Type 4300 Catalogue - GMM Pfaudler Ltd
Type 4300 Catalogue - GMM Pfaudler Ltd
Type 4300 Catalogue - GMM Pfaudler Ltd
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
140<br />
10 11<br />
12 pH<br />
140<br />
10 11<br />
12 13 pH<br />
220<br />
120<br />
0.5 mm/year<br />
0.2 mm/year<br />
120<br />
0.5 mm/year<br />
220<br />
180<br />
C<br />
100<br />
80<br />
0.1 mm/year<br />
Fully Resistant<br />
60<br />
0.001 0.01 0.1 0.5 1 5 10<br />
% Na2CO 3 by Weight<br />
Volume to Surface Area Ratio (V/O) = 20<br />
C<br />
100<br />
80<br />
0.2 mm/year<br />
0.1 mm/year<br />
Fully Resistant<br />
60<br />
0.001 0.01 0.05 0.1 0.5 1 5 10 20<br />
% NH by Weight<br />
3<br />
Volume to Surface Area Ratio (V/O) = 20<br />
C<br />
180<br />
140<br />
100<br />
60<br />
0.5 mm/year<br />
0.2 mm/year<br />
0.1 mm/year<br />
Fully Resistant<br />
20 40 60 80 100<br />
C<br />
140<br />
100<br />
60<br />
40<br />
0.5<br />
mm/year<br />
0.1 mm/year<br />
Fully Resistant<br />
0.2<br />
mm/year<br />
20 40 60 80 100<br />
% H SO by Weight<br />
2 4<br />
Volume to Surface Area Ratio (V/O) = 20<br />
% H PO by Weight<br />
3 4<br />
Volume to Surface Area Ratio (V/O) = 20<br />
<br />
<br />
<br />
<br />
C<br />
200<br />
180<br />
160<br />
140<br />
120<br />
100<br />
80<br />
60<br />
10<br />
0.5 mm/year<br />
0.2 mm/year<br />
0.1 mm/year<br />
Fully Resistant<br />
20 30<br />
% HCL by Weight<br />
Volume to Surface Area Ratio (V/O) = 20<br />
C<br />
200<br />
180<br />
160<br />
140<br />
120<br />
100<br />
80<br />
0.5 mm/year<br />
0.2 mm/year<br />
0.1 mm/year<br />
Fully Resistant<br />
20 40<br />
60<br />
% HNO by Weight<br />
3<br />
Volume to Surface Area Ratio (V/O) = 20<br />
C<br />
220<br />
200<br />
180<br />
160<br />
140<br />
120<br />
0.5 mm/year<br />
0.2 mm/year<br />
0.1 mm/year<br />
Fully Resistant<br />
20 40 60 80 100<br />
% CH COOH by Weight<br />
3<br />
Volume to Surface Area Ratio (V/O) = 20<br />
Although <strong>Type</strong> <strong>4300</strong> glass has a high degree of helpful compressive<br />
stress in the glass layer, there are definite limits to the level of thermal<br />
stress which the glass can withstand without incurring damage.<br />
Only two conditions must be considered when determining the<br />
temperature limits:<br />
A. Introduction of media into a vessel. The limits are determined from<br />
Chart A (located on next page).<br />
B. Introduction of media into a jacket. The limits are determined from<br />
Chart B (located on next page).<br />
In both cases the safe operating range lies within the polygons as<br />
outlined on the charts. The left and right sides on the polygons represent,<br />
respectively, the minimum and maximum wall temperatures allowed. The<br />
bottom and top on the polygons represent, respectively, the minimum<br />
and maximum product temperatures allowed (Chart A) and the minimum<br />
and maximum jacket temperatures allowed (Chart B).<br />
With Chart B, it is also necessary to know the heat transfer film<br />
coefficient of the jacket media. Three curves are shown : one for steam<br />
2 2<br />
(8500 Wm K) and two for typical heating oils (1500 and 1000 Wm K).<br />
CAUTION : “Safe” operating temperatures vary with conditions.<br />
Because so many variables are involved, temperature ranges are<br />
given only as a guide. When practical, operation below the<br />
maximum and above the minimum is recommended. Contact<br />
<strong>Pfaudler</strong> for details.