You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Page 1 / 4<br />
Certificate number: 07442/D0 BV<br />
File number: ACM 101/102/001<br />
Product code: 1403I<br />
This certificate is not valid when presented without the<br />
full attached schedule composed of 7 sections<br />
www.veristar.com<br />
<strong>TYPE</strong> <strong>APPROVAL</strong> <strong>CERTIFICATE</strong><br />
This certificate is issued to<br />
<strong>IMO</strong> AB<br />
STOCKHOLM - SWEDEN<br />
for the type of product<br />
SCREW PUMPS<br />
Pump Series ACD, ACE, ACE Optiline, ACF, ACG, ACG Optiline,ACP, LPQ, D4 NTBP, LPD, LPE, LPE Optiline<br />
Requirements:<br />
- BUREAU VERITAS Rules for the Classification of Steel Ships<br />
- BUREAU VERITAS Rules for the Classification of Offshore Units<br />
This certificate is issued to attest that BUREAU VERITAS did undertake the relevant approval procedures for the product identified above which<br />
was found to comply with the relevant requirements mentioned above.<br />
This certificate will expire on: 19 Oct 2017<br />
For BUREAU VERITAS,<br />
At BV GOTHENBURG, on 19 Oct 2012,<br />
Magne MOLLER<br />
This certificate remains valid until the date stated above, unless cancelled or revoked, provided the conditions indicated in the subsequent page(s) are complied<br />
with and the product remains satisfactory in service. This certificate will not be valid if the applicant makes any changes or modifications to the approved product,<br />
which have not been notified to, and agreed in writing with BUREAU VERITAS. Should the specified regulations or standards be amended during the validity of<br />
this certificate, the product(s) is/are to be re-approved prior to it/they being placed on board vessels to which the amended regulations or standards apply. This<br />
certificate is issued within the scope of the General Conditions of BUREAU VERITAS Marine Division available on the internet site www.veristar.com. Any<br />
Person not a party to the contract pursuant to which this document is delivered may not assert a claim against BUREAU VERITAS for any liability arising out of<br />
errors or omissions which may be contained in said document, or for errors of judgement, fault or negligence committed by personnel of the Society or of its<br />
Agents in establishment or issuance of this document, and in connection with any activities for which it may provide.<br />
BV Mod. Ad.E 530 May 2009<br />
This certificate consists of 4 page(s)
Page 2 / 4<br />
Certificate number: 07442/D0 BV<br />
THE SCHEDULE OF <strong>APPROVAL</strong><br />
1. PRODUCT DESCRIPTION<br />
Pump Series ACD, ACE, ACE Optiline, ACF, ACG, ACG Optiline,ACP, LPQ, D4 NTBP, LPD, LPE, LPE Optiline<br />
1.1 Pump Series Type ACD<br />
Size of rotor<br />
(mm)<br />
Maximum Discharge Pressure<br />
(bar)<br />
Flow rate<br />
(l/min)<br />
Motor speed<br />
(rpm)<br />
Service Temperature<br />
(°C)<br />
25 7 11-35 max 3600 -20/90<br />
1.2 Pump Series Type ACE<br />
Size of rotor<br />
(mm)<br />
Version Maximum Discharge Pressure<br />
(bar)<br />
Flow rate<br />
(l/min)<br />
Motor speed<br />
(rpm)<br />
Service Temperature<br />
(°C)<br />
25, 32, 38 NVxx 16 15-180 max 3600 -20/110<br />
NTxx 16 -20/155<br />
1.3 Pump series Type Optiline ACE<br />
Size of rotor<br />
(mm)<br />
Version * Maximum Discharge Pressure<br />
(bar)<br />
Flow rate<br />
(l/min)<br />
Motor speed<br />
(rpm)<br />
Service Temperature<br />
(°C)<br />
25, 32, 38 NKBP 16 10-180 max 3600 -20/155<br />
NLBP 16 -20/155<br />
NMBP 16 -20/155<br />
1.4 Pumps Series Type ACF<br />
Size of rotor<br />
(mm)<br />
Version Maximum Discharge Pressure<br />
(bar)<br />
Flow rate<br />
(l/min)<br />
Motor speed<br />
(rpm)<br />
Service Temperature<br />
(°C)<br />
80, 90, 100, 110, 125 IVxx 16 300-3000 max 1800 -20/90<br />
NVxx 16 -20/130<br />
1.5 Pump series Type ACG<br />
Size of rotor<br />
(mm)<br />
Version Maximum Discharge Pressure<br />
(bar)<br />
Flow rate<br />
(l/min)<br />
Motor speed<br />
(rpm)<br />
Service Temperature<br />
(°C)<br />
45, 52, 60, 70 NVxx 16 100-1100 max 3600 -20/90<br />
NTxx 16 -20/155<br />
1.6 Pump series Type ACG Optiline<br />
Size of rotor<br />
(mm)<br />
Version * Maximum Discharge Pressure<br />
(bar)<br />
Flow rate<br />
(l/min)<br />
Motor speed<br />
(rpm)<br />
Service Temperature<br />
(°C)<br />
45, 52, 60, 70 NHBP 16 80-1200 max 3600 -20/180<br />
NJBP 16<br />
NKBP 16<br />
NLBP 16<br />
NMBP 16<br />
* With a magnetic shaft coupling where<br />
Size of rotor<br />
(mm)<br />
Version Torque<br />
(Nm)<br />
Size of rotor<br />
(mm)<br />
Version Torque<br />
(Nm)<br />
Size of rotor<br />
(mm)<br />
Version Torque<br />
(Nm)<br />
25 K 6.5 H 10 K 22<br />
L 14 J 20 60 L 50<br />
K 6.5 45, 52 L 30 M 80<br />
32 L 14 M 40<br />
M 22 N 60 Size of rotor Version Torque<br />
L 14 (mm) (Nm)<br />
38 M 22 K 85<br />
N 30 70 L 135<br />
M 180<br />
1.7 Pump series Type ACP:<br />
ACD 025 with a fixed relief valve preset to 4 bar<br />
Size of rotor<br />
(mm)<br />
Maximum Discharge Pressure<br />
(bar)<br />
Flow rate<br />
(l/min)<br />
Motor speed<br />
(rpm)<br />
Service Temperature<br />
(°C)<br />
25 7 11-35 max 3600 -20/90<br />
ACE032, 038 with a fixed relief valve preset to 4 bar<br />
Size of rotor<br />
(mm)<br />
Version Maximum Discharge Pressure<br />
(bar)<br />
Flow rate<br />
(l/min)<br />
Motor speed<br />
(rpm)<br />
Service Temperature<br />
(°C)<br />
32, 38 NVxx 16 15-180 max 3600 -20/110<br />
NTxx 16 -20/155<br />
ACG045, 052, 060, 070 with a fixed relief valve preset to 4 bar<br />
Size of rotor<br />
(mm)<br />
Version Maximum Discharge Pressure<br />
(bar)<br />
Flow rate<br />
(l/min)<br />
Motor speed<br />
(rpm)<br />
Service Temperature<br />
(°C)<br />
45, 52, 60, 70 NVxx 16 100-1100 max 3600 -20/90<br />
NTxx 16 -20/155<br />
BV Mod. Ad.E 530 May 2009<br />
This certificate consists of 4 page(s)
Page 3 / 4<br />
Certificate number: 07442/D0 BV<br />
1.8 Pump series Type LPQ<br />
Size of rotor<br />
(mm)<br />
Version Maximum Discharge Pressure<br />
(bar)<br />
Flow rate<br />
(l/min)<br />
Motor speed<br />
(rpm)<br />
Service Temperature<br />
(°C)<br />
100, 110, 125, 140 IRYP 16 1300-7500 max 1800 -20/90<br />
ITYP 16 -20/90<br />
NRYP 16 -20/90<br />
NTYP 16 -20/90<br />
1.9 Pump series Type D4 NTBP<br />
Size of rotor<br />
(mm)<br />
Version Maximum Discharge Pressure<br />
(bar)<br />
Flow rate<br />
(l/min)<br />
Motor speed<br />
(rpm)<br />
Service Temperature<br />
(°C)<br />
25, 32, 38 NTBP 40 10-160 max 3600 -20/+180<br />
1.10 Pump series Type LPD<br />
Size of rotor<br />
(mm)<br />
Version Maximum Discharge Pressure<br />
(bar)<br />
Flow rate<br />
(l/min)<br />
Motor speed<br />
(rpm)<br />
15, 20 IVBP 10 2-20 max 3600 -20/90<br />
1.11 Pump series Type LPE<br />
Size of rotor<br />
Version Maximum Discharge Pressure Flow rate Motor speed<br />
(mm)<br />
(bar)<br />
(l/min) (rpm)<br />
25, 32, 38 NTBP 16 10-180 max 3600 -20/155<br />
NVBP 16 -20/155<br />
NTYP 16 -20/155<br />
NVYP 16 -20/155<br />
1.12 Pump series Type LPE Optiline<br />
Size of rotor<br />
(mm)<br />
Version * Maximum Discharge Pressure<br />
(bar)<br />
Flow rate<br />
(l/min)<br />
Motor speed<br />
(rpm)<br />
25, 32, 38 NKBP 16 80-175 max 3600 -20/180<br />
NLBP 16 -20/180<br />
NMBP 16 -20/180<br />
NNBP 16 -20/180<br />
NKYP 16 -20/180<br />
NLYP 16 -20/180<br />
NMYP 16 -20/180<br />
NNYP 16 -20/180<br />
Service Temperature<br />
(°C)<br />
Service Temperature<br />
(°C)<br />
Service Temperature<br />
(°C)<br />
* With a magnetic shaft coupling where<br />
Size of rotor<br />
(mm)<br />
Version Torque<br />
(Nm)<br />
25 K 6.5<br />
L 14<br />
K 6.5<br />
32 L 14<br />
M 22<br />
L 14<br />
38 M 22<br />
N 30<br />
1.13 Material specification depending on pump series<br />
Pump body Grey cast iron / Nodular cast iron<br />
Power rotor Surface-treated steel / Carbon steel<br />
Idler rotor Surface-treated grey cast iron / Surface-treated grey carbon steel / Carbon steel<br />
Shaft seal Carbon/ Ni-resist. elastomers in Viton/ nitrile or Carbon/ stainless steel, elastomers in Viton or Carbon/ Carbide, elastomers<br />
in Viton or Carbide/ Carbide, elastomers in Viton or Cast iron and Viton/nitrile elastomers<br />
2. DOCUMENTS AND DRAWINGS<br />
Type Dimensional Drawing Section Drawing Product Description<br />
ACD MS-22560 33463 C ACD6 1116.02 GB<br />
ACE MS-23809E 43867 G ACE3 1121.02 GB<br />
ACE Optiline 1 MS-25125 44064 OACE3 1101.01 GB<br />
ACF MS-22406J 43220D ACF4 1118.02GB<br />
ACF MS-24858 43985 ACF5 1101.01GB<br />
ACG MS-23892B / MS-24462A 43897 / 43898 / 43899 / 43919 / 43815A ACG7 1122.01 GB<br />
ACG Optiline MS-24881 43992 OACG8 1101.01 GB<br />
ACP MS-22560 / MS-23809E / MS-23892B / MS-24462A 33463 C / 43867 G /43897 / 43898 / 43899 / 43919 / 43815A -<br />
LPQ MS-23119B / MS-23124 43741D / 43760C LPQ 1103.02 GB<br />
D4 NTBP 2 MS-25368 44028 D4 1114.01GB<br />
LPD 3 MS24160C 34918A LPD_1102.01_GB<br />
LPE 4 MS-25341 / MS-25343 / MS-25354 / MS -25356 44018 LPE3 1101.01 GB<br />
LPE Optiline 5 MS-25342 / MS-25367 44022 LPE4 1101.01 GB<br />
BV Mod. Ad.E 530 May 2009<br />
This certificate consists of 4 page(s)
Page 4 / 4<br />
Certificate number: 07442/D0 BV<br />
- Parts list : 1/D-2114-0001B 2/D-2149-0001 3/ D1979-0001-A & D1984-0001-A 4/D-2151, 2153 5/ D-2150, 2152, 2154, 2155<br />
3. TEST REPORTS<br />
Not applicable.<br />
4. APPLICATION / LIMITATION<br />
4.1 Pumps may be used for the following operating fluids: lubricating oil, fuel oil, hydraulic oil and any non-aggressive fluid<br />
with sufficient lubricating properties.<br />
4.2 The pumps body and internal parts should be of a suitable type for use with fluids intended to be carried.<br />
4.3 The approval does not include the prime mover of the pump.<br />
4.4 The pump is to be installed according to manufacturer's instructions and Bureau Veritas Rules requirements.<br />
5. PRODUCTION SURVEY REQUIREMENTS<br />
5.1 The products are to be manufactured, examined and tested by the manufacturer in accordance with the approved type<br />
described in this certificate and Bureau Veritas Rules and Regulations stated on the front page of this certificate. Arrangements<br />
shall be made for a Society's Surveyor to attend the tests and examinations at manufacturer's works or to perform the relevant<br />
audits when an alternative survey scheme, BV Mode I, has been arranged, in order to issue the Bureau Veritas certificate for the<br />
approved type to be fitted on board ships classed with Bureau Veritas.<br />
5.2 The manufacturer has declared to Bureau Veritas that the products detailed in this certificate are manufactured at the<br />
production site stated on the front page of this certificate.<br />
5.3 Pump is to be hydrostatically and performance tested, and delivered with a Bureau Veritas certificate when required by the<br />
rules.<br />
6. MARKING OF PRODUCT<br />
Each pump is to be permanently marked with at least:<br />
- Manufacturer's name or logo<br />
- Product code<br />
- Serial number<br />
- Society's brand as relevant when required by the Rules<br />
7. OTHERS<br />
7.1 This certificate is given on the understanding that the manufacturer will accept full responsibility for informing shipbuilders<br />
or their sub-contractors of the proper methods of fitting and general maintenance of the product and of the conditions of this<br />
approval.<br />
7.2 This certificate supersedes the Type Approval Certificate N° 07442/C3 BV issued on 12/06/2012 by the Society.<br />
*** END OF <strong>CERTIFICATE</strong> ***<br />
BV Mod. Ad.E 530 May 2009<br />
This certificate consists of 4 page(s)
Change language