply 12or 24 Vdc<br />
excitation 10VDC -1kHzwith sense<br />
for 1-6loadcells, 350Ohm<br />
50 conversions /s<br />
full softwarecontrolled<br />
INDUSTRIALWEIGHING &DOSING<br />
Tel:++(0)318-525630 e-mail:info@penko.com<br />
Fax: ++ (0)318 -529715 Web-site:www.penko.com
+<br />
12VDC<br />
-<br />
INPUTS:<br />
PIN5,6,7,8,13,14,15<br />
COMMONS: PIN 1,2,3,4<br />
INPUTS:<br />
INPUT1=5 INPUT4=14<br />
INPUT2=13 INPUT5=7<br />
INPUT3=6 INPUT6=15<br />
SLOPINGHEIGHT<br />
DETECTION=8<br />
Inputs<br />
/outputs<br />
not<br />
opto<br />
isolated<br />
Max. 50mA<br />
+<br />
12VDC<br />
-<br />
OUTPUTS:<br />
OUT1=12<br />
OUT2=11<br />
COM I/O=1-4<br />
ON/OFF=9-10<br />
OUTPUTS: PIN11,12<br />
COMMONS: PIN 1,2,3,4<br />
PIN9<br />
or<br />
ON/OFFSWITCH<br />
PIN10<br />
Thisunitmust be earthed<br />
Referservicingtoqualified personnel only<br />
I/O CONNECTOR<br />
Nouser serviceable partsinside<br />
INPUTS:<br />
IN1=5 IN4=14<br />
IN2=13 IN5=7<br />
RS232<br />
IN3=6 IN6=15<br />
SLOPINGHEIGHT<br />
OUTPUTS max. 50mA DETECTION=8<br />
TYPE:<br />
S/N:<br />
OUTPUTS:<br />
OUTPUT1=12<br />
OUTPUT2=11<br />
SUPPLY<br />
LOADCELL(S)<br />
1 2 3 4 5 6 7 8 910<br />
SUPPLY:<br />
MADE IN<br />
HOLLAND<br />
POWERSUPPLY<br />
-------------------------<br />
10-28V DC<br />
Straingauge<br />
transducer(s)<br />
6wire sense<br />
system<br />
Specifications<br />
Power supply<br />
10 -28 VDC.<br />
Display 6digits0.56"-17 mm<strong>LC</strong>D.Maximumreading +999.999 to -99.999<br />
Measurement<br />
Ratio metric:Systemreference isrelated to the excitation voltage.Any changein excitation voltage<br />
will not have influence on the reading.<br />
Sample rate<br />
50 conv/s.<br />
Resolution<br />
Up to 16.000.000.parts.(24 bit)<br />
Excitation voltage <strong>LC</strong> DC to -1kHz.(default250Hz) Wiring- 6Wire sensesystemfor1-6 loadcells350 Ohm.<br />
Sensitivity<br />
1-1,5-2-2,5 -3or3,5mV/V.<br />
Dead Load<br />
Digitally compensated.<br />
Temperature range Operating -10 -+40ºC.Storage -25-+80ºC.<br />
Linearity error<br />
±0.0015 ‰ FS.Typical;0.03 ‰ FS max.<br />
Gain drift<br />
±4ppm/ºC(by 2mV/V).<br />
Offset drift<br />
±0.005 µV/ºC<br />
Polarity<br />
Uni-or Bipolar inputrange.<br />
Digital filter<br />
Providesrejection off allfrequenciesabove 12 Hz.--> 50Hz :rejection 70dB.<br />
Calibration<br />
User friendly calibrationand set-up.<br />
Communication RS 232,full duplexandor 1xRS 485, 1x RS 422.<br />
Protocol<br />
PC,PR orPV protocol-configurable.<br />
Housing<br />
Extruded and machinedaluminum.<br />
Dimensions builtin: 138 x68 x60 mm. front: 150 x78 x5mm. without connectors.<br />
Weight<br />
About 550g<br />
Striking features<br />
User configurable printer headers.<br />
Easy two setpoint operation. (Opencollector 25 mA)<br />
Persistentstorage up to10 presettarevalues<br />
Piece weighing. 0.0000g/pcs.<br />
Technical improvementsmay cause thespecifications to change.<br />
Penko EngineeringB.V.Wageningselaan 52-54, 3903 LAVeenendaal, Postbus399, 3900AJ Veenendaal,<br />
Telefoon: ++(0)318 525630*, e-mail: info@penko.com Web-site:www.penko.comFAX: ++(0)318 529715,<br />
Bank: MeesPierson Rotterdamnr.25.67.24.601, Postgiro v/d Bank: 6400, K.v.K. Utrecht nr. 67751.
Change language