Kenall_TopDek

Topdek 

Advanced Lighting for Parking Applications 

Transportation 

TR 

WINNER

2 

Kenall Lighting TopDek 

Table of Contents 

TopDek Advanced Lighting for Parking Garages 

Introduction 3 

Architectural Design 4 

Construction & Maintenance 5 

Glare 6-7 

LED Commitment 8 

Thermal Management 9 

Photometrics & Layout 10-11 

Ordering Information 12 

Wind Loading & EPA Calculations 13 

Mounting & Installation 14 

SmartSense Micro 15 

SmartSense Control System 16-17 

Savings & Sustainability 18 

Complementary Parking Garage Products 20-21 

Warranties & LED Listings 22 

Specification Sheet 23 

* 

* TopDek is the first Parking Area/Surface Lot luminaire with an 

efficacy exceeding 100 lumens per watt, according to the U.S. 

Department Of Energy's Lighting Facts program. In fact, Kenall's 

highest efficacy product achieves 110 lumens per watt, setting 

a new benchmark in optical efficiency— particularly impressive for 

a full cutoff fixture with a low-glare secondary lens! 

The illustration above shows TopDek operating at 100% full light output on the structure’s top level, completely illuminating the parking deck. 

In contrast, the sub levels are shown operating at 20% of full brightness to optimize the energy saving potential of the control system. 

www. kenall.com P: 800-4-Kenall Email: info@kenall.com 1020 Lakeside Drive Gurnee, Illinois 60031 

The Kenall product shown on this page is designed and manufactured in the USA with components purchased from US suppliers, and meets the Buy 

American requirements under the ARRA. Kenall has not determined the origin of its domestically purchased components or the subcomponents thereof.


3 

Kenall Introduces TopDek 

Advanced Parking Deck Lighting 

WINNER 

With the tremendous acceptance of TekDek LED with SmartSense controls, Kenall has developed a top of deck/surface 

lot luminaire as a complement to this revolutionary new product family. 

Aesthetically pleasing, TopDek is appropriately scaled for use in a wide variety of parking applications. Its robust 

feature set includes: 

• Traditional aesthetic with a long life LED source 

• A unique optic configuration for unprecedented 

glare control and enhanced uniformity 

• Field rotatable optics for added distribution flexibility 

• An integrated houseside shield without impacting 

EPA to control light trespass 

• A concealed heat sink for effective thermal 

management 

• Hinged access for ease of maintenance 

• Optional daylight and occupancy controls for 

additional energy savings 

With the introduction of TopDek, facility owners can now use Kenall to illuminate the entire parking structure including 

all covered and uncovered parking areas and stairwell locations. In addition, we’re confident you’ll find TopDek’s 

universal aesthetic appeal, unprecedented glare control, and long LED life second to none in the industry. 




4 


TopDek Sleek Architectural Design 

TopDek’s intelligent, low profile design provides a sleek, traditional aesthetic. The luminaire's integrated heat sink technology features 

concealed fins that draw heat away from thermally sensitive electronics to maximize LED and driver life. TopDek’s innovative, patentpending 

optical system provides unprecedented glare control without sacrificing uniformity and efficacy. 

Sleek Architectural Design 

Appropriately scaled for mounting 15-30 feet above ground, TopDek's sleek 

architectural design and traditional aesthetic provide universal appeal. 

Concealed Heatsink Technology 

TopDek's concealed heatsink provides effective thermal management 

essential to maximizing LED life. Moreover, the concealed fins provide a 

desirable architectural styling atypical of most LED parking deck luminaires. 

Rotatable Optics 

Direct the photometric distribution without changing the luminaire 

orientation. Optics are adjusted in 90 degree increments. 

Architectural Mounting Arm 

The decorative mounting arm is upswept to 

gracefully suspend the luminaire overhead 

without any visible mounting hardware. 

Full-Cutoff Distribution 

All distributions are Dark Sky compliant; 

emitting no uplight while also minimizing 

glare and high angle light. 

House-side Shield 

The luminaire's unique optional integrated 

house-side shield restricts light trespass, 

preventing spill onto adjoining properties. 





TopDek Durable Construction, Maintenance Friendly 

TopDek's rugged, thoughtfully constructed design eases installation and maintenance, and maximizes component life. Manufactured in the USA, 

the fixture's housing is constructed of marine-grade diecast aluminum for maximum strength and durability. Hinged access and field rotatable 

optics make TopDek easy to install and maintain—a highly desirable feature in both top of deck and surface lot applications. 

5 

Clamshell Housing 

To reduce weight during retrofit installation and maintenance, the housing's 

clamshell design enables the top portion of the fixture to be mounted to the pole, 

followed by easy placement of the weightier, lower portion onto the lipped hinge. 

Convenient Gear Tray 

The luminaire's gear tray facilitates the maintenance of electrical components while 

simultaneously providing protection from the elements . 

Sealed Optic and Electrical Compartments 

TopDek's IP65 sealed optic and electrical compartment enable air and water to flow 

through the housing without affecting any electrical components or the lamp source. 

Thermal Management 

Thermal management design optimizes LED performance, maximizing 

component life. 

C 

IP65 

LED 

Dual Optic System 

TopDek's 90° field-rotatable, dual optic 

system offers unprecedented glare control and 

enhanced flexibility in light distribution. 

Thermal Management 

The flow-through design facilitates the 

dissipation of heat while maintaining the 

integrity of the LED lamp source. 

Optional Sensor 

TopDek offers an integrated SmartSense 

Micro option, which is removed from the heat 

source, sensing motion and daylight at the 

individual luminaire level. 




6 


TopDek Unprecedented Glare Control 

Technological Innovation with a Traditional Look 

TopDek's innovative, patent pending optical technology and design delivers unprecedented glare reduction in today’s parking deck 

and surface lot environments. With the addition of a specially designed textured lens working in conjunction with the LED lamp source, 

discomfort glare is dramatically reduced. TopDek's optional integrated house-side shield controls light trespass, preventing unwanted 

light spill onto adjoining properties and offers an environmentally friendly design for units mounted near adjoining properties. 

Gap Between LED and Diffuser 

The gap between the LED and the 

diffuser serves to reduce LED pixelation. 

Secondary Optic 

Provides the precise pattern 

required for different photometric 

distributions. 

Reflector 

Highly specular reflector to 

redirect stray light downward 

and out through the lens. 

LED 

Light emitting diode package with 

integral primary optic provides 

lambertian half-space distribution. 





7 

It has long been understood that an unshielded lamp is the most efficacious manner in which to provide light, but it has for 

decades been considered unacceptable. According to IESNA RP-20-98, "Reasonable shielding of lamps, reflectors, or lenses will enhance 

the visibility and should be considered during the design process. Glare presents more of a problem for older persons, affecting their ability 

to clearly perceive objects or obstructions." Kenall's TopDek has been specifically designed with a clear textured lens to create a uniformly 

luminous surface while significantly reducing glare. 

LED Drivers 

Removed from thermal path and utilizes 

two drivers for reduced heat load, increased 

efficiency, and redundant power supply. 

Clear Textured Diffuser 

Textured surface helps break up the LED 

imaging, creating a uniformly luminous 

surface, which drastically reduces glare 

while having minimal effect on the 

photometric distribution. 

Glare is often quantified using "luminance". Luminance is a photometric 

measure of the luminous intensity per unit area of light travelling in a given 

direction. It describes the amount of light that passes through a particular 

area (luminous opening), and falls within a given solid angle. The metric unit 

for luminance is candela per square meter (cd/m2). 

The significant component of this definition is the "area", which does not 

refer to the luminaire's overall dimensions but rather its luminous opening, 

or the area that emits light from the luminaire. With LED luminaires, this area 

is the surface area of the chip itself which causes intense glare. TopDek uses 

the entire diffuser surface to maximize this area, thus minimizing glare. 




8 


Kenall Committed to LED Technology 

Advanced Technology and Testing 

As a recognized leader in the commercial lighting industry, Kenall is committed to investing considerable resources into the research and 

development of advanced lighting products. As a pioneer in solid state lighting, Kenall has long recognized LEDs as a strong and viable 

source for commercial lighting fixtures—providing tremendous opportunity for dramatic cost savings, intelligent energy reduction, and 

the preservation of natural resources. Our commitment to the advancement of lighting solutions is evidenced by Kenall’s in-house, stateof-the-art 

certified safety laboratory, membership in the Department of Energy’s LED Quality Advocate program, and unrelenting focus on 

performance listings. At Kenall, commitment is a word we take very seriously. 

Kenall Committed to LED Technology 

LED sources present an ideal solution for exterior and parking 

garage lighting. Low energy consumption and high efficacy, in 

concert with a 100,000-hour or better lamp life at 25°C and 

low heat output, create the ideal source for many applications. 

The substantial lamp life of an LED also reduces its maintenance 

requirements, which significantly reduces lifetime costs. In 

addition, LED sources contain no toxic mercury and emit no 

harmful UV radiation, creating a truly green source. Its modular 

design facilitates product upgrades, reducing the material that 

ends up in landfills, further increasing its sustainability. 

Design Lights Consortium Approved Lab 

Kenall's photometric laboratory is ISO/IEC 17025 accredited, 

providing the credentials to obtain timely Department of 

Energy Lighting Facts ® listings, Design Lights Consortium approvals, 

and EPA recognition for ENERGY STAR. Inclusion in the 

list of approved testing labs greatly enhances Kenall's ability to 

provide more comprehensive energy efficiency testing with the 

benefit of shortened lead times. 

Kenall Sophistication in Testing 

Whether testing a luminaire’s photometry or its ability to 

protect against the ingress of dust or water, Kenall is equipped 

with a state-of-the-art certified safety laboratory, providing the 

following testing capabilities: 

• Certified for safety testing by Underwriters Laboratory 

and Intertek Testing Laboratories for Incandescent, 

Fluorescent and HID Luminaires (UL 1598), LED Luminaires 

(UL 8750) Hazardous Locations (UL 844, Class I Div II, 

and Emergency Lighting (UL 924) 

• Ingress Protection testing (Dust and Water chambers) 

• Highly Accelerated Stress Screening 

(-50°C to 150°C Environmental Chamber) 

• 25°C and 40°C thermal testing rooms 

• LM-79 photometric laboratory including a Type C 

goniophotometer as well as a 2-meter integrating sphere 

with spectroradiometer 




TopDek Thermal Management 


Kenall's thermal management technology, essential to maximizing LED life and performance, utilizes an innovative marine-grade diecast 

aluminum heatsink that conducts heat away from the mission critical LEDs through the top of the housing. This process is facilitated by 

a series of fins that conduct heat outward from the core of the housing via convection heat transfer. Heat passes through the fins and is 

released via the protective screen in the top of the housing, which also prevents debris from entering the luminaire. This intelligent design 

enables the LEDs to maintain a 100,000-hour minimum lifetime even at 25°C (77°F) ambient (minimum 60,000-hour life at 40°C), making 

it a strong, viable solution for demanding environmental conditions. Moreover, the concealed fins and diffusing textured lens provide a 

desirable architectural styling atypical of most pole mounted LED luminaires. 

9 

Thermal Analysis 

Wall Heat Flux (W/m2) 

500 

458 

393 

327 

262 

196 

131 

65 

0 

Heat Flux Map 

A graphical illustration of the TopDek's ability to disperse heat, represented by watts per square meter, as depicted by the orange glow along the edge of the concealed fins. 

Flow Through Design 

Air passes through the vents surrounding the lens drawing heat through the top 

of the housing. 

Convection Heat Transfer 

Heat is drawn away from the luminaire via convection heat transfer, as shown by 

the plume above the luminaire. 




10 


TopDek Photometrics 

Flexibility in Design & Illumination 

Kenall’s new TopDek LED offers eight illumination patterns, including a Type lll and Type V distribution to address a majority of parking applications. 

Visit www.kenall.com for additional distribution options. 

TopDek Polar Distribution Graph 

Type V-Square 

TopDek ISO Ft-Candle Chart 

Measured at 25' mounting height 

3 

.1 

1679 

3358 

5037 

6716 

Maximum Candela = 6716.077 Located At Horizontal Angle = 45, Vertical Angle = 60 

1 - Vertical Plane Through Horizontal Angles (45-225) (Through Max. Cd.) 

2 - Horizontal Cone Through Vertical Angle (60) (Through Max. Cd.) 

2 

1 

2 

1 

0 

1 

2 

3 

0 

.25 

.5 

.75 

1 

2 

3 

1 

2.25 3.75 

2.75 

2 3 4 

Distance In Units Of Mounting Height 

1/2 Maximum Candela Trace Shown As Dashed Curve 

1.75 

Multiplier Table 

40' = .39 

35' = .51 

30' = .69 

25' = 1.00 

20' = 1.56 

15' = 2.78 

12.5 = 4.00 

TopDek Polar Distribution 

Graph Type lll 

1915 

3831 

5746 

7662 

Maximum Candela = 7213.481 Located At Horizontal Angle = 45, Vertical Angle = 60 

1 - Vertical Plane Through Horizontal Angles (45 - 225) (Through Max. Cd.) 

2 - Horizontal Cone Through Vertical Angle (60) (Through Max. Cd.) 

2 

1 

TopDek ISO Ft-Candle Chart 

Measured at 25' mounting height 

3 

2 

1 

0 

1 

2 

3 

4 

5 

0 

.5 

1 

2 

5 

10 

20 

1 

2.25 3.75 

2 3 4 

1.75 

2.75 

Distance In Units Of Mounting Height 

1/2 Maximum Candela Trace Shown As Dashed Curve 

.2 

.1 

5 

Multiplier Table 

40' = .39 

35' = .51 

30' = .69 

25' = 1.00 

20' = 1.56 

15' = 2.78 

12.5 = 4.00 

Light Output Ratings 

TopDek is available in three different engines with either 5700K, 5000K or 4000K color temperatures for a total of nine distinct configurations. These LEDs can be 

driven at 350mA for maximum efficacy (lumens per watt), at 525mA or at 700mA for maximum output. The performance matrix below summarizes the output for 

each of these configurations in “delivered lumens,” which is the preferred reporting method of the Department of Energy’s Lighting Facts program. Delivered lumens 

measures the true light output leaving the luminaire after considering all of the thermal, optical and electrical losses that are present in every luminaire. 

For comparative purposes, always demand ratings in delivered lumens. 

Performance Matrix 

Delivered Lumens 

LED Color (°K) Drive Current (mA) Input Watts (W) LED Engine Type III Type III HSS Type V Square Type V Round Estd. LED Life 

5700 350 112 100L57K 10,737 7,354 11,490 12,180 150,000 

5700 525 158 160L57K 14,412 9,871 15,442 16,348 150,000 

5700 700 224 216L57K 17,821 12,206 19,070 20,215 100,000 

5000 350 112 100L50K 10,042 6,878 10,764 11,391 150,000 

5000 525 158 160L50K 13,479 9,232 14,423 15,289 150,000 

5000 700 224 216L50K 16,667 11,416 17,835 18,906 100,000 

4000 350 112 100L40K 9,424 6,455 10,084 10,690 150,000 

4000 525 158 160L40K 12,649 8,664 13,536 14,348 150,000 

4000 700 224 216L40K 15,641 10,713 16,738 17,743 100,000 




TopDek Photometrics & Layout 


TopDek has been specifically designed to meet or exceed IES recommended light levels for parking decks and surface lots on poles 

up to 30' in height. Even with wide pole spacings, TopDek delivers excellent uniformity that translates into enhanced safety for 

patrons and reduced costs for owners. The layout below highlights TopDek's powerful efficacy ratings and low max to min ratios, 

which exceed IES recommendations. 

11 

Layout based on 150'×320' parking area with 25' poles on 2' bases (27' mounting height) 

Statistics 

Description AVG MAX MIN MAX/MIN AVG/MIN 

Deck Level 3.18 6.35 1.02 6.2:1 3:1:1 

Ramp 4.28 6.53 2.27 2.9:1 1.9:1 

Luminaire Schedule 

Symbol Label Qty Catalog Number Description Lamp File Lumens LLF 

VS 12 TPD23-5S-TA-GW-216L57K-DV TopDek Type V Square LED: QTY 96, 5700K, 70 CRI KPL1798-17-A1.ies Absolute 0.90 

For other IES files, please visit www.kenall.com. 




12 

SmartSense Lens selection. 

WARRANTY: Limited ten (10) year warranty. Polycarbonate lens required for 

Peace of Mind Guarantee ® . 


LISTINGS: Luminaire is certified to UL Standards 1598 and 8750 by Intertek Testing 

23.00" 

DRILLING TEMPLATE 

TopDek 3.00" 

Laboratory for Wet Location. IP65 per IEC 60598. IESNA-designated full cut-off. 

Ø 

21.07" 

Ordering Information 

IDA-Approved Dark-Sky Friendly Fixture. Luminaire is 2G tested for vibration per 

ANSI C136.31. Photometry tested to the IESNA LM-79-08 standard by an ILAC/ISO17025 

Ø.49"(2) 

.88" 

Ø .49"(2) 

3.00" 

3.00" 

18.50" 

accredited laboratory. Product listed on Designlights Consortium QPL. 

1.50" 

Catalog Number Example For TopDek 1.50" 

NOTE: -40ºC to 40ºC ambient temperature rated unless otherwise noted. 

Pole Mount Luminaires 

The (See following photometric data chart for light demonstrates output reductions catalog higher ambient number temperatures). logic. Consult specification sheets for complete offerings, options and accessories. 

1.81" 

Example: TPD23-3HSS-TP-DB-216L57K-DV-BSPK-SS4020 

35.90" 

Ø .88" 

BOTTOM VIEW 

20.50" 

6.10" 8.30" 

ORDERING INFORMATION 

Model 

TPD23 

Distribution Type 

2 Type II 

3 Type III 

3HSS Type III with House-side Shield 

4 Type IV 

5S Type V – Wide Square 

5N Type V – Narrow Round 

Lens Type 

TP • Textured Clear Polycarbonate 

TA Textured Clear Acrylic 

Finish 

DB Dark Bronze 

GW Gloss White 

LG Light Gray 

MB Matte Black 

CC Custom Color 

Dist. Type 

23.00" 

Lens Type Finish Lamp Type Voltage Options 

Lamp Type 

Voltage 

100L40K* 100 21.07" Watt 4000K LED DV 120-277 Volts 

100L50K* 100 Watt 5000K LED 347 347 Volts 


160L40K 160 Watt 4000K LED 

160L50K 160 Watt 5000K LED 

160L57K 160 Watt 5700K LED 

Options 

BSPK Birdspikes 

216L40K 216 Watt 4000K LED CBEA** CBEA Specification Compliance 

216L50K 216 Watt 5000K LED FS Single Fuse & Holder 

216L57K 216 Watt 5700K LED R80 Minimum 80 CRI Lamp 

(4000K only) 

RPC Receptacle for Photocell, Shorting 

Cap, etc. 

SSIS t SmartSense Individual Sensor 

(click here for specifications) 

SSOS t SmartSense Only Sensor 

(click here to specify required 

Control Module) 

35.90" 

SmartSense Lens Accessories Mounting 

6.10" 8.30" 

SmartSense Lens (Coverage Dia. × Mounting Height) 

SS4020† 40' Dia. × 20' Ht. 

SS6040† 60' Dia. × 40' Ht. 

Accessories 

WMA Wall Mount Adapter 

TMA s Tenon Mount Adapter (fits 2 3/8" vertical tenons) 

Mounting Configurations for TMA Accessory only 

(See page 2 for selections) 

S1 Single 

23.00" 

TW90 Twin at 90° 


TR90 Triple at 90° 


Q90 Quad at 90° 

21.07" 

• Required for Peace of Mind Guarantee ® 

* 55°C maximum ambient temperature 

** Includes additional warranty benefits 

t 

SmartSense Lens required 

† SSIS or SSOS required 

s 

Must select mounting configuration (See page 2) 

3.00" 

3.00" 

Versatility in Design & Function 

Versatility in design and function make TopDek an ideal lighting solution for a variety of parking deck and surface lot configurations. 

TopDek provides flexibility to shape, direct and distribute patterns of light by utilizing a range of IES distributions pictured below. 

Available with an integrated house side shield, TopDek offers distributions that are ideal for applications with light trespass concerns. 

Distribution Options: 

www.kenall.com P: 800-4-Kenall F: 847-360-1781 1020 Lakeside Drive Gurnee, Illinois 60031 

When you see this image, you will know the Kenall product shown or described is designed and manufactured in the USA with components purchased from US suppliers, 

and meets the Buy American requirements under the ARRA. Kenall has not determined the origin of its domestically purchased components or the subcomponents thereof. 

Content of specification sheets is subject to change; please consult www.kenall.com for current product details. © 2013 Kenall Mfg. Co. All rights reserved. 

TPD23-060413 

Type II (2) Type III (3) Type IV (4) 

Type III (3HSS) 

House Side Shield 

Type V (5N) 

Narrow Round 

Type V (5S) 

Wide Square 

For other distribution types, consult factory. 




TopDek Wind Loading Map 


Luminaire Effective Projected Area (EPA) 

EPA Outdoor Wind Load Calculations 

A fixture's Effective Projected Area (EPA) is equal to the area 'visible' by the wind at a particular angle. All poles have maximum weight and 

EPA capacities that the luminaires mounted to them must not exceed. These capacities are based on the wind zone in which the luminaires 

are located. Below is a list of fixture and mounting bracket EPA values for various TopDek configurations. 

13 

SINGLE TWIN @ 90° TWIN @ 180° TRIPLE @ 90° TRIPLE @ 120° QUAD @ 90° 

Standard Unit 0.81 ft 2 1.34 ft 2 1.62 ft 2 2.32 ft 2 2.10 ft 2 2.32 ft 2 

Unit w/SmartSense Micro 0.91 ft 2 1.38 ft 2 1.82 ft 2 2.32ft 2 2.10 ft 2 2.32 ft 2 

Note: Kenall's optional HSS house-side shield is internal and does not affect EPA. 

Wind Speed's Impact on Luminaire Selection 

The wind loading map of the U.S. (pictured below) can be used to select the appropriate lighting fixtures and poles, based on EPA ratings, 

for parking decks in specific geographic locations. The values on the map can be used to determine whether the configuration under 

consideration will withstand the estimated average wind velocity of a particular region. The total wind load rating for the desired pole must 

be greater than the total combined EPA of the luminaire(s). 

Washington 

Montana 

North Dakota 

Maine 

Oregon 

California 

Nevada 

Idaho 

Utah 

Wyoming 

Colorado 

South Dakota 

Nebraska 

Kansas 

Minnesota 

Iowa 

Missouri 

Wisconsin 

Illinois 

Michigan 

New York 

Pennsylvania 

Ohio 

Indiana 

Md. 

West 

Virginia 

Virginia 

Kentucky 

N.H. 

Vt. 

Mass. 

R.I. 

Conn. 

New Jersey 

Delaware 

Arizona 

New Mexico 

Oklahoma 

Arkansas 

Tennessee 

North Carolina 

South 

Carolina 

Mississippi 

Alabama 

Georgia 

Texas 

Louisiana 

Alaska 

Florida 

Wind Speed Legend 

70 

80 

90 

100 

Hawaii 

110 

NOTE: Wind speed map based on ANSI/ASCE 7-93 specifications. The above map contains only large area information. Some areas have microclimates with 

higher or lower wind loading requirements. Consult local codes for specific rules regarding your specific location. 




14 


TopDek Mounting & Installation 

Designed for Ease of Installation and Maintenance 

TopDek ships ready for mounting on round or square poles at least 3" in size from any manufacturer (poles by others), and its clamshell 

design offers hinged access for ease of installation and maintenance. 

Round Pole Mounting 

Square Pole Mounting 

Round Pole 'Ready' 

TopDek ships ready for round pole 

installations. 

Square Pole Adapter Plate 

The adapter plate ships with every unit 

and enables TopDek to be used in square 

pole installations. 

Ø.438 (2) 

3.00 

Ø.438 (2) 

Ø.875 

Ø.875 

3.00 

1.50 

6.00 3.00 

1.50 

DRILL HOLES REQUIRED ON 

Drilling POLE FOR Template MOUNTING. 

1.8125 

Square Pole Adapter 

20.50 

23.00 

32.00 

18.50 

3.20 

7.70 

6.10 

1 | Remove the lower portion of the housing. 

Fasten the upper portion to the pole, using the 

square pole adapter plate if necessary. Feed the 

appropriate wiring through the center opening. 

2 | Slip the bottom portion of the housing onto 

the hinged lip. 

3 | Make all wiring connections using wet 

location wire nuts (by others). 

4 | Swing the lower hinged potion of the fixture 

upward. Secure the lower to the upper portion of 

the housing using the captive screws in the lower 

housing. Installation is complete. 




TopDek & SmartSense Micro 

For Integral Sensing at the Luminaire 


Kenall’s SmartSense Micro control system intelligently monitors both motion and daylight, providing flexible dimming capabilities when 

the space is unoccupied and/or when sufficient ambient daylight levels are detected. Capable of zonal control, SmartSense Micro is autocommissioned 

via a laser pointer, is fully operational within 24 hours, and provides an automatic indication when LED end-of-life (L70) has 

been reached. 

15 

TopDek Individual Control 

This LED-driven luminaire offers an optional SmartSense Micro 

system, which switches the luminaire to full brightness upon 

detecting motion in the space, and slowly dims back to low-level 

standby mode once occupancy is no longer detected. 

TopDek Zonal Control 

Each SmartSense Micro luminaire is equipped with an integrated 

sensor unit. To achieve zonal control, individual luminaires can be 

linked together so that as one unit senses motion or daylight, all 

linked luminaires are brought back to full brightness or dimmed with 

each other. 

Zonal control can also be achieved through the use of the SmartSense 

Control System (see pg. 16), which enables a single occupancy sensor 

to trigger the operation of a single luminaire or up to an entire deck 

of luminaires. 

Integral Sensor 

The SmartSense Micro sensor serves as both a daylight sensing 

photosensor and a passive infrared occupancy sensor with a 

coverage pattern up to 60' in diameter from a 40' mounting height. 

Features 

Feature 

Description 

Occupancy & Daylight Sensing 

SmartSense Micro luminaires intelligently reacts to both motion and daylight. 

Integrated Control 

All controls are built into the luminaire and require no additional equipment to operate in 

individual mode. 

Zonal Control Capability 

Auto-commissioned 

By simply connecting control wires between sensors, SmartSense Micro luminaires can be 

linked together for zonal control. 

SmartSense Micro is auto-commissioned via a laser pointer, and is fully operational within 

24 hours. 

End of Life Monitoring 

SmartSense Micro provides an automatic indication when LED end-of-life (L70) is reached. 




16 


TopDek & SmartSense Control System 

Sensing Occupancy and Daylight for Dramatic Energy Savings with Strategically Located Sensors 

Kenall’s SmartSense control system utilizes an innovative design concept. The system intelligently monitors both motion and daylight from 

strategically located sensors, providing flexible dimming and switching capabilities when the space is unoccupied and/or when ambient 

daylight levels are detected. SmartSense’s ability to dim light levels in response to occupancy and daylight represents cost and energy saving 

opportunities for the facility owner. 

Sensor 

The SmartSense sensor serves as both 

a daylight sensing photosensor and a 

passive infrared occupancy sensor that 

can be strategically located to maximize 

safety and energy savings. 

Control Module 

The SmartSense control module receives input from one 

daylight sensor and up to six total occupancy sensors, 

servicing up to 32 luminaires. It can also be linked with 

additional control modules to control an unlimited number 

of luminaires regardless of the number of sensors used. 

TopDek Luminaire 

This LED-driven luminaire, specifically designed for use 

with the SmartSense control system, will quickly achieve 

full brightness upon detecting motion in the space, and 

will slowly dim back to low-level standby mode once 

occupancy is no longer detected. 

Interconnection 

Sensor Ports 

Dimming Control 

L70 Indicator Light 

Sensor Ports 


Commission 

Dimming Control 

For greater energy savings, the control module is capable of setting 

the low-level standby of the luminaire as low as 20% light output 

(80% dimmed). 

Sensor Ports 

Each control module has the capacity to accept six dual-technology 

sensors-one of which provides daylight level input. Each bay has a 

green LED indicating power to the sensor and a red LED indicating 

occupancy. 


The control system features an “end-of-life” indicator that turns red 

when the TopDek luminaires reach L70, which is 70% of the initial 

lumen output. 

24-Hr. Self-Commissioning Button 

This feature automatically commissions the control system with the 

touch of a button. The control module measures the light levels 

during a 24-hour cycle and eliminates the need for expensive field 

commissioning. 

Interconnection 

Interconnect multiple control modules to expand the number 

of luminaires in a zone. Each control module can operate up 

to 32 luminaires. 




SmartSense Control System Layout 

System Analysis and Operational Benefits 


The Kenall SmartSense Control System provides intelligent parking deck and surface lot automation without the typical expense of more 

traditional control systems. Luminaires will remain in low level standby mode until occupants pass by a sensor located at the vehicular or 

pedestrian entry point. Kenall recommends that dimmed light levels meet IES recommendations. The system will immediately raise levels to 

the maximum light output of the luminaires when occupants enter the parking deck or surface lot and will remain at those levels until the 

system time-out period has elapsed (adjustable from 30 seconds to 30 minutes). 

17 

Sensors 

Sensors are dual capability devices with the ability 

to detect and adjust to occupancy and daylighting. 

The sensors must be located in a covered area, and 

the standard sensor range is 40' diameter from a 20' 

mounting height or 60' diameter from a 40' height 

(other lens options are available). 

Note: In this layout, the sensor is positioned on the 

ramp ceiling leading up to the top of the deck. 

Control Module 

The main operational control device receives input 

from occupancy/daylight sensors and actuates the 

luminaires within the zone based on sensor input. 

The system also allows multiple control modules to be 

interconnected. 

TopDek Luminaires 

Multiple units can be switched and dimmed 

simultaneously. The luminaires are controls-ready, 

requiring no additional equipment for connection to 

the control module and sensors. 

This sensor is located on 

the ramp ceiling leading up 

to the top of the deck. 

Configurations can be designed where 

a single occupancy sensor triggers the 

operation of either a single luminaire to an 

entire deck of luminaires. When daylight 

contribution is present, the system will 

continuously dim the luminaires to maintain 

desired light levels. Sensors can supply 

daylight and occupancy information to a 

single zone or multiple zones as required. 

The sensors and control modules must 

be positioned in a covered location at all 

points of vehicular and pedestrian egress. 




18 


TopDek & SmartSense Savings & Sustainability 

Combining Premiere Lighting Performance & Energy Savings 

Kenall Manufacturing is committed to the economic and sustainable benefits inherent to LED technology as 

evidenced by the widespread use of LED products we manufacture. As a combined system, Kenall’s new TopDek 

luminaire and SmartSense controls provide an opportunity for savings in the parking garage environment. 

With a focus on energy, resource conservation, and the reduction of hazardous waste, the new TopDek line: 

• Boasts an energy efficient design 

• Utilizes eco-friendly, long-lasting LEDs 

• Is constructed of lead and mercury free materials, and emits no harmful UV radiation 

• Offers full cutoff distribution and an IDA-Approved Dark Sky Friendly designation 

• Qualifies for a variety of rebate and tax incentive programs by the U.S. Department of Energy, and various States, 

Municipalities, and Utilities 

• Meets the Buy American Act requirements under the American Recovery & Reinvestment Act (ARRA) 

In support of our ‘go green’ initiative, we have established partnerships with the United States Green Building Council, Design Lights 

Consortium, and the United States Environmental Protection Agency / Energy Star Program. 





19 




20 


Complementary Parking Garage Products 

Kenall offers a comprehensive family of luminaires to address a full range of parking garage lighting needs. For the interior of the garage, 

we offer TekDek LED with SmartSense controls. TekDek's high efficacy illumination can be combined with Kenall's SmartSense control system 

to provide cost and energy savings, with payback occurring in as little as 14 months. For stairwells and points of egress, Kenall offers our 

Millenium Stretch and Millenium Metrex families. 

TopDek 

Parking Deck Lighting 

TekDek 

Parking Deck Lighting 

Millenium Auracyl 

Architectural Sconce 





21 

Millenium Metrex is a complete line of exit and emergency lighting to ensure patron safety and wayfinding. Millenium Stretch is a linear series 

available with long-life fluorescent or LED lamp options that can be tied into the SmartSense controls or integrated daylighting/occupancy 

control systems to meet the needs of any stairwell installation. And finally, Kenall's Millenium Auracyl sconces provide smooth, gentle lines to 

complement virtually any building exterior. While Millenium Auracyl's rugged design and durable construction are ideal for high abuse public 

areas, it is available in 15 decorative frame styles for added flair and personality and is covered by Kenall's Peace of Mind Guarantee. 

Millenium Metrex 

Emergency Egress 

Millenium Stretch 

Stairwell 




22 


TopDek Warranties & LED Listings 

Warranty 

The TopDek LED product is warranted by Kenall to be free of 

defects in workmanship and materials for a period of one (1) year 

from the date of invoice. Kenall warrants LED lamps and internal 

power regulation components for a period of five (5) years from 

the date of invoice against defects in materials and workmanship 

that result in a fixture lumen depreciation of 30% or greater. Lumen 

depreciation is compared to the published lumen output of the 

product on the date of manufacture per IESNA LM-79 reporting 

procedures. Normal accumulation of particulates on the optical 

surfaces shall not be factored into the lumen depreciation. 

Kenall is pleased to be able to offer our exclusive Peace of Mind 

Guarantee ® on the TopDek luminaire. When using a polycarbonate 

lens and installed according to our instructions, Kenall will repair or 

replace any fixture rendered inoperable due to physical abuse for the 

life of the product installation. 

The SmartSense Control System is warranted by Kenall to be free 

of defects in workmanship and materials for a period of one (1) year 

from the date of invoice. 

Optional CBEA Warranty: Five year warranty on defects in 

workmanship and material, LED lamps and power regulation, paint 

finish (chipping/cracking/fading), color shift greater than .007 

(CIE1976). 

Kenall reserves the right to issue credit, repair, or replace the 

defective merchandise, at its discretion, upon notification and 

confirmation by its local representative of the defect. Kenall also 

reserves the right to test and examine the defective product if the 

defect is questionable, and to deny the warranty herein for any 

product altered, improperly installed, or installed in applications 

for which it is not intended. This includes operation in ambient 

temperatures above stated limits for any length of time. Failure by 

electrical surge shall not be covered under warranty. 

Kenall assumes no responsibility for labor or freight costs incurred in 

connection with the installation, removal, or replacement of products 

determined to be defective or any other consequential or incidental 

damages arising from the use of the product. Kenall’s entire liability 

on any claim of loss or damage resulting from a defective product is 

limited to the replacement price of the product. 

Led Lighting Facts ® — Department of Energy LED 

Quality Advocate Program For Led Luminaires 

As a member of the Department of Energy's LED Quality Advocates, 

Kenall Manufacturing has pledged to include the Lighting Facts 

label in conjunction with our LED luminaires. The label reports 

product performance results in five areas from actual test data* 

in accordance with industry standards measuring photometric 

performance of LEDs: 

• Luminaire light output 

• Efficacy (lumens per watt) 

• Measured power (watts) 

• Correlated Color Temperature 

• Color Rendering Index 

Kenall Manufacturing is a registered Lighting Facts Product Partner. 

For more information about this program or for copies of our 

Lighting Fact Labels please contact Kenall at info@kenall.com, or 

visit us on the web at www.kenall.com. 

* Luminaire measurements have been standardized with the 

issuance of the IESNA Standard LM-79-2008 test procedure. 

Kenall's ISO/IEC Accredited Photometric Lab 

Expedites Design Lights Consortium (DLC) Listings 

Kenall's state-of-the-art photometric lab has passed the most 

stringent proficiency testing in the industry to become ISO/IEC 

17025 accredited. In doing so, we have earned the prestigious 

credentials for both the Department of Energy's Lighting Facts ® 

listings and Design Light Consortium approvals, as well as EPA 

recognition for Energy Star. This accreditation enables us to 

submit multiple LED listings in multiple colors with the benefit of 

shortened lead times. 




TOPDEK LED 

Luminaires for Parking Garages & Surface Lots 

TPD SERIES 

IP65 LED 

20.50" 


PROJECT INFORMATION 

Job Name 

20.50" 

Fixture Type 

35.90" 35.90" 

32.00" 32.00" 

23 

Catalog Number 

PRODUCT FEATURES: 

» Pole-mounted LED area light; 23" Diameter 

» Concealed heatsink fins for optimized 

thermal management 

» Full-Cutoff; IDA Dark-Sky Compliant 

18.50" 

18.50" 

20.50" 

Approved by 

TOP VIEW 

35.90" 

32.00" 

20.50" 

3.20" 

20.50" 

3.20" 

SPECIFICATIONS: 

HOUSING: Marine grade die-cast aluminum. Integral heatsink with concealed 18.50" convection 

fins. TGIC polyester powder coat finish with 5-step pre-treatment. Salt spray test: 1,000 

hours. See Ordering Information for available finishes. Closed-cell silicone gasketing at all 

housing interfaces. 

MOUNTING: Compatible with 3"-6" square steel or aluminum poles, 3"-6" tapered 

and non-tapered round steel or aluminum poles. Poles by others. All structural hardware 

304 stainless steel, or zinc plated steel Grade 8. 

OPTICS: Type II, III, IV, V-Narrow Round and V-Wide Square roadway classifications 

available. Full-cutoff classification. Asymmetric option available with house-side 20.50" shield. 

High impact resistant, injection molded clear textured UV-stabilized polycarbonate lens. 

ELECTRICAL: Replaceable high-brightness ANSI 4000K, 5000K, and 5700K white LED 

array. 65 CRI min. See Options for higher CRI lamp availability. 120-277VAC, 347VAC or 

480VAC, 50/60Hz input with replaceable high power factor electronic constant-current 

driver (0.95 PF). Minimum 18.50" 85% driver efficiency. EMC meets or exceeds 

FCC CFR Part I5. Standard 20KV/KA surge protection to IEEE/ANSI C62.41.2 C High 

(10KV for 347 VAC). 

SMARTSENSE : SmartSense Individual Sensor (SSIS) provides individual luminaire 

control via an integral control module and occupancy/light level sensor. SmartSense 

Only Sensor (SSOS) option provides an integral occupancy/light level sensor but must 

be connected to a remote SSCS Control Module. See Ordering options for required 

SmartSense Lens selection. 

WARRANTY: Limited ten (10) year warranty. Polycarbonate lens required for 

Peace of Mind Guarantee ® . 

LISTINGS: Luminaire is certified to UL Standards 1598 and 8750 by Intertek Testing 

Laboratory for Wet Location. IP65 per IEC 60598. IESNA-designated full cut-off. 

IDA-Approved Dark-Sky Friendly Fixture. Luminaire is 2G tested for vibration per 

ANSI C136.31. Photometry tested to the IESNA LM-79-08 standard by an ILAC/ISO17025 

accredited laboratory. Product listed on Designlights Consortium QPL. 

NOTE: -40ºC to 40ºC ambient temperature rated unless otherwise noted. 

(See photometric data for light output reductions at higher ambient temperatures). 

23.00" 

21.07" 

23.00" 

21.07" 

3.00" 

3.00" 

FRONT VIEW 

OPTIONAL 

OCCUPANCY SENSOR 

23.00" 

21.07" 

DRILLING TEMPLATE 

Ø.49"(2) 

Ø.88" 

1.50" 

35.90" 

32.00" 

3.00" 

3.00" 

3.00" 

3.00" 

20.50" 

3.00" 

18.50" 

1.81" 

3.00" 

3.00" 

Ø.49"(2) 

Ø.88" 

1.50" 

SIDE VIEW 

Ø.49"(2) 

Ø.88" 

35.90" 

Ø .49"(2) 

1.50" 

3.20" 

1.50" 

35.90" 

Ø .88" 

3.00" 

Ø.49"(2) 

Ø.88" 

3.00" 

1.50" 

20.50" 

35.90" 

BOTTOM VIEW 

1.81" 

Ø .49"(2) 

3.20" 

3.00" 

1.50" 

Ø .88" 

1.81" 1.81" 

Ø .49"(2) 

Ø .88" 

Ø .49"(2 

1.50" 

Ø .88 

1.50" 6.10" 8.30" 6.10" 8. 

20.50" 

6.10" 8.30" 

ORDERING INFORMATION 

Model 

TPD23 

Distribution Type 

2 Type II 

3 Type III 

3HSS Type III with House-side Shield 

4 Type IV 

5S Type V – Wide Square 

5N Type V – Narrow Round 

Lens Type 

TP • Textured Clear Polycarbonate 

TA Textured Clear Acrylic 

Finish 

DB Dark Bronze 

GW Gloss White 

LG Light Gray 

MB Matte Black 

CC Custom Color 

Dist. Type 

23.00" 

Lens Type Finish Lamp Type Voltage Options 

Lamp Type 

Voltage 

100L40K* 100 21.07" Watt 4000K LED DV 120-277 Volts 



160L40K 160 Watt 4000K LED 

160L50K 160 Watt 5000K LED 

160L57K 160 Watt 5700K LED 

Options 

BSPK Birdspikes 

216L40K 216 Watt 4000K LED CBEA** CBEA Specification Compliance 

216L50K 216 Watt 5000K LED FS Single Fuse & Holder 

216L57K 216 Watt 5700K LED R80 Minimum 80 CRI Lamp 

(4000K only) 

RPC Receptacle for Photocell, Shorting 

Cap, etc. 

SSIS t SmartSense Individual Sensor 

(click here for specifications) 

SSOS t SmartSense Only Sensor 

(click here to specify required 

Control Module) 

35.90" 

SmartSense Lens Accessories Mounting 

6.10" 8.30" 

SmartSense Lens (Coverage Dia. × Mounting Height) 

SS4020† 40' Dia. × 20' Ht. 

SS6040† 60' Dia. × 40' Ht. 

Accessories 

WMA Wall Mount Adapter 

TMA s Tenon Mount Adapter (fits 2 3/8" vertical tenons) 

Mounting Configurations for TMA Accessory only 

(See page 2 for selections) 

S1 Single 

23.00" 





Q90 Quad at 90° 

21.07" 

• Required for Peace of Mind Guarantee ® 

* 55°C maximum ambient temperature 

** Includes additional warranty benefits 

t 

SmartSense Lens required 

† SSIS or SSOS required 

s 

Must select mounting configuration (See page 2) 

3.00" 

3.00" 

www.kenall.com P: 800-4-Kenall F: 847-360-1781 1020 Lakeside Drive Gurnee, Illinois 60031 

When you see this image, you will know the Kenall product shown or described is designed and manufactured in the USA with components purchased from US suppliers, 

and meets www. the Buy kenall.com American requirements P: under 800-4-Kenall the ARRA. Kenall has Email: not determined info@kenall.com the origin of its domestically 1020 Lakeside purchased Drive components Gurnee, or Illinois the subcomponents 60031 thereof. 

Content of The specification Kenall product sheets shown is subject on to this change; page is please designed consult and www.kenall.com manufactured in for the current USA with product components details. © 2013 purchased Kenall from Mfg. US Co. suppliers, All rights and reserved. meets the Buy 

American requirements under the ARRA. Kenall has not determined the origin of its domestically purchased components or the subcomponents thereof. 

TPD23-060413

24 


1020 Lakeside Drive 

Gurnee, Illinois 60031 

847-360-8200 

FAX 847-360-1781 

www.kenall.com 

©2012 Kenall Mfg. ¯¯Co. 

All rights reserved. 

L10044-091312

Kenall_TopDek

Create successful ePaper yourself

Delete template?

Save as template?