Flat Rate Labor Chart - Husqvarna Group

Flat Rate Labor Chart
1 UNIT = 6 minutes (1/10 hr.) R&R = Remove & Replace
CHAIN/CUT-OFF/CLEARING
SAWS, TRIMMERS, HEDGETRIMMERS & BLOWERS
TIME
TIME
SECTION UNITS JOB DESCRIPTION SECTION UNITS JOB DESCRIPTION
1 Replace tank cap; fuel/oil STARTER 5 Repair/replace springs, etc.
1 Replace chain brake assembly
(22HB, 28HBV, 26LRC,
1 Replace top cover
32R/LR/LRC)
1 Replace trimmer head as sembly
3 Repair/replace springs, etc.
1 Outer spike
2 Rope only
1 Replace assembly starter
6 Replace fuel line (334,335XPT,338)
CRANKCASE/ 25 Replace crankshaft (PS50 only) FUEL SYSTEM/ 2 Replace tank gasket (33, 35, 37, 38)
CRANKSHAFT 20 Split for gasket CARBURETOR 2 Replace fuel line/filter
20 Replace crankcase (324,224)
7 Replace carburetor(235,240,435,440,445,450)
Replace main bearing
2 Replace tank vent
Replace crankshaft (334,335XPT,338)
4 Replace carburetor shaft
15 Any of above procedures
3 Replace carburetor
(334, 335XPT, 336, 338, 339)
6 Rebuild carburetor and/or jet
(136, 137, 141, 142, 235, 240)
6
replacement
Replace tank
4 Replace seal
8 Replace tank (2100/298/2101)
2 Chain tensioner/inner spike
6 Rebuild carburetor (334,335XPT,338)
1 Bar bolt OILER 3 Replace oil line/filter
7 Replace oil line/filter (455, 460)
CYLINDER 7 Replace piston/components
2 Replace drive gear
15 Replace piston/cylinder
3 Replace oiler assembly
(40/45, 39R)
5 Repair oiler assembly
5 Replace cylinder
3 Repair oil assembly (40/45, 50, 2101)
10 Replace piston/cylinder
2 Replace oil tank vent
(22HB, 28HBV, 26LRC,
2 Replace oil tank gasket
32R/LR/LRC)
(33, 35, 37, 38)
15 Replace piston/cylinder (334, 335, 338)
15 Replace oiler (334, 335, 338)
CHAINBRAKE 6 Rebuild chain brake (33, 35, 37, 38) LEVERS 2 Replace choke/throttle wire
3 Rebuild chain brake (others )
6 Replace controls inner handle
2 Replace hand guard
(298, 2100, 2101)
4 Replace controls inner handle
CLUTCH/ 2 Replace rim/drum
(All others )
SPROCKET 2 Replace clutch
3 Replace throttle cable
2 Replace bearing
(40/45, 3120, 39R, 25R, 26LRC,
3 Replace clutch spring
39R/LR/LRC)
3 Replace controls inner handle (40/45)
HANDLES/ 2 Replace front handle
2 Replace controls inner handle
COVERS 5 Replace rear handle
(39R, 25R, 165RX)
HEATED/ 5 Replace generator AV MOUNTS 6 Replace any or all
HANDLES 3 Replace handle elements
3 Model 50, 40/45
2 7th/Spring (3120, 2100, 2101,
AIR FILTER/ 1 Replace air filter
298, 281)
MANIFOLD 2 Replace air filter elbow, brace
4 Replace intake manifold
2 Replace shaft(square end)
6 Replace intake manifold (334, 335, 338) CLEARING SAWS/ 6 Replace shaft(screw-in)/tube
TRIMMERS 2 Replace gear head
MUFFLER 2 Replace muffler
4 Fuel tank (39R, 244RX)
3 Repair studs
3 Fuel tank (all others)
6 Rebuild gear head
BLOWERS 6 Housing/impeller
4 Replace clutch
0 Tubes
4 Replace support tower for handles
4 AV mounts
IGNITION 2 Replace switch 1 Replace handle bracket (24R, 25R)
3 Replace wiring 1 Replace trimmer head components
4 Replace flywheel 1 Guard
5 Replace flywheel pawl, spring
5 Replace Hedgetrimmer blades / blade connecting rod
5 Replace: test & replace individual
components in 2 piece system CUTTING ARM
10
1
Replace Hedgetrimmer gearcase
Replace protective guard
4 Replace 1 piece component 2 Repair belt tensioner, or guard adjuster
(external) 5 Cutting arm, ball bearing, or pulley
5 Replace 1 piece component replacement
(internal, including 22HB, 28HBV,
26LRC, 32 R/LR/LRC) HELICOIL 2 Each +2.00