KÖSTER Adex
KÖSTER Adex
KÖSTER Adex
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
KÖSTER ® <strong>Adex</strong><br />
Cementitious bonding agent and reinforcement corrosion protection<br />
Product Description:<br />
KÖSTER <strong>Adex</strong> is a cement based, factory<br />
blended mix of corrosion inhibiting chemicals,<br />
polymers and selected fillers in cement,<br />
powder form.<br />
The powder is mixed with water to form a<br />
brushable slurry. The slurry is applied on<br />
mineral substrates and reinforcement steel<br />
for bonding and corrosion protection.<br />
Technical Data :<br />
Appearance, color Powder, grey<br />
Application<br />
temperature<br />
+5 to +30 0 C<br />
Potlife 20 min<br />
Adhesion > 2 N / mm 2<br />
Compressive<br />
strength<br />
27,0 N / mm 2 [EN 196-1]<br />
Flexural strength 6,4 N / mm 2 [EN 196-1]<br />
Mixing ratio 0,22 lt water / kg powder<br />
Density<br />
Advantages :<br />
Powder = 1,285 gr/cm 3<br />
Fresh mortar = 2,0 gr/cm 3<br />
• Excellent adhesion on mineral substrates<br />
and steel<br />
•<br />
• Easy to use – mix with water only<br />
• Easy application – brush or spray<br />
• No special tools are needed<br />
• Not toxic<br />
Instructions:<br />
Job Conditions - Air and surface<br />
temperature for application of KÖSTER <strong>Adex</strong><br />
slurry must be 5 °C to 30 0 C and must<br />
remain so for a minimum of 24 hours.<br />
Temporary Protection - Shall be provided<br />
at all times until the material is fully cured.<br />
Surface Preparation - The surface has to<br />
be sound and solid, free of laitance, paint,<br />
dust, form oil and other contaminants that<br />
might affect the bonding adversely. Suitable<br />
tools are wire brushes, high-pressure water<br />
jets, sand and shot blasting.<br />
Steel surfaces must be free of rust, optimum<br />
degree of cleaning is SA 2.<br />
Mineral substrates must be damped before<br />
application of KÖSTER <strong>Adex</strong> slurry.<br />
Mixing – One bag ( 25 kg ) of KÖSTER <strong>Adex</strong><br />
should be mixed with 5,5 lt of clean water.<br />
The powder should always be added to the<br />
water slowly and during continuous mixing<br />
action with power mixer equipped with<br />
mixing paddle.<br />
Application – Apply the sealing slurry with<br />
a firm brush or a suitable spraying device.<br />
Allow every coat to dry completely before<br />
applying the next one.<br />
Do not apply layers thicker than 1,0 mm in a<br />
single coat.<br />
Consumption :<br />
1mm thickness (apr. 2,0 kg/m 2 )<br />
Cleaning of tools :<br />
Clean tools with water while KÖSTER <strong>Adex</strong> is<br />
still wet<br />
Before use, please check that this is the actual edition of the Technical Data Sheet. The information contained in this Technical Data Sheet is of a<br />
general nature and is provided in good faith and we accept no liability for errors or omissions. Because use and application of this product are out<br />
of our control and depend, concerning substrate, load and method of application, on the particularities of the individual case, our advice, verbal,<br />
written or based on tests, does not exempt the applicator from testing the suitability of the products for the intended use.
Packaging :<br />
25 kg bag<br />
Storage :<br />
Dry and at room temperature, in original<br />
containers.<br />
Shelf life :<br />
12 months.<br />
Caution :<br />
Contains cement.<br />
Avoid contact with skin and eyes. Wear<br />
suitable protective clothing, gloves and eye /<br />
face protection. After contact with skin, wash<br />
immediately with plenty of water and soap.<br />
In case of contact with eyes, rinse<br />
immediately with plenty of water and seek<br />
medical advice. For additional references to<br />
safety-hazard warnings, regulations<br />
regarding the transport and waste<br />
management please refer to the<br />
relevant Material Safety Data Sheet.<br />
Before use, please check that this is the actual edition of the Technical Data Sheet. The information contained in this Technical Data Sheet is of a<br />
general nature and is provided in good faith and we accept no liability for errors or omissions. Because use and application of this product are out<br />
of our control and depend, concerning substrate, load and method of application, on the particularities of the individual case, our advice, verbal,<br />
written or based on tests, does not exempt the applicator from testing the suitability of the products for the intended use.