17.11.2012 Views

X75 Aluminium Flap Valve Pump Design Level 7 - Blagdon Pump

X75 Aluminium Flap Valve Pump Design Level 7 - Blagdon Pump

X75 Aluminium Flap Valve Pump Design Level 7 - Blagdon Pump

SHOW MORE
SHOW LESS

Create successful ePaper yourself

Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.

IMPORTANT SAFETY<br />

INFORMATION Take action to prevent static<br />

sparking. Fire or explosion<br />

can result, especially when<br />

handling flammable liquids.<br />

The pump, piping, valves,<br />

IMPORTANT containers or other miscellaneous equipment<br />

must be grounded. (See page 10)<br />

Read Read these safety warnings warnings<br />

and instructions in in this<br />

manual manual completely, before<br />

WARNING<br />

installation installation and start-up<br />

of the pump. It is the responsibility of the the<br />

This pump is pressurized<br />

purchaser purchaser to retain this manual for reference.<br />

internally with air pressure<br />

Failure to comply with with the recommendations<br />

during operation. Always<br />

stated in this manual manual will damage the pump,<br />

make certain that all bolting<br />

and void void factory warranty.<br />

is in good condition and<br />

that all of the correct<br />

bolting is reinstalled during assembly.<br />

CAUTION<br />

Before pump operation,<br />

i n s p e c t a l l g a s k e t e d<br />

fasteners for looseness<br />

caused by gasket creep. Retorque<br />

loose fasteners to<br />

prevent leakage. Follow recommended torques<br />

stated in this manual.<br />

Before maintenance or<br />

repair, shut off the compressed<br />

air line, bleed the<br />

pressure, and disconnect<br />

the air line from the pump.<br />

The discharge line may be<br />

pressurized and must be bled of its pressure.<br />

WARNING<br />

When used for toxic or<br />

aggressive fluids, the pump<br />

should always be flushed<br />

clean prior to disassembly.<br />

WARNING<br />

WARNING Before doing any main-<br />

WARNING<br />

In the event of diaphragm<br />

rupture, pumped material<br />

may enter the air end of the<br />

pump, and be discharged<br />

into the atmosphere. If<br />

pumping a product which is hazardous or toxic,<br />

the air exhaust must be piped to an appropriate<br />

area for safe disposition.<br />

WARNING<br />

tenance on the pump,<br />

be certain all pressure is<br />

completely vented from the<br />

pump, suction, discharge,<br />

p i p i n g , a n d a l l o t h e r<br />

openings and connections. Be certain the air<br />

supply is locked out or made non-operational,<br />

so that it cannot be started while work is being<br />

done on the pump. Be certain that approved<br />

eye protection and protective clothing are worn<br />

all times in the vicinity of the pump. Failure to<br />

follow these recommendations may result in<br />

serious injury or death.<br />

WARNING<br />

Airborne particles and<br />

loud noise hazards.<br />

Wear ear and eye<br />

protection.<br />

RECYCLING<br />

M a n y c o m p o n e n t s o f A O D D p u m p s a r e m a d e<br />

of recyclable materials (see chart on page 12 for material<br />

specifications). We encourage pump users to recycle worn out parts<br />

and pumps whenever possible, after any hazardous pumped fluids<br />

are thoroughly flushed.<br />

x75afvmdl7sm-rev0411 Page 11

Hooray! Your file is uploaded and ready to be published.

Saved successfully!

Ooh no, something went wrong!