EN-2011 elements basics extras

RITMATO 14 Vertical
The RITMATO 14 Vertical model is a radiator created with 14 mm diam. vertical tubular steel
elements featuring groups of heating elements alternated with gaps (every gap corresponds
to an empty space hypothetically taken up by a certain number of elements which however
are not welded on - see detail).
This model is available both in single version column (RV14) and double double version
column (RV14D)
NOTES and LIMITS
For heights over 150 cm special reinforcing spacers are applied between the elements, the
welding position of the reinforcing spacer is specified in page 203.
This model is created with heights (H) from 110 cm to 280 cm.
PRICE CALCULATION
The price of the RITMATO radiator is the same as the price of model CV14-CV14D with the
same dimensions (H x number of elements) considering the empty spaces as taken up (no
matter how many elements are missing)
SPECIAL VERSIONS
This model can be made in special versions such as for example, uninterrupted sequence
and/or in curved version and other. For further information regarding feasibility according to
your needs contact our technical department, which will examine the request and, in the
case of feasibility, will supply you with detailed drawings and cost estimate.
HOW TO ORDER
To order an RV14 proceed as follows (see detail on the side):
- put the MODEL code RV14
- specify the HEIGHT requested e.g. 200 cm
- specify the TOTAL elements e.g. 24 elements
- specify the type of CONNECTOR e.g. 0C1
- choose the SUPPORT e.g. ST
- choose the COLOUR e.g. White RAL 9010
- specify SEQUENCE CODE e.g. 6-3-6-3-6
Correct code
RV14 - H. 200 cm - 24 elem. – 0C1 Conn. - ST Supp. - Ral 9010 – Sequence 6-3-6-3-6
EXAMPLE AS SHOWN IN THE DRAWUNG ON THE SIDE (H.= 200 cm)
SEQUENCE CODE
Uninterrupted sequence 6.3.6.3.6
REFERENCE TABLE
for THERMAL YIELD and HEIGHT CALCULATION see CV14 table in page 67.
WIDTH CALCULATION
total elements 6+3+6+3+6 = 24 elements (L=58,6 cm)
THERMAL YIELD CALCULATION
heating elements 6 + 6 + 6 = 18 elements (Watts 1060 x H=200 cm)
PRICE CALCULATION
total elements 6+3+6+3+6 = 24 elements (Price=€ 359,00 x H=200 cm)
CONNECTORS
The RV14 and RV14D models are always supplied with “0C1”. connectors
Should different connectors be required, such connectors must be strictly specified in the order.
In the case of “0B2” connectors, the radiator can be equipped with 2 1/8” chrome-plated plugs on the head of the manifolds.
Standard connectors
standard connector always supplied,
if not otherwise specified in the order
Connectors on request
Connectors available on request WITHOUT any additional charge
78
0C1
Inter-axis =
L + 8,8 cm
S
S
Custom-made connectors
Connectors available on request WITH additional
charge of € 51,00
0B2
0S1
Attacchi speciali
0D1
MS1
(attacchi disponibili a richiesta CON supplemento di prezzo)
Inter-axis =
H - 3,4 cm
S
Inter-axis =
H - 3,4 cm
Inter-axis =
L - 5,8 cm
S
S
single pipe
MD1
S
L
H min.
110 cm
6 3 6 3 6
Custom-made connectors
Connectors available on request WITH additional
charge of € 51,00
d i
B2M
Specify “d” and “i”
HEATING elements
NO elements (gaps)
= Position of connectors
78
50
Watt = Kcal/h ÷ 0,860
Kcal/h = Watt x 0,860
45 56
RV14 RV14D
78
50
22
RV14 RV14D
S = Air Vent I = Inter-axis between connectors
RITMATO 14 Horizontal
The RITMATO 14 Horizontal model is a radiator created with 14 mm diam. horizontal
tubular steel elements featuring groups of heating elements alternated with gaps (every
gap corresponds to an empty space hypothetically taken up by a certain number of
elements - see detail).
This model is available both in single version column (RO14) and double double version column
(RO14D)
NOTES and LIMITS
For widths over 150 cm special reinforcing spacers are applied between the elements. The
welding position of the reinforcing spacer is specified in page 203.
This model is created with widths (L) from 110 cm to 280 cm.
PRICE CALCULATION
The price of the RITMATO radiator is the same as the price of model CO14-CO14D with
the same dimensions (L x number of elements) considering the empty spaces as taken up
(no matter how many elements are missing)
SPECIAL VERSIONS
This model can be made in special versions such as for example, uninterrupted sequence and/
or in curved version and other. For further information regarding feasibility according to your
needs contact our technical department, which will examine the request and, in the case of
feasibility, will supply you with detailed drawings and cost estimate.
HOW TO ORDER
To order an RO14 proceed as follows (to better comprehension refer to the detail in
page78):
- put the MODEL code RO14
- specify the WIDTH requested e.g. 200 cm
- specify the TOTAL elements e.g. 24 elements
- specify the type of CONNECTOR e.g. 0B1
- choose the SUPPORT e.g. ST
- choose the COLOUR e.g. White RAL 9010
- specify SEQUENCE CODE e.g. 6-3-6-3-6
Correct code
RO14 - L. 200 cm - 24 elem. - 0B1 Conn. - ST Supp. - Ral 9010 - Sequence 6-3-6-3-6
EXAMPLE AS SHOWN IN THE DRAWUNG IN PAGE 78 (L.= 200 cm)
SEQUENCE CODE
Uninterrupted sequence 6.3.6.3.6
REFERENCE TABLE
for THERMAL YIELD and HEIGHT CALCULATION see CO14 table in page 71.
HEIGHT CALCULATION
total elements 6+3+6+3+6 = 24 elements (H=58,6 cm)
THERMAL YIELD CALCULATION
heating elements 6 + 6 + 6 = 18 elements (Watts 1222 x L=200 cm)
PRICE CALCULATION
total elements 6+3+6+3+6 = 24 elements (Price=€ 361,00 x L=200 cm)
Watt = Kcal/h ÷ 0,860
Kcal/h = Watt x 0,860
CONNECTORS
The RO14 and RO14D models are always supplied with “0B1”. connectors
Should different connectors be required, such connectors must be strictly specified in the order. IMPORTANT: the connectors of towel warmers and radiators connected to
the same system should all be the same, because different connections could cause operating problems.
Standard connectors
standard connector always supplied,
if not otherwise specified in the order
0B1
Inter-axis =
L - 3,4 cm
MS2
S
S
MD2
S
0S2
Connectors on request
Connectors available on request WITHOUT any additional charge
vertical single pipe
Custom-made connectors
Connectors available on request WITH additional
charge of € 51,00
Inter-axis =
H - 5,8 cm
S
S
0D2
Inter-axis =
H - 5,8 cm
0C2
Inter-axis =
L + 11,8 cm
S
45
56
H
i
d
= Position of connectors
L
min. 110 cm
Custom-made connectors
Connectors available on request WITH additional
charge of € 51,00
S2M D2M
Specify “d” and “i”
i
d
RO14
RO14D
69
41 24
RO14
80
52 24
RO14D
S = Air Vent I = Inter-axis between connectors
79