IN "RP & C - Associated Valve

Technical Data for:
RP&C / Bonney Forge Valves
Forged Steel Gate Valves
Forged Steel Globe Valves
Forged Steel Check Valves

RP&C FORGED STEEL CHECK VALVES
C90D NPT ENDS SIZES ¼” THRU 2”
C91D
SOCKET WELD ENDS
• ASTM A182 Gr. F5
• WORKING PRESSURE (NON-SHOCK)
600 PSIG @ 975° F. Steam-Oil
800 PSIG @ 930° F. Steam-Oil
2000 PSIG @ -20° To 100° F.
K90D NPT ENDS SIZES ¼” THRU 2”
K91D SOCKET WELD ENDS
• ASTM A182 Gr. F22 Cl. 3
• WORKING PRESSURE (NON-SHOCK)
600 PSIG @ 1615° F. Steam-Oil
800 PSIG @ 1355° F. Steam-Oil
2000 PSIG @ -20° To 100° F
HORIZONTAL SERVICE ONLY
• PISTON CHECK VALVE
• STANDARD PORT
• BOLTED COVER
• CONFORM TO THE APPLICABLE PARTS OF
THEFOLLOWING SPECIFICATIONS:
API
API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
D TRIM (13 Cr/HF) STANDARD (See Page 8 for optional trims)
No. Part Material
1 Nameplate Aluminum
ASTM
Spec.
Remarks
2 Cover Forged Steel A182 Grade F5
2 Cover Forged Steel A182 Grade F22 Cl. 3
3 Cover Bolts Alloy Steel A193 Grade B16
4 * Gasket 316 SS/Grafoil® Spiral Wound
5 Disc 420 Stainless Steel A582 Heat Treated
6 Body Forged Steel A182 Grade F5
6 Body Forged Steel A182 Grade F22 Cl. 3
7 Seat Cobalt-Chromium Super Alloy CoCr-A
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
FLOW
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size End To End
Center to
Socket Weld Socket Weld Approximate Typical Cv
Port Dia.
Top(Open)
Bore
Depth
Weight Factors
1/4 3 2-3/16 9/32 .555 .375 3-1/4 .8
3/8 3 2-3/16 5/16 .690 .375 3-1/4 .9
1/2 3 2-3/16 3/8 .855 .375 3-1/4 1.0
3/4 3-1/2 2-7/16 ½ 1.065 .500 3-3/4 2.7
1 4-3/8 2-13/16 ¾ 1.330 .500 5-1/2 6.4
1-1/4 6 3-11/16 1 1.675 .500 11 14.0
1-1/2 6 3-11/16 1-1/4 1.915 .500 11 18.0
2 7 4-5/16 1-1/2 2.406 .625 14-1/2 24.0
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 2C

RP&C FORGED STEEL CHECK VALVES
F1300E SIZES 1/4” THRU 1-1/2”
F1310E SIZES 1/4” THRU 2”
F1320E SIZES 1/4” THRU 2”
NPT
SOCKET WELD
BUTT WELD
• SPRING LOADED PISTON CHECK VALVES
• HORIZONTAL OR VERTICAL SERVICE
• FORGED STEEL ASTM A105
• SEAL WELDED COVER
• REFER TO CHART ON PAGE 2Y FOR PRESSURE/TEMP. RATINGS
(NOT RECOMMENDED FOR PROLONGED USE ABOVE 800 F°)
• CONFORMS TO THE APPLICABLE PARTS OF THE
FOLLOWING ASME/ANSI SPECIFICATIONS:
B16.34
B31.3
B1.20.1 SCREWED ENDS
B16.11 SOCKET WELD ENDS
B16.25 BUTT WELD ENDS
MATERIALS OF CONSTRUCTION
NO. PART MATERIAL
ASTM
SPEC.
1 Body Forged Steel A105
REMARKS
2 Seat Ring Cobalt-Chromium Super Alloy CoCr-A
3 Cover Forged Steel A105
4 Disc Cobalt-Chromium Super Alloy CoCr-A
5 Spring Stainless Steel Type 302
6 Nameplate Aluminum
FLOW
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size End To End
Center to
Socket Weld Socket Weld Approximate Typical Cv
Port
Top(Open)
Bore
Depth
Weight Factors
1/4 4-1/2 3-1/8 5-16 .555 .375 3-3/4 2.0
3/8 4-1/2 3-1/8 3/8 .690 .375 3-3/4 2.5
1/2 4-1/2 3-1/8 7/16 .855 .375 3-3/4 3.5
3/4 4-1/2 3-1/8 9/16 1.065 .500 3-3/4 5.6
1 5-7/16 3-3/4 13/16 1.330 .500 6-1/2 12.7
1-1/4 8-1/4 5-5/16 1-1/8 1.675 .500 15-1/2 26.0
1-1/2 8-1/4 5-5/16 1-1/4 1.915 .500 15-1/2 35.0
2 9-1/2 6-5/16 1-9/16 2.406 .625 24 46.0
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 11Y

RP&C FORGED STEEL CHECK VALVES
F1350E SIZES 1/4” THRU 1-1/2” NPT (CLASS 2500)*
F1360E SIZES 1/4” THRU 2”
F1370E SIZES 1/4” THRU 2”
SOCKET WELD
BUTT WELD
• SPRING LOADED PISTON CHECK VALVES
• HORIZONTAL OR VERTICAL SERVICE
• FORGED STEEL ASTM A105
• SEAL WELDED COVER
• REFER TO CHART ON PAGE 2Y FOR PRESSURE/TEMP. RATINGS
(NOT RECOMMENDED FOR PROLONGED USE ABOVE 800 F°)
• CONFORMS TO THE APPLICABLE PARTS OF THE
FOLLOWING ASME/ANSI SPECIFICATIONS:
B16.34
B31.3
B1.20.1 SCREWED ENDS
B16.11 SOCKET WELD ENDS
B16.25 BUTT WELD ENDS
MATERIALS OF CONSTRUCTION
NO. PART MATERIAL
ASTM
SPEC.
1 Body Forged Steel A105
REMARKS
2 Seat Ring Cobalt-Chromium Super Alloy CoCr-A
3 Cover Forged Steel A105
4 Disc Cobalt-Chromium Super Alloy CoCr-A
5 Spring Stainless Steel Type 302
6 Nameplate Aluminum
FLOW
ASME B16.34 DOES NOT ALLOW FOR THREADED ENDS
ABOVE CLASS 2500
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size End To End
Center to
Socket Weld Socket Weld Approximate Typical Cv
Port
Top(Open)
Bore
Depth
Weight Factors
1/4 4-1/2 3-1/8 5-16 .555 .375 3-3/4 2.0
3/8 4-1/2 3-1/8 3/8 .690 .375 3-3/4 2.5
1/2 4-1/2 3-1/8 7/16 .855 .375 3-3/4 3.5
3/4 4-1/2 3-1/8 9/16 1.065 .500 3-3/4 5.6
1 5-7/16 3-3/4 13/16 1.330 .500 6-1/2 12.7
1-1/4 8-1/4 5-5/16 1-1/8 1.675 .500 15-1/2 26.0
1-1/2 8-1/4 5-5/16 1-1/4 1.915 .500 15-1/2 35.0
2 9-1/2 6-5/16 1-9/16 2.406 .625 24 46.0
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 13Y

RP&C FORGED STEEL CHECK VALVES
F190D
F390D
F690D
CLASS 150 FLANGED
CLASS 300 FLANGED
CLASS 600 FLANGED
• SIZES 1/2” THRU 2”
FOR HORIZONTAL SERVICE ONLY
• FORGED STEEL
• ASTM A105N, LOW CARBON (.25 MAX.), NORMALIZED
• STANDARD PORT
• BOLTED COVER
• WORKING PRESSURE (NON-SHOCK)
CLASS 150
150 PSIG @ 576° F. Steam-Oil
285 PSIG @ -20° To 100° F.
CLASS 300
300 PSIG @ 839° F. Steam-Oil
740 PSIG @ -20° To 100° F.
CLASS 600
600 PSIG @ 576° F. Steam-Oil
1480 PSIG @ -20° To 100° F.
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
No. Part Material
1 Nameplate Aluminum
ASTM
Spec.
Remarks
2 Cover Forged Steel, Normalized A105N Low Carbon
3 Cover Bolts Alloy Steel A193 Grade B7
4 * Gasket 316 SS/Grafoil® Spiral Wound
5 Disc 420 Stainless Steel A582 Heat Treated
6 Body Forged Steel, Normalized A105N Low Carbon
7 Seat Cobalt-Chromium Super Alloy CoCr-A
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and
Production runs, however parts will still conform to the requirements of API
602.
FLOW
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size
Face To Face
Center to Port
Approximate Weight
Typical Cv
150 300 600
Top(Open) Dia.
150 300 600
Factors
½ 4-1/4 6 6-1/2 6-3/8 3/8 6 7-1/4 7-3/4 1.0
¾ 4-5/8 7 7-1/2 6-5/8 ½ 6-3/4 9-3/4 10-3/4 2.7
1 5 8 8-1/2 8-1/4 ¾ 10 11 12 6.4
1 ½ 6-1/2 9 9-1/2 9-1/4 1-1/4 17 22 25 18.0
2 8 10-1/2 11-1/2 11 1-1/2 26 32 34 24.0
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 7C

F191D
F391D
F691D
RP&C FORGED STEEL CHECK VALVES
CLASS 150 FLANGED
CLASS 300 FLANGED
CLASS 600 FLANGED
SIZES ¼” THRU 2”
FOR HORIZONTAL SERVICE ONLY
• FORGED STEEL
• ASTM A105, LOW CARBON (.25 MAX.), NORMALIZED
• STANDARD PORT
• OS&Y – STOP/CHECK VALVE
CLASS 150
150 PSIG @ 576° F. Steam-Oil
285 PSIG @ -20° To 100° F.
CLASS 300
300 PSIG @ 839° F. Steam-Oil
740 PSIG @ -20° To 100° F.
CLASS 600
600 PSIG @ 576° F. Steam-Oil
1480 PSIG @ -20° To 100° F.
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
• MATERIALS OF CONSTRUCTION
No. Part Material
ASTM
Spec.
Remarks
1 Handwheel Malleable Iron A47 Gr. 32510
2 Handwheel Nut Steel A108
3 Nameplate Aluminum
4 Operating Nut Stainless Steel A276 Type 410
5 Stem Stainless Steel A276 Type 410
6 Gland Nuts 303 Stainless Steel A194 Grade 8F
7 Gland Flange Carbon Steel A108 Grade 1018
8 Gland Carbon Steel B484 Gr. 1, Cl. C, Type 1
9 Eyebolt 410 Stainless Steel Hardened & Tempered
10 Eyebolt Washer Carbon Steel Grade 1018
11a * Packing Graphite Grafoil® (241 or equal)
11b * Wiper Rings Braided Graphite 1630GF or equal
12 Bonnet Bolts Alloy Steel A193 Grade B7
13 Bonnet Forged Steel, Normalized A105N Low Carbon
14 * Gasket 316 SS/Grafoil® Spiral Wound
15 Seat Cobalt-Chromium Super Alloy CoCr-A
16 Disc 420 Stainless Steel A582 Heat Treated
17 Body Forged Steel, Normalized A105N Low Carbon
Operating Nut and Stem thread Lubricated
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
FLOW
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size
Handwheel Face To Face Center to Port
Approximate Weight
Typical Cv
Dia.
150 300 600
Top(Open) Dia.
150 300 600
Factors
½ 3-7/8 4-1/4 6 6-1/2 6-3/8 3/8 6-3/4 7 8 1.0
¾ 3-7/8 4-5/8 7 7-1/2 6-5/8 ½ 7-1/2 10 11 2.7
1 5-1/2 5 8 8-1/2 8-1/4 ¾ 11 14 15 6.4
1 ½ 5-1/2 6-1/2 9 9-1/2 9-1/4 1-1/4 19 24-1/2 26 18.0
2 6-1/2 8 10-1/2 11-1/2 11 1-1/2 30 38 40 24.0
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 8C

RP&C VALVES – CLASS 1500
F594E NPT ENDS
F595E
SOCKET WELD ENDS
SIZES 1/2” THRU 2”
• PISTON CHECK VALVE
• ASTM A105N LOW CARBON (.25 MAX.), NORMALIZED
• STANDARD PORT
• OS&Y – BOLTED BONNET
• WORKING PRESSURE (NON-SHOCK)
860 PSIG @ 900° F. Steam-Oil
1340 PSIG @ 850° F. Steam-Oil
3705 PSIG @ -20° To 100° F.
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 591 API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
E TRIM (13 Cr/FHF) STANDARD (See Page 8 for optional trims)
No. Part Material
1 Nameplate Aluminum
ASTM
Spec.
Remarks
2 Cap Forged Steel, Normalized A015N Low Carbon
3 Cap Bolts Alloy Steel A193 Grade B7
4 * Gasket 316 SS/Grafoil® Spiral Wound
5 Disc Cobalt-Chromium Super Alloy CoCr-A
6 Body Forged Steel, Normalized A105N Low Carbon
7 Seat Cobalt-Chromium Super Alloy CoCr-A
8 Spring Stainless Steel Type 302
Operating Nut and Stem thread Lubricated
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size End To End
Center to
Socket Weld Socket Weld Approximate Typical Cv
Port
Top(Open)
Bore
Depth
Weight Factors
1/2 4 2-7/8 25/64 .855 .375 5-1/2 1.3
3/4 4 2-7/8 1/2 1.065 .500 6-1/4 1.8
1 5-1/2 3-5/16 3/4 1.330 .500 10 7.0
1-1/2 6-1/2 4-7/16 1-3/16 1.915 .500 18-1/2 18.1
2 7 6-1/4 1-15/32 2.406 .625 29-3/4 23
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 7 V15

RP&C FORGED STEEL CHECK VALVES
F90D NPT ENDS SIZES ¼” THRU 2”
F91D
SOCKET WELD ENDS
• FORGED STEEL
• ASTM A105, LOW CARBON (.25 MAX.), NORMALIZED
• WORKING PRESSURE (NON-SHOCK)
460 PSIG @ 900° F. Steam-Oil
715 PSIG @ 850° F. Steam-Oil
1975 PSIG @ -20° To 100° F.
LF90D NPT ENDS SIZES ¼” THRU 2”
LF91D
SOCKET WELD ENDS
• ASTM A350 Gr. LF2 (for low temperature service)
• WORKING PRESSURE (NON-SHOCK)
1100 PSIG @ 800° F. Steam-Oil
1975 PSIG @ -50° To 100° F.
800° F. IS MAX OPERATING TEMP. FOR LF2
HORIZONTAL SERVICE ONLY
• PISTON CHECK VALVE
• STANDARD PORT
• BOLTED COVER
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
D TRIM (13 Cr/HF) STANDARD (See Page 8 for optional trims)
No. Part Material
1 Nameplate Aluminum
ASTM
Spec.
Remarks
2 Cover Forged Steel, Normalized A105N Low Carbon
2 Cover Forged Steel A350 Grade LF2
3 Cover Bolts Alloy Steel A193 Grade B7/ Grade B8M Cl.2
4 * Gasket 316 SS/Grafoil® Spiral Wound
5 Disc 420 Stainless Steel A582 Heat Treated
6 Body Forged Steel, Normalized A105N Low Carbon
6 Body Forged Steel A350 Grade LF2
7 Seat Cobalt-Chromium Super Alloy CoCr-A
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
FLOW
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size End To End
Center to
Socket Weld Socket Weld Approximate Typical Cv
Port Dia.
Top(Open)
Bore
Depth
Weight Factors
1/4 3 2-3/16 9/32 .555 .375 3-1/4 .8
3/8 3 2-3/16 5/16 .690 .375 3-1/4 .9
1/2 3 2-3/16 3/8 .855 .375 3-1/4 1.0
3/4 3-1/2 2-7/16 ½ 1.065 .500 3-3/4 2.7
1 4-3/8 2-13/16 ¾ 1.330 .500 5-1/2 6.4
1-1/4 6 3-11/16 1 1.675 .500 11 14.0
1-1/2 6 3-11/16 1-1/4 1.915 .500 11 18.0
2 7 4-5/16 1-1/2 2.406 .625 14-1/2 24.0
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 1C

RP&C FORGED STEEL CHECK VALVES
F92D NPT ENDS SIZES ¼” THRU 2”
F93D SOCKET WELD ENDS
HORIZONTAL SERVICE ONLY
• ASTM A105, LOW CARBON (.25 MAX.), NORMALIZED
• WORKING PRESSURE (NON-SHOCK)
460 PSIG @ 900° F. Steam-Oil
715 PSIG @ 850° F. Steam-Oil
1975 PSIG @ -20° To 100° F.
• STOP/CHECK VALVE
• STANDARD PORT
• OS&Y – BOLTED BONNET
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
D TRIM (13 Cr/HF) STANDARD (See Page 8 for optional trims)
No. Part Material
ASTM
Spec.
Remarks
1 Handwheel Malleable Iron A47 Gr. 32510
2 Handwheel Nut Steel A108
3 Nameplate Aluminum
4 Operating Nut Stainless Steel A276 Type 410
5 Stem Stainless Steel A276 Type 410
6 Gland Nuts 303 Stainless Steel A194 Grade 8F
7 Gland Flange Carbon Steel A108 Grade 1018
8 Gland Carbon Steel B484 Gr. 1, Cl. C, Type 1
9 Eyebolt 410 Stainless Steel Hardened & Tempered
10 Eyebolt Washer Carbon Steel Grade 1018
11a * Packing Graphite Grafoil® (241 or equal)
11b * Wiper Rings Braided Graphite 1630GF or equal
12 Bonnet Bolts Alloy Steel A193 Grade B7
13 Bonnet Forged Steel, Normalized A105N Low Carbon
14 * Gasket 316 SS/Grafoil® Spiral Wound
15 Seat Cobalt-Chromium Super Alloy CoCr-A
16 Disc 420 Stainless Steel A582 Heat Treated
17 Body Forged Steel, Normalized A105N Low Carbon
Operating Nut and Stem thread Lubricated
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
FLOW
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size
Handwheel End To Center to Port Socket Weld Socket Weld Approximate Typical Cv
Dia. End Top(Open) Dia. Bore
Depth
Weight Factors
1/4 3-7/8 3 6-3/8 9/32 .555 .375 4 1.1
3/8 3-7/8 3 6-3/8 5/16 .690 .375 4 1.6
1/2 3-7/8 3 6-3/8 3/8 .855 .375 4 2.1
3/4 3-7/8 3-1/2 6-5/8 ½ 1.065 .500 4-1/2 3.1
1 5-1/2 4-3/8 8-1/4 ¾ 1.330 .500 7 7.0
1-1/4 5-1/2 6 9-1/4 1 1.675 .500 14 15.4
1-1/2 5-1/2 6 9-1/4 1-1/4 1.915 .500 13-1/2 18.1
2 6-1/2 7 11 1-1/2 2.406 .625 19 25.2
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 4C

RP&C FORGED STEEL CHECK VALVES
F94D NPT ENDS SIZES ¼” THRU 2”
F95D
SOCKET WELD ENDS
• FORGED STEEL
• ASTM A105, LOW CARBON (.25 MAX.), NORMALIZED
• WORKING PRESSURE (NON-SHOCK)
460 PSIG @ 900° F. Steam-Oil
715 PSIG @ 850° F. Steam-Oil
1975 PSIG @ -20° To 100° F.
HORIZONTAL SERVICE ONLY
• SPRING LOADED PISTON CHECK VALVE
• STANDARD PORT
• BOLTED COVER
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
D TRIM (13 Cr/HF) STANDARD (See Page 8 for optional trims)
No. Part Material
1 Nameplate Aluminum
ASTM
Spec.
Remarks
2 Cover Forged Steel, Normalized A105N Low Carbon
3 Cover Bolts Alloy Steel A193 Grade B7
4 * Gasket 316 SS/Grafoil® Spiral Wound
5 Disc 420 Stainless Steel A582 Heat Treated
6 Body Forged Steel, Normalized A105N Low Carbon
7 Seat Cobalt-Chromium Super Alloy CoCr-A
8 Spring Stainless Steel Type 302
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
FLOW
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size End To End
Center to
Socket Weld Socket Weld Approximate Typical Cv
Port Dia.
Top(Open)
Bore
Depth
Weight Factors
1/4 3 2-3/16 9/32 .555 .375 3-1/4 .8
3/8 3 2-3/16 5/16 .690 .375 3-1/4 .9
1/2 3 2-3/16 3/8 .855 .375 3-1/4 1.0
3/4 3-1/2 2-7/16 ½ 1.065 .500 3-3/4 2.7
1 4-3/8 2-13/16 ¾ 1.330 .500 5-1/2 6.4
1-1/4 6 3-11/16 1 1.675 .500 11 14.0
1-1/2 6 3-11/16 1-1/4 1.915 .500 11 18.0
2 7 4-5/16 1-1/2 2.406 .625 14-1/2 24.0
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 5C

RP&C FORGED STEEL CHECK VALVES
F96D NPT ENDS SIZES ¼” THRU 2”
F97D SOCKET WELD ENDS
• FORGED STEEL
• ASTM A105, LOW CARBON (.25 MAX.), NORMALIZED
• WORKING PRESSURE (NON-SHOCK)
460 PSIG @ 900° F. Steam-Oil
715 PSIG @ 850° F. Steam-Oil
1975 PSIG @ -20° To 100° F.
VERTICAL AND HORIZONTAL SERVICE
• SPRING LOADED BALL CHECK VALVE
• STANDARD PORT
• BOLTED COVER
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
D TRIM (13Cr/HF) STANDARD (See Page 8 for optional trims)
No. Part Material
1 Nameplate Aluminum
ASTM
Spec.
Remarks
2 Cover Forged Steel, Normalized A105N Low Carbon
3 Cover Bolts Alloy Steel A193 Grade B7
4 * Gasket 316 SS/Grafoil® Spiral Wound
5 Ball Alloy Steel A276 Grade 440
6 Body Forged Steel, Normalized A105N Low Carbon
7 Seat Cobalt-Chromium Super Alloy CoCr-A
8 Spring Stainless Steel Type 302
9 Ball Guide 416 Stainless Steel A582 Type 416
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size End To End
Center to
Socket Weld Socket Weld Approximate Typical Cv
Port Dia.
Top(Open)
Bore
Depth
Weight Factors
1/4 3 2-3/16 9/32 .555 .375 3-1/4 .8
3/8 3 2-3/16 5/16 .690 .375 3-1/4 .9
1/2 3 2-3/16 3/8 .855 .375 3-1/4 1.0
3/4 3-1/2 2-7/16 ½ 1.065 .500 3-3/4 2.7
1 4-3/8 2-13/16 ¾ 1.330 .500 5-1/2 6.4
1-1/4 6 3-11/16 1 1.675 .500 11 14.0
1-1/2 6 3-11/16 1-1/4 1.915 .500 11 18.0
2 7 4-5/16 1-1/2 2.406 .625 14-1/2 24.0
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 6C

RP&C FORGED STEEL CHECK VALVES
F98A NPT ENDS SIZES ¼” THRU 2”
F99A
SOCKET WELD ENDS
• SWING CHECK VALVE
• ASTM A105, LOW CARBON (.25 MAX.), NORMALIZED
• WORKING PRESSURE (NON-SHOCK)
460 PSIG @ 900° F. Steam-Oil
715 PSIG @ 850° F. Steam-Oil
1975 PSIG @ -20° To 100° F.
HORIZONTAL SERVICE ONLY
• STANDARD PORT
• BOLTED COVER
• EXCELLENT Cv VALUES
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
A TRIM (316 SST) STANDARD (See Page 8 for optional trims)
No. Part Material
1 Nameplate Aluminum
ASTM
Spec.
Remarks
2 Cover Forged Steel, Normalized A105N Low Carbon
3 Cover Bolts Alloy Steel A193 Grade B7M
4 * Gasket 316 SS/Grafoil® Spiral Wound
5 Disc 316 Stainless Steel A276 Type 316
6 Disc Nut 303 Stainless Steel Grade 8F
7 Seat Ring 316 Stainless Steel A351 Type CF8M
8 Hinge Pin 316 Stainless Steel
9 Swing Arm 316 Stainless Steel A351 Type CF8M
10 Body Forged Steel, Normalized A105N Low Carbon
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size End To End
Center to
Socket Weld Socket Weld Approximate Typical Cv
Port Dia.
Top(Open)
Bore
Depth
Weight Factors
1/2 3 2-3/16 25/64 .855 .375 3-1/4 5.1
3/4 3-1/2 2-7/16 ½ 1.065 .500 3-3/4 9.3
1 4-3/8 2-13/16 ¾ 1.330 .500 5-1/2 24.8
1-1/2 6 3-11/16 1-3/16 1.915 .500 11 70.9
2 7 4-5/16 1-15/32 2.406 .625 14-1/2 91.6
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 9C

RP&C VALVES – CLASS 1500
FWB594E NPT ENDS
FWB595E
SIZES 1/2” THRU 2”
SOCKET WELD ENDS
• PISTON CHECK VALVE
• ASTM A105N LOW CARBON (.25 MAX.), NORMALIZED
• STANDARD PORT
• OS&Y – WELDED BONNET
• WORKING PRESSURE (NON-SHOCK)
860 PSIG @ 900° F. Steam-Oil
1340 PSIG @ 850° F. Steam-Oil
3705 PSIG @ -20° To 100° F.
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 591 API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
E TRIM (13 Cr/FHF) STANDARD (See Page 8 for optional trims)
No. Part Material
1 Nameplate Aluminum
ASTM
Spec.
Remarks
2 Cap Forged Steel, Normalized A015N Low Carbon
3 Disc Cobalt-Chromium Super Alloy CoCr-A
4 Body Forged Steel, Normalized A105N Low Carbon
5 Seat Cobalt-Chromium Super Alloy CoCr-A
6 Spring Stainless Steel Type 302
Operating Nut and Stem thread Lubricated
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size End To End
Center to
Socket Weld Socket Weld Approximate Typical Cv
Port
Top(Open)
Bore
Depth
Weight Factors
1/2 4 2-7/8 25/64 .855 .375 5-1/2 1.3
3/4 4 2-7/8 1/2 1.065 .500 6-1/4 1.8
1 5-1/2 3-5/16 3/4 1.330 .500 10 7.0
1-1/2 6-1/2 4-7/16 1-3/16 1.915 .500 18-1/2 18.1
2 7 6-1/4 1-15/32 2.406 .625 29-3/4 23.0
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 8 V15

RP&C FORGED STEEL CHECK VALVES
K1300E SIZES 1/4” THRU 1-1/2” NPT
K1310E SIZES 1/4” THRU 2” SOCKET WELD
K1320E SIZES 1/4” THRU 2” BUTT WELD
• SPRING LOADED PISTON CHECK VALVES
• HORIZONTAL OR VERTICAL SERVICE
• FORGED STEEL ASTM A182 GRADE F22 Cl. 3
(2-1/4% Chrome 1% Moly)
• SEAL WELDED COVER
• REFER TO CHART ON PAGE 2Y FOR PRESSURE/TEMP. RATINGS
(NOT RECOMMENDED FOR PROLONGED USE ABOVE 1100 F°)
• CONFORMS TO THE APPLICABLE PARTS OF THE
FOLLOWING ASME/ANSI SPECIFICATIONS:
B16.34
B31.3
B1.20.1 SCREWED ENDS
B16.11 SOCKET WELD ENDS
B16.25 BUTT WELD ENDS
MATERIALS OF CONSTRUCTION
NO. PART MATERIAL
ASTM
SPEC.
REMARKS
1 Body Forged Steel A182 Grade F22 Cl. 3
2 Seat Ring Cobalt-Chromium Super Alloy CoCr-A
3 Cover Forged Steel A182 Grade F22 Cl. 3
4 Disc Cobalt-Chromium Super Alloy CoCr-A
5 Spring Stainless Steel Type 302
6 Nameplate Aluminum
FLOW
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size End To End
Center to
Socket Weld Socket Weld Approximate Typical Cv
Port
Top(Open)
Bore
Depth
Weight Factors
1/4 4-1/2 3-1/8 5-16 .555 .375 3-3/4 2.0
3/8 4-1/2 3-1/8 3/8 .690 .375 3-3/4 2.5
1/2 4-1/2 3-1/8 7/16 .855 .375 3-3/4 3.5
3/4 4-1/2 3-1/8 9/16 1.065 .500 3-3/4 5.6
1 5-7/16 3-3/4 13/16 1.330 .500 6-1/2 12.7
1-1/4 8-1/4 5-5/16 1-1/8 1.675 .500 15-1/2 26.0
1-1/2 8-1/4 5-5/16 1-1/4 1.915 .500 15-1/2 35.0
2 9-1/2 6-5/16 1-9/16 2.406 .625 24 46.0
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 12Y

RP&C FORGED STEEL CHECK VALVES
K1350E SIZES 1/4” THRU 1-1/2” NPT (CLASS 2500)*
K1360E SIZES 1/4” THRU 2” SOCKET WELD
K1370E SIZES 1/4” THRU 2” BUTT WELD
• SPRING LOADED PISTON CHECK VALVES
• HORIZONTAL OR VERTICAL SERVICE
• FORGED STEEL ASTM A182 GRADE F22 Cl. 3
(2-1/4% Chrome 1% Moly)
• SEAL WELDED COVER
• REFER TO CHART ON PAGE 2Y FOR PRESSURE/TEMP. RATINGS
(NOT RECOMMENDED FOR PROLONGED USE ABOVE 1100 F°)
• CONFORMS TO THE APPLICABLE PARTS OF THE
FOLLOWING ASME/ANSI SPECIFICATIONS:
B16.34
B31.3
B1.20.1 SCREWED ENDS
B16.11 SOCKET WELD ENDS
B16.25 BUTT WELD ENDS
MATERIALS OF CONSTRUCTION
NO. PART MATERIAL
ASTM
SPEC.
REMARKS
1 Body Forged Steel A182 Grade F22 Cl. 3
2 Seat Ring Cobalt-Chromium Super Alloy CoCr-A
3 Cover Forged Steel A182 Grade F22 Cl. 3
4 Disc Cobalt-Chromium Super Alloy CoCr-A
5 Spring Stainless Steel Type 302
6 Nameplate Aluminum
FLOW
ASME B16.34 DOES NOT ALLOW FOR THREADED ENDS
ABOVE CLASS 2500
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size End To End
Center to
Socket Weld Socket Weld Approximate Typical Cv
Port
Top(Open)
Bore
Depth
Weight Factors
1/4 4-1/2 3-1/8 5-16 .555 .375 3-3/4 2.0
3/8 4-1/2 3-1/8 3/8 .690 .375 3-3/4 2.5
1/2 4-1/2 3-1/8 7/16 .855 .375 3-3/4 3.5
3/4 4-1/2 3-1/8 9/16 1.065 .500 3-3/4 5.6
1 5-7/16 3-3/4 13/16 1.330 .500 6-1/2 12.7
1-1/4 8-1/4 5-5/16 1-1/8 1.675 .500 15-1/2 26.0
1-1/2 8-1/4 5-5/16 1-1/4 1.915 .500 15-1/2 35.0
2 9-1/2 6-5/16 1-9/16 2.406 .625 24 46.0
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 14Y

RP&C FORGED STEEL CHECK VALVES
S90A NPT ENDS SIZES ¼” THRU 2”
S91A SOCKET WELD ENDS
• FORGED STAINLESS STEEL
• WORKING PRESSURE (NON-SHOCK)
600 PSIG @ 1200° F. Steam-Oil
800 PSIG @ 1130° F. Steam-Oil
1920 PSIG @ -20° To 100° F
HORIZONTAL SERVICE ONLY
• ASTM A182 TYPE F316/F316L
• STANDARD PORT
• BOLTED COVER
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
A TRIM (316 SST) STANDARD (See Page 8 for optional trims)
No. Part Material
1 Nameplate Aluminum
ASTM
Spec.
Remarks
2 Cover Forged Stainless Steel A182 Type F316/F316L
3 Cover Bolts Alloy Steel A193 Grade B8M Cl. 2
4 * Gasket 316 SS/Grafoil® Spiral Wound
5 Disc 316 Stainless Steel A176 Grade 316
6 Body Forged Stainless Steel A182 Type F316/F316L
7 Seat 316 Stainless Steel Integral
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
FLOW
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size End To End
Center to
Socket Weld Socket Weld Approximate Typical Cv
Port Dia.
Top(Open)
Bore
Depth
Weight Factors
1/4 3 2-3/16 9/32 .555 .375 3-1/4 .8
3/8 3 2-3/16 5/16 .690 .375 3-1/4 .9
1/2 3 2-3/16 3/8 .855 .375 3-1/4 1.0
3/4 3-1/2 2-7/16 ½ 1.065 .500 3-3/4 2.7
1 4-3/8 2-13/16 ¾ 1.330 .500 5-1/2 6.4
1-1/4 6 3-11/16 1 1.675 .500 11 14.0
1-1/2 6 3-11/16 1-1/4 1.915 .500 11 18.0
2 7 4-5/16 1-1/2 2.406 .625 14-1/2 24.0
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 3C

RP&C FORGED STEEL CHECK VALVES
S98A NPT ENDS SIZES ¼” THRU 2”
S99A SOCKET WELD ENDS
HORIZONTAL SERVICE ONLY
• STAINLESS STEEL, ASTM A182 Gr. F316/F316L
• WORKING PRESSURE (NON-SHOCK)
600 PSIG @ 1200° F. Steam-Oil
800 PSIG @ 1130° F. Steam-Oil
1920 PSIG @ -20° To 100° F.
• STOP/CHECK VALVE
• STANDARD PORT
• OS&Y – BOLTED BONNET
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
A TRIM (316 SST) STANDARD (See Page 8 for optional trims)
No. Part Material
1 Nameplate Aluminum
ASTM
Spec.
Remarks
2 Cover 316 Stainless Steel A182 Gr. F316/F316L
3 Cover Bolts Alloy Steel A193 Grade B8M Cl. 2
4 * Gasket 316 SS/Grafoil® Spiral Wound
5 Disc 316 Stainless Steel A276 Type 316
6 Disc Nut 303 Stainless Steel Grade 8F
7 Seat Ring 316 Stainless Steel A351 Type CF8M
8 Hinge Pin 316 Stainless Steel
9 Swing Arm 316 Stainless Steel A351 Type CF8M
10 Body 316 Stainless Steel A182 Gr. F316/F316L
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size End To End
Center to
Socket Weld Socket Weld Approximate Typical Cv
Port Dia.
Top(Open)
Bore
Depth
Weight Factors
1/2 3 2-3/16 25/64 .855 .375 3-1/4 5.1
3/4 3-1/2 2-7/16 ½ 1.065 .500 3-3/4 9.3
1 4-3/8 2-13/16 ¾ 1.330 .500 5-1/2 24.8
1-1/2 6 3-11/16 1-3/16 1.915 .500 11 70.9
2 7 4-5/16 1-15/32 2.406 .625 14-1/2 91.6
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 10C

RP&C FORGED STEEL GLOBE VALVES
C80D NPT ENDS SIZES ¼” THRU 2”
C81D
SOCKET WELD ENDS
• ASTM A182 Gr. F5
• WORKING PRESSURE (NON-SHOCK)
600 PSIG @ 1615° F. Steam-Oil
800 PSIG @ 1355° F. Steam-Oil
2000 PSIG @ -20° To 100° F.
K80D NPT ENDS SIZES ¼” THRU 2”
K81D
SOCKET WELD ENDS
• ASTM A182 Gr. F22 Cl. 3
• WORKING PRESSURE (NON-SHOCK)
600 PSIG @ 1615° F. Steam-Oil
800 PSIG @ 1355° F. Steam-Oil
2000 PSIG @ -20° To 100° F.
• STANDARD PORT
• OS&Y – BOLTED BONNET
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
D TRIM (13 Cr/HF) STANDARD (See Page 8 for optional trims)
No. Part Material
ASTM
Spec.
Remarks
1 Handwheel Malleable Iron A47 Gr. 32510
2 Handwheel Nut Steel A108
3 Nameplate Aluminum
4 Operating Nut 410 Stainless Steel A582
5 Stem 410 Stainless Steel A276
6 Gland Nuts 303 Stainless Steel A194 Grade 8F
7 Gland Flange Carbon Steel A108 Grade 1018
8 Gland Carbon Steel B484 Gr. 1, Cl. C, Type 1
9 Eyebolt 410 Stainless Steel Hardened & Tempered
10 Eyebolt Washer Carbon Steel Grade 1018
11a * Packing Graphite Grafoil® (241 or equal)
11b * Wiper Rings Braided Graphite 1630GF or equal
12 Bonnet Bolts Alloy Steel A193 Grade B16
13 Bonnet Chrome Moly A182 Grade F5/F22
14 * Gasket 316 SS/Grafoil® Spiral Wound
15 Seat Cobalt-Chromium Super Alloy CoCr-A
16 Disc 420 Stainless Steel A582 Heat Treated
17 Body Chrome Moly A182 Grade F5/F22
18 Disc Nut 416 Stainless Steel A582
Operating Nut and Stem thread Lubricated
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
DIMENSIONAL SPECIFICATIONS
FLOW
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size
Handwheel End To Center to Port Socket Weld Socket Weld Approximate Typical Cv
Dia. End Top(Open) Dia. Bore
Depth
Weight Factors
1/4 4 3 6-1/4 9/32 .555 .375 4 2.3
3/8 4 3 6-1/4 25/64 .690 .375 4 5.7
1/2 4 3 6-1/4 25/64 .855 .375 4 5.1
3/4 4 3-1/2 6-1/2 ½ 1.065 .500 4-1/2 9.3
1 4-1/2 4-1/8 8-1/2 ¾ 1.330 .500 6-1/2 24.8
1-1/4 5-1/2 4-3/4 9-1/2 1-3/16 1.675 .500 13 67.8
1-1/2 5-1/2 4-3/4 9-1/2 1-3/16 1.915 .500 13 70.9
2 6-5/8 5-1/4 11-1/4 1-15/32 2.406 .625 18 91.6
Disc Design 1 ¼” Thru 2”
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 4GL

RP&C FORGED STEEL GLOBE VALVES
F180D
F380D
F680D
CLASS 150 FLANGED
CLASS 300 FLANGED
CLASS 600 FLANGED
• SIZES ½” THRU 2”
• FORGED STEEL
• ASTM A105N, LOW CARBON (.25 MAX.), NORMALIZED
• STANDARD PORT
• OS&Y – BOLTED BONNET
• WORKING PRESSURE (NON-SHOCK)
CLASS 150
150 PSIG @ 576° F. Steam-Oil
285 PSIG @ -20° To 100° F.
CLASS 300
300 PSIG @ 839° F. Steam-Oil
740 PSIG @ -20° To 100° F.
CLASS 600
600 PSIG @ 576° F. Steam-Oil
1480 PSIG @ -20° To 100° F.
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
D TRIM (13Cr/HF) STANDARD (See Page 8 for optional trims)
No. Part Material
ASTM
Spec.
Remarks
1 Handwheel Malleable Iron A47 Gr. 32510
2 Handwheel Nut Steel A108
3 Nameplate Aluminum
4 Operating Nut Stainless Steel A276 Type 410
5 Stem Stainless Steel A276 Type 410
6 Gland Nuts 303 Stainless Steel A194 Grade 8F
7 Gland Flange Carbon Steel A108 Grade 1018
8 Gland Carbon Steel B484 Gr. 1, Cl. C, Type 1
9 Eyebolt 410 Stainless Steel Hardened & Tempered
10 Eyebolt Washer Carbon Steel Grade 1018
11a * Packing Graphite Grafoil® (241 or equal)
11b * Wiper Rings Braided Graphite 1630GF or equal
12 Bonnet Bolts Alloy Steel A193 Grade B7
13 Bonnet Forged Steel, Normalized A015N Low Carbon
14 * Gasket 316 SS/Grafoil® Spiral Wound
15 Seat Cobalt-Chromium Super Alloy CoCr-A
16 Disc 420 Stainless Steel A582 Heat Treated
17 Body Forged Steel, Normalized A105N Low Carbon
18 Disc Nut 416 Stainless Steel A582
Operating Nut and Stem thread Lubricated
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
DIMENSIONAL SPECIFICATIONS
FLOW
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size
Handwheel Face To Face Center to Port
Approximate Weight
Typical Cv
Dia.
150 300 600
Top(Open) Dia.
150 300 600
Factors
½ 3-7/8 4-1/4 6 6-1/2 6-3/8 3/8 6-3/4 7 8 2.1
¾ 3-7/8 4-5/8 7 7-1/2 6-5/8 ½ 7-1/2 10 11 3.1
1 5-1/2 5 8 8-1/2 8-1/4 ¾ 11 14 15 7.0
1 ½ 5-1/2 6-1/2 9 9-1/2 9-1/4 1-1/4 19 24-1/2 26 18.1
2 6-1/2 8 10-1/2 11-1/2 11 1-1/2 30 38 40 25.2
Disc Design 1 ¼” Thru 2”
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 6GL

F180TF
F380TF
F680TF
RP&C FORGED STEEL GLOBE VALVES
CLASS 150 FLANGED
CLASS 300 FLANGED
CLASS 600 FLANGED
SIZES ¼” THRU 2”
(CHLORINE INSTITUE RECOMMENDS FLANGED ENDS
FOR SIZES OVER 1-1/2” NPS)
FOR CHLORINE SERVICE
• FORGED STEEL
• ASTM A105, LOW CARBON (.25 MAX.), NORMALIZED
• STANDARD PORT
• OS&Y – BOLTED BONNET
• WORKING PRESSURE (NON-SHOCK)
300 PSIG @ -20° To 300° F.
(Class 150 is 230 PSIG @ -20° To 300° F.)
MAX. TEMPERATURE ALLOWABLE FOR CHLORINE SERVICE IS 300°F.
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
• MATERIALS OF CONSTRUCTION
No. Part Material
ASTM
Spec.
Remarks
1 Handwheel Malleable Iron A47 Gr. 32510
2 Handwheel Nut Steel A108
3 Nameplate Aluminum
4 Operating Nut 410 Stainless Steel A582
5 Stem Hastelloy “C” A276
6 Gland Nuts 303 Stainless Steel A194 Grade 8F
7 Gland Flange Carbon Steel A108 Grade 1018
8 Gland Carbon Steel B484 Gr. 1, Cl. C, Type 1
9 Eyebolt 410 Stainless Steel Hardened & Tempered
10 Eyebolt Washer Carbon Steel Grade 1018
11a * Packing Teflon® Chevron Style
12 Bonnet Bolts Alloy Steel A193 Grade B7
13 Bonnet Forged Steel, Normalized A015N Low Carbon
14 * Gasket Monel/Teflon® Spiral Wound
15 Seat Monel Integral
16 Disc Monel/Teflon® Insert B164 Cl. B
17 Body Forged Steel, Normalized A105N Low Carbon
18 Disc Nut Monel B164 Cl. B
Operating Nut and Stem thread Lubricated
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
This valve is designed to meet the service requirements of water
free chlorine service.
The highest quality trim material is used assure trouble free operation in
the paper mill and refinery industry. The body is equipped with an integral
monel seat. The disc holder is monel with a TFE disc. The disc holder is
designed to incorporate a metal-metal seal as a back-up for the TFE disc.
TFE filled, monel spiral gasket and TFE, chevron packing are used for
added sealing assurance.
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size
Handwheel Face To Face Center to Port
Approximate Weight
Typical Cv
Dia.
150 300 600
Top(Open) Dia.
150 300 600
Factors
½ 3-7/8 4-1/4 6 6-1/2 6-3/8 3/8 6-3/4 7 8 2.1
¾ 3-7/8 4-5/8 7 7-1/2 6-5/8 ½ 7-1/2 10 11 3.1
1 5-1/2 5 8 8-1/2 8-1/4 ¾ 11 14 15 7.0
1 ½ 5-1/2 6-1/2 9 9-1/2 9-1/4 1-1/4 19 24-1/2 26 18.1
2 6-1/2 8 10-1/2 11-1/2 11 1-1/2 30 38 40 25.2
Disc Design 1 ¼” Thru 2”
FLOW
MINIMUM QUANTITIES MAY BE REQUIRED
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 8GL

RP&C VALVES – CLASS 1500
F580E NPT ENDS
F581E
SOCKET WELD ENDS
SIZES 1/2” THRU 2”
• FORGED STEEL GLOBE VALVE
• ASTM A105N LOW CARBON (.25 MAX.), NORMALIZED
• STANDARD PORT
• OS&Y – BOLTED BONNET
• WORKING PRESSURE (NON-SHOCK)
860 PSIG @ 900° F. Steam-Oil
1340 PSIG @ 850° F. Steam-Oil
3705 PSIG @ -20° To 100° F.
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 591 API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
E TRIM (13 Cr/FHF) STANDARD (See Page 8 for optional trims)
No. Part Material
ASTM
Spec.
Remarks
1 Handwheel Malleable Iron A47 Gr. 32510
2 Handwheel Nut Steel A108
3 Nameplate Aluminum
4 Operating Nut 416 Stainless Steel A582
5 Stem 416 Stainless Steel A582
6 Gland Nuts 303 Stainless Steel A194 Grade 8F
7 Gland Plate Forged Carbon Steel A105
8 Gland Carbon Steel B484 Gr. 2, Cl. C, Type 1
9 Eyebolt 410 Stainless Steel Hardened & Tempered
10 Eyebolt Washer Stainless Steel 300 Series
11 * Packing Graphite Grafoil® (241 or equal)
11a * Wiper Rings Braided Graphite 1630GF or equal
12 Bonnet Bolts Alloy Steel A193 Grade B7
13 Bonnet Forged Steel, Normalized A015N Low Carbon
14 * Gasket 316 SS/Grafoil® Spiral Wound
15 Seat Cobalt-Chromium Super Alloy CoCr-A
16 Disc Cobalt-Chromium Super Alloy CoCr-A
17 Body Forged Steel, Normalized A105N Low Carbon
Operating Nut and Stem thread Lubricated
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size
Handwheel End To Center to
Socket Weld Socket Weld Approximate Typical Cv
Port
Dia. End Top(Open)
Bore
Depth
Weight Factors
1/2 4-1/2 4 8-1/4 25/64 .855 .375 7-1/4 2.1
3/4 4-1/2 4 8-1/4 1/2 1.065 .500 8-1/4 3.1
1 5-1/2 5-1/2 9 3/4 1.330 .500 13-1/4 7.0
1-1/2 6-5/8 6-1/2 10-5/8 1-3/16 1.915 .500 24-3/4 18.1
2 8-1/4 7 12-1/4 1-15/32 2.406 .625 39-1/2 25.2
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 5 V15

RP&C FORGED STEEL GLOBE VALVES
F80D NPT ENDS SIZES ¼” THRU 2”
F81D SOCKET WELD ENDS
• FORGED STEEL
• ASTM A105, LOW CARBON (.25 MAX.), NORMALIZED
• STANDARD PORT
• OS&Y – BOLTED BONNET
• WORKING PRESSURE (NON-SHOCK)
460 PSIG @ 900° F. Steam-Oil
715 PSIG @ 850° F. Steam-Oil
1975 PSIG @ -20° To 100° F.
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
D TRIM (13 Cr/HF) STANDARD (See Page 8 for optional trims)
No. Part Material
ASTM
Spec.
Remarks
1 Handwheel Malleable Iron A47 Gr. 32510
2 Handwheel Nut Steel A108
3 Nameplate Aluminum
4 Operating Nut Stainless Steel A276 Type 410
5 Stem Stainless Steel A276 Type 410
6 Gland Nuts 303 Stainless Steel A194 Grade 8F
7 Gland Flange Carbon Steel A108 Grade 1018
8 Gland Carbon Steel B484 Gr. 1, Cl. C, Type 1
9 Eyebolt 410 Stainless Steel Hardened & Tempered
10 Eyebolt Washer Carbon Steel Grade 1018
11a * Packing Graphite Grafoil® (241 or equal)
11b * Wiper Rings Braided Graphite 1630GF or equal
12 Bonnet Bolts Alloy Steel A193 Grade B7
13 Bonnet Forged Steel, Normalized A015N Low Carbon
14 * Gasket 316 SS/Grafoil® Spiral Wound
15 Seat Cobalt-Chromium Super Alloy CoCr-A
16 Disc 420 Stainless Steel A582 Heat Treated
17 Body Forged Steel, Normalized A105N Low Carbon
18 Disc Nut 416 Stainless Steel A582
Operating Nut and Stem thread Lubricated
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
FLOW
Disc Design 1 ¼” Thru 2”
Disc Design 1 ¼” Thru 2”
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size
Handwheel End To Center to Port Socket Weld Socket Weld Approximate Typical Cv
Dia. End Top(Open) Dia. Bore
Depth
Weight Factors
1/4 3-7/8 3 6-3/8 9/32 .555 .375 4 1.1
3/8 3-7/8 3 6-3/8 5/16 .690 .375 4 1.6
1/2 3-7/8 3 6-3/8 3/8 .855 .375 4 2.1
3/4 3-7/8 3-1/2 6-5/8 ½ 1.065 .500 4-1/2 3.1
1 5-1/2 4-3/8 8-1/4 ¾ 1.330 .500 7 7.0
1-1/4 5-1/2 6 9-1/4 1 1.675 .500 14 15.4
1-1/2 5-1/2 6 9-1/4 1-1/4 1.915 .500 13-1/2 18.1
2 6-1/2 7 11 1-1/2 2.406 .625 19 25.2
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 1GL

RP&C VALVES – CLASS 1500
FWB580E NPT ENDS
FWB581E
SIZES 1/2” THRU 2”
SOCKET WELD ENDS
• FORGED STEEL GLOBE VALVE
• ASTM A105N LOW CARBON (.25 MAX.), NORMALIZED
• STANDARD PORT
• OS&Y – WELDED BONNET
• WORKING PRESSURE (NON-SHOCK)
860 PSIG @ 900° F. Steam-Oil
1340 PSIG @ 850° F. Steam-Oil
3705 PSIG @ -20° To 100° F.
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 591 API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
E TRIM (13 Cr/FHF) STANDARD (See Page 8 for optional trims)
No. Part Material
ASTM
Spec.
Remarks
1 Handwheel Malleable Iron A47 Gr. 32510
2 Handwheel Nut Steel A108
3 Nameplate Aluminum
4 Operating Nut 416 Stainless Steel A582
5 Stem 416 Stainless Steel A582
6 Gland Nuts 303 Stainless Steel A194 Grade 8F
7 Gland Plate Forged Carbon Steel A105
8 Gland Carbon Steel B484 Gr. 1, Cl. C, Type 1
9 Eyebolt 410 Stainless Steel Hardened & Tempered
10 Eyebolt Washer Stainless Steel 300 Series
11 * Packing Graphite Grafoil® (241 or equal)
11a * Wiper Rings Braided Graphite 1630GF or equal
12 Bonnet Forged Steel, Normalized A015N Low Carbon
13 Seat Cobalt-Chromium Super Alloy CoCr-A
14 Disc Cobalt-Chromium Super Alloy CoCr-A
15 Body Forged Steel, Normalized A105N Low Carbon
Operating Nut and Stem thread Lubricated
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size
Handwheel End To Center to
Socket Weld Socket Weld Approximate Typical Cv
Port
Dia. End Top(Open)
Bore
Depth
Weight Factors
1/2 4-1/2 4 8-1/4 25/64 .855 .375 7-1/4 2.1
3/4 4-1/2 4 8-1/4 1/2 1.065 .500 8-1/4 3.1
1 5-1/2 5-1/2 9 3/4 1.330 .500 13-1/4 7.0
1-1/2 6-5/8 6-1/2 10-5/8 1-3/16 1.915 .500 24-3/4 18.1
2 8-1/4 7 12-1/4 1-15/32 2.406 .625 39-1/2 25.2
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 6 V15

RP&C FORGED STEEL GLOBE VALVES
FWB80D NPT ENDS SIZES ¼” THRU 2”
FWB81D SOCKET WELD ENDS
• FORGED STEEL
• ASTM A105, LOW CARBON (.25 MAX.), NORMALIZED
• STANDARD PORT
• OS&Y – WELDED BONNET
• WORKING PRESSURE (NON-SHOCK)
460 PSIG @ 900° F. Steam-Oil
715 PSIG @ 850° F. Steam-Oil
1975 PSIG @ -20° To 100° F.
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
Disc Design 1 ¼” Thru 2”
• MATERIALS OF CONSTRUCTION
D TRIM (13 Cr/HF) STANDARD (See Page 8 for optional trims)
No. Part Material
ASTM
Spec.
Remarks
1 Handwheel Malleable Iron A47 Gr. 32510
2 Handwheel Nut Steel A108
3 Nameplate Aluminum
4 Operating Nut Stainless Steel A276 Type 410
5 Stem Stainless Steel A276 Type 410
6 Gland Nuts 303 Stainless Steel A194 Grade 8F
7 Gland Flange Carbon Steel A108 Grade 1018
8 Gland Carbon Steel B484 Gr. 1, Cl. C, Type 1
9 Eyebolt 410 Stainless Steel Hardened & Tempered
10 Eyebolt Washer Carbon Steel Grade 1018
11a * Packing Graphite Grafoil® (241 or equal)
11b * Wiper Rings Braided Graphite 1630GF or equal
12 Bonnet Forged Steel, Normalized A105N Low Carbon
13 Seat Cobalt-Chromium Super Alloy CoCr-A
14 Disc 420 Stainless Steel A582 Heat Treated
15 Body Forged Steel, Normalized A105N Low Carbon
16 Disc Nut 416 Stainless Steel A582
Operating Nut and Stem thread Lubricated
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
FLOW
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size
Handwheel End To Center to Port Socket Weld Socket Weld Approximate Typical Cv
Dia. End Top(Open) Dia. Bore
Depth
Weight Factors
1/4 3-7/8 3 6-3/8 9/32 .555 .375 4 1.1
3/8 3-7/8 3 6-3/8 5/16 .690 .375 4 1.6
1/2 3-7/8 3 6-3/8 3/8 .855 .375 4 2.1
3/4 3-7/8 3-1/2 6-5/8 ½ 1.065 .500 4-1/2 3.1
1 5-1/2 4-3/8 8-1/4 ¾ 1.330 .500 7 7.0
1-1/4 5-1/2 6 9-1/4 1 1.675 .500 14 15.4
1-1/2 5-1/2 6 9-1/4 1-1/4 1.915 .500 13-1/2 18.1
2 6-1/2 7 11 1-1/2 2.406 .625 19 25.2
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 2GL

RP&C FORGED STEEL GLOBE VALVES
K1200E SIZES 1/4” THRU 1-1/2” NPT
K1210E SIZES 1/4” THRU 2-1/2” SOCKET WELD
K1220E SIZES 1/4” THRU 4” BUTT WELD
• FORGED STEEL ASTM A182 Gr. F22 Cl. 3
(2-1/4% Chrome, 1% Moly)
• OS&Y GLOBE VALVE, INCLINED STEM
• INTEGRAL BACKSEAT
• SEAL WELDED BONNET
• REFER TO CHART ON PAGE 2Y FOR PRESSURE/TEMP. RATINGS
(NOT RECOMMENDED FOR PROLONGED USE ABOVE 1100 F°)
• CONFORMS TO THE APPLICABLE PARTS OF THE
FOLLOWING ASME/ANSI SPECIFICATIONS:
B16.34
B31.3
B1.20.1 SCREWED ENDS
B16.11 SOCKET WELD ENDS
B16.25 BUTT WELD ENDS
MATERIALS OF CONSTRUCTION
NO. PART MATERIAL
ASTM
SPEC.
REMARKS
1 Body Forged Steel A182 Grade F22 Cl. 3
2 Seat Ring Cobalt-Chromium Super Alloy CoCr-A
3 Bonnet Forged Steel A182 Grade F22 Cl. 3
4 Operating Nut Bronze B150 Alloy 642
5 Gland Stainless Steel A582 Type 416
6 Gland Flange Alloy Steel A29 Grade 4140
7a * Packing Grafoil ® Crane 241
7b * Wiper rings Graphite Yarn Crane 1625GF
8 Stem Assembly
416 Stainless Steel A582 Stem
CoCr-A
Disc
9 Eyebolt Alloy Steel A193 Grade B7
10 Eyebolt Pin Alloy Steel A29 Grade 4140
11 Gland Nut Steel A194 Grade 2H
12 Handwheel Malleable Iron A47 Grade 32510
13 Nameplate Aluminum
14 Handwheel Nut Steel A108 Zinc Plated
* RECOMMENDED SPARE PARTS
Round handwheels are standard thru 1”. Impactor handles are
standard on 1-1/4” and larger.
FLOW
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size
Handwheel End To Center to
Socket Weld Socket Weld Approximate Typical Cv
Port
Dia. End Top(Open)
Bore
Depth
Weight Factors
1/4 6-1/2 4-1/2 9-5/32 5-16 .555 .375 9-1/2 2.0
3/8 6-1/2 4-1/2 9-5/32 3/8 .690 .375 9-1/2 2.5
1/2 6-1/2 4-1/2 9-5/32 7/16 .855 .375 9-1/2 3.5
3/4 6-1/2 5-7/16 11-5/32 9/16 1.065 .500 15-3/4 5.6
1 7-3/8 5-7/16 11-5/32 13/16 1.330 .500 15-3/4 12.7
1-1/4 13-1/2 8-1/4 14-29/32 1-1/8 1.675 .500 39 26.0
1-1/2 13-1/2 8-1/4 14-29/32 1-1/4 1.915 .500 39 35.0
2 13-1/2 9-1/2 17-1/16 1-9/16 2.406 .625 65-1/2 46.0
2-1/2” 20 12-3/4 25-5/8 2 -- -- 180 95.0
3” & 4” 20 12-3/4 25-5/8 2 -- -- 180 95.0
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 4Y

RP&C FORGED STEEL GLOBE VALVES
K1202E SIZES 1/4” THRU 1-1/2” NPT
K1212E SIZES 1/4” THRU 2-1/2” SOCKET WELD
K1222E SIZES 1/4” THRU 4” BUTT WELD
• FORGED STEEL ASTM A182 Gr. F22 Cl. 3
(2-1/4% Chrome, 1% Moly)
• OS&Y GLOBE VALVE, INCLINED STEM
• LOOSE BACKSEAT
• SEAL WELDED BONNET
• REFER TO CHART ON PAGE 2Y FOR PRESSURE/TEMP. RATINGS
(NOT RECOMMENDED FOR PROLONGED USE ABOVE 1100 F°)
• CONFORMS TO THE APPLICABLE PARTS OF THE
FOLLOWING ASME/ANSI SPECIFICATIONS:
B16.34
B31.3
B1.20.1 SCREWED ENDS
B16.11 SOCKET WELD ENDS
B16.25 BUTT WELD ENDS
NO. PART MATERIAL
MATERIALS OF CONSTRUCTION
ASTM
SPEC.
REMARKS
1 Body Forged Steel A182 Grade F22 Cl. 3
2 Seat Ring Cobalt-Chromium Super Alloy CoCr-A
3 Bonnet Forged Steel A182 Grade F22 Cl. 3
4 Operating Nut Bronze B150 Alloy 642
5 Gland Stainless Steel A582 Type 416
6 Gland Flange Alloy Steel A29 Grade 4140
7a * Packing Grafoil ® Crane 241
7b * Wiper rings Graphite Yarn Crane 1625GF
8 Stem Assembly
416 Stainless Steel A582 Stem
CoCr-A
Disc
9 Eyebolt Alloy Steel A193 Grade B7
10 Eyebolt Pin Alloy Steel A29 Grade 4140
11 Gland Nut Steel A194 Grade 2H
12 Handwheel Malleable Iron A47 Grade 32510
13 Nameplate Aluminum
14 Handwheel Nut Steel A108 Zinc Plated
15 * Loose Backseat Stainless Steel A582 Type 416
16 Retainer Stainless Steel A582 Type 416
* RECOMMENDED SPARE PARTS
Round handwheels are standard thru 1”. Impactor handles are
standard on 1-1/4” and larger.
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size
Handwheel End To Center to
Socket Weld Socket Weld Approximate Typical Cv
Port
Dia. End Top(Open)
Bore
Depth
Weight Factors
1/4 6-1/2 4-1/2 9-5/32 5-16 .555 .375 9-1/2 2.0
3/8 6-1/2 4-1/2 9-5/32 3/8 .690 .375 9-1/2 2.5
1/2 6-1/2 4-1/2 9-5/32 7/16 .855 .375 9-1/2 3.5
3/4 6-1/2 5-7/16 11-5/32 9/16 1.065 .500 15-3/4 5.6
1 7-3/8 5-7/16 11-5/32 13/16 1.330 .500 15-3/4 12.7
1-1/4 13-1/2 8-1/4 14-29/32 1-1/8 1.675 .500 39 26.0
1-1/2 13-1/2 8-1/4 14-29/32 1-1/4 1.915 .500 39 35.0
2 13-1/2 9-1/2 17-1/16 1-9/16 2.406 .625 65-1/2 46.0
2-1/2” 20 12-3/4 25-5/8 2 -- -- 180 95.0
3” & 4” 20 12-3/4 25-5/8 2 -- -- 180 95.0
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 6Y

RP&C FORGED STEEL GLOBE VALVES
K1250E SIZES 1/4” THRU 1-1/2” NPT (CLASS 2500)*
K1260E SIZES 1/4” THRU 2-1/2” SOCKET WELD
K1270E SIZES 1/4” THRU 3” BUTT WELD
• FORGED STEEL ASTM A182 Gr. F22 Cl. 3
(2-1/4% Chrome, 1% Moly)
• OS&Y GLOBE VALVE, INCLINED STEM
• INTEGRAL BACKSEAT
• SEAL WELDED BONNET
• REFER TO CHART ON PAGE 2Y FOR PRESSURE/TEMP. RATINGS
(NOT RECOMMENDED FOR PROLONGED USE ABOVE 1100 F°)
• CONFORMS TO THE APPLICABLE PARTS OF THE
FOLLOWING ASME/ANSI SPECIFICATIONS:
B16.34
B31.3
B1.20.1 SCREWED ENDS
B16.11 SOCKET WELD ENDS
B16.25 BUTT WELD ENDS
NO. PART MATERIAL
MATERIALS OF CONSTRUCTION
ASTM
SPEC.
REMARKS
1 Body Forged Steel A182 Grade F22 Cl. 3
2 Seat Ring Cobalt-Chromium Super Alloy CoCr-A
3 Bonnet Forged Steel A182 Grade F22 Cl. 3
4 Operating Nut Bronze B150 Alloy 642
5 Gland Stainless Steel A582 Type 416
6 Gland Flange Alloy Steel A29 Grade 4140
7a * Packing Grafoil ® Crane 241
7b * Wiper rings Graphite Yarn Crane 1625GF
8 Stem Assembly
416 Stainless Steel A582 Stem
CoCr-A
Disc
9 Eyebolt Alloy Steel A193 Grade B7
10 Eyebolt Pin Alloy Steel A29 Grade 4140
11 Gland Nut Steel A194 Grade 2H
12 Handwheel Malleable Iron A47 Grade 32510
13 Nameplate Aluminum
14 Handwheel Nut Steel A108 Zinc Plated
* RECOMMENDED SPARE PARTS
Round handwheels are standard thru 1”. Impactor handles are
standard on 1-1/4” and larger.
FLOW
ASME B16.34 DOES NOT ALLOW FOR THREADED ENDS
ABOVE CLASS 2500
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size
Handwheel End To Center to
Socket Weld Socket Weld Approximate Typical Cv
Port
Dia. End Top(Open)
Bore
Depth
Weight Factors
1/4 6-1/2 4-1/2 9-5/32 5-16 .555 .375 9-1/2 2.0
3/8 6-1/2 4-1/2 9-5/32 3/8 .690 .375 9-1/2 2.5
1/2 6-1/2 4-1/2 9-5/32 7/16 .855 .375 9-1/2 3.5
3/4 6-1/2 5-7/16 11-5/32 9/16 1.065 .500 15-3/4 5.6
1 7-3/8 5-7/16 11-5/32 13/16 1.330 .500 15-3/4 12.7
1-1/4 13-1/2 8-1/4 14-29/32 1-1/8 1.675 .500 39 26.0
1-1/2 13-1/2 8-1/4 14-29/32 1-1/4 1.915 .500 39 35.0
2 13-1/2 9-1/2 17-1/16 1-9/16 2.406 .625 65-1/2 46.0
2-1/2” 20 12-3/4 25-5/8 2 -- -- 180 95.0
3” & 4” 20 12-3/4 25-5/8 2 -- -- 180 95.0
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 8Y

RP&C FORGED STEEL GLOBE VALVES
K1252E SIZES 1/4” THRU 1-1/2” NPT (CLASS 2500)*
K1262E SIZES 1/4” THRU 2-1/2” SOCKET WELD
K1272E SIZES 1/4” THRU 3” BUTT WELD
• FORGED STEEL ASTM A182 Gr. F22 Cl. 3
(2-1/4% Chrome, 1% Moly)
• OS&Y GLOBE VALVE, INCLINED STEM
• LOOSE BACKSEAT
• SEAL WELDED BONNET
• REFER TO CHART ON PAGE 2Y FOR PRESSURE/TEMP. RATINGS
(NOT RECOMMENDED FOR PROLONGED USE ABOVE 1100 F°)
• CONFORMS TO THE APPLICABLE PARTS OF THE
FOLLOWING ASME/ANSI SPECIFICATIONS:
B16.34
B31.3
B1.20.1 SCREWED ENDS
B16.11 SOCKET WELD ENDS
B16.25 BUTT WELD ENDS
MATERIALS OF CONSTRUCTION
NO. PART MATERIAL
ASTM
SPEC.
1 Body Forged Steel A105
REMARKS
2 Seat Ring Cobalt-Chromium Super Alloy CoCr-A
3 Bonnet Forged Steel A105
4 Operating Nut Bronze B150 Alloy 642
5 Gland Stainless Steel A582 Type 416
6 Gland Flange Alloy Steel A29 Grade 4140
7a * Packing Grafoil ® Crane 241
7b * Wiper rings Graphite Yarn Crane 1625GF
8 Stem Assembly
416 Stainless Steel A582 Stem
CoCr-A
9 Eyebolt Alloy Steel A193 Grade B7
10 Eyebolt Pin Alloy Steel A29 Grade 4140
11 Gland Nut Steel A194 Grade 2H
12 Handwheel Malleable Iron A47 Grade 32510
13 Nameplate Aluminum
14 Handwheel Nut Steel A108 Zinc Plated
15 * Loose Backseat Stainless Steel A582 Type 416
16 Retainer Stainless Steel A582 Type 416
* RECOMMENDED SPARE PARTS
Round handwheels are standard thru 1”. Impactor handles are
standard on 1-1/4” and larger.
Disc
ASME B16.34 DOES NOT ALLOW FOR THREADED ENDS
ABOVE CLASS 2500
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size
Handwheel End To Center to
Socket Weld Socket Weld Approximate Typical Cv
Port
Dia. End Top(Open)
Bore
Depth
Weight Factors
1/4 6-1/2 4-1/2 9-5/32 5-16 .555 .375 9-1/2 2.0
3/8 6-1/2 4-1/2 9-5/32 3/8 .690 .375 9-1/2 2.5
½ 6-1/2 4-1/2 9-5/32 7/16 .855 .375 9-1/2 3.5
¾ 6-1/2 5-7/16 11-5/32 9/16 1.065 .500 15-3/4 5.6
1 7-3/8 5-7/16 11-5/32 13/16 1.330 .500 15-3/4 12.7
1-1/4 13-1/2 8-1/4 14-29/32 1-1/8 1.675 .500 39 26.0
1-1/2 13-1/2 8-1/4 14-29/32 1-1/4 1.915 .500 39 35.0
2 13-1/2 9-1/2 17-1/16 1-9/16 2.406 .625 65-1/2 46.0
2-1/2” 20 12-3/4 25-5/8 2 -- -- 180 95.0
3” & 4” 20 12-3/4 25-5/8 2 -- -- 180 95.0
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 10Y

RP&C FORGED STEEL GLOBE VALVES
LF80D NPT ENDS SIZES ¼” THRU 2”
LF81D SOCKET WELD ENDS
• FORGED STEEL
• ASTM A350 Gr. LF2
• STANDARD PORT
• OS&Y – BOLTED BONNET
• WORKING PRESSURE (NON-SHOCK)
1100 PSIG @ 800° F. Steam-Oil
1975 PSIG @ -20° To 100° F
800°F. IS MAX. OPERATING TEMP. FOR LF2
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
Disc Design 1 ¼” Thru 2”
• MATERIALS OF CONSTRUCTION
D TRIM (13 Cr/HF) STANDARD (See Page 8 for optional trims)
No. Part Material
ASTM
Spec.
Remarks
1 Handwheel Malleable Iron A47 Gr. 32510
2 Handwheel Nut Steel A108
3 Nameplate Aluminum
4 Operating Nut Stainless Steel A276 Type 410
5 Stem Stainless Steel A276 Type 410
6 Gland Nuts 303 Stainless Steel A194 Grade 8F
7 Gland Flange Carbon Steel A108 Grade 1018
8 Gland Carbon Steel B484 Gr. 1, Cl. C, Type 1
9 Eyebolt 410 Stainless Steel Hardened & Tempered
10 Eyebolt Washer Carbon Steel Grade 1018
11a * Packing Graphite Grafoil® (241 or equal)
11b * Wiper Rings Braided Graphite 1630GF or equal
12 Bonnet Bolts Alloy Steel A193 Grade B8M Cl.2
13 Bonnet Forged Steel A350 Gr. LF2
14 * Gasket 316 SS/Grafoil® Spiral Wound
15 Seat Cobalt-Chromium Super Alloy CoCr-A
16 Disc 420 Stainless Steel A582 Heat Treated
17 Body Forged Steel A350 Gr. LF2
18 Disc Nut 416 Stainless Steel A582
Operating Nut and Stem thread Lubricated
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
FLOW
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size
Handwheel End To Center to Port Socket Weld Socket Weld Approximate Typical Cv
Dia. End Top(Open) Dia. Bore
Depth
Weight Factors
1/4 3-7/8 3 6-3/8 9/32 .555 .375 4 1.1
3/8 3-7/8 3 6-3/8 5/16 .690 .375 4 1.6
1/2 3-7/8 3 6-3/8 3/8 .855 .375 4 2.1
3/4 3-7/8 3-1/2 6-5/8 ½ 1.065 .500 4-1/2 3.1
1 5-1/2 4-3/8 8-1/4 ¾ 1.330 .500 7 7.0
1-1/4 5-1/2 6 9-1/4 1 1.675 .500 14 15.4
1-1/2 5-1/2 6 9-1/4 1-1/4 1.915 .500 13-1/2 18.1
2 6-1/2 7 11 1-1/2 2.406 .625 19 25.2
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 3GL

RP&C FORGED STEEL GATE VALVES
EFO56D NPT ENDS SIZES ¼” THRU 2”
EFO57D SOCKET WELD ENDS
• FORGED STEEL
• ASTM A105N LOW CARBON (.25 MAX.), NORMALIZED
• FULL PORT
• OS&Y – BOLTED BONNET
• WORKING PRESSURE (NON-SHOCK)
460 PSIG @ 900° F. Steam-Oil
715 PSIG @ 850° F. Steam-Oil
1975 PSIG @ -20° To 100° F.
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 591 API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
D TRIM (13 Cr/HF) STANDARD (See Page 8 for optional trims)
No. Part Material
ASTM
Spec.
Remarks
1 Handwheel Malleable Iron A47 Gr. 32510
2 Handwheel Nut Steel A108
3
Internal Tooth
Lockwasher
Steel
4 Nameplate Aluminum
5 Thrust Washer Stainless Steel Hardened
6 Operating Nut 416 Stainless Steel A582
7 Stem 410 Stainless Steel A276
8 Gland Nuts 303 Stainless Steel A194 Grade 8F
9 Gland Flange Carbon Steel A108 Grade 1018
10 Gland Carbon Steel B484 Gr. 1, Cl. C, Type 1
11 Eyebolt 410 Stainless Steel Hardened & Tempered
12 Eyebolt Washer Carbon Steel Grade 1018
13a * Packing Graphite Grafoil® (241 or equal)
13b * Wiper Rings Braided Graphite 1630GF or equal
14 Bonnet Bolts Alloy Steel A193 Grade B7
15 Bonnet Forged Steel, Normalized A015N Low Carbon
16 * Gasket 316 SS/Grafoil® Spiral Wound
17 Seat Rings 410 Stainless Steel A276 Hard Faced
18 Wedge CA-15 Stainless Steel A217 Heat Treated
19 Body Forged Steel, Normalized A105N Low Carbon
Operating Nut and Stem thread Lubricated
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
Size
DIMENSIONAL SPECIFICATIONS
Handwheel
Dia.
End To
End
Center to
Top(Open)
Port
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Socket Weld
Bore
Socket Weld
Depth
Approximate
Weight
Typical Cv
Factors
1/4 4 3 6-1/4 9/32 .555 .375 4 2.3
3/8 4 3 6-1/4 25/64 .690 .375 4 5.7
1/2 4 3-1/2 6-1/2 1/2 .855 .375 4-1/2 9.3
3/4 4-1/2 4-1/8 8-1/2 3/4 1.065 .500 6-1/2 24.8
1 5-1/2 4-3/4 9-1/2 1” 1.330 .500 13 67.8
1-1/4 5-1/2 4-3/4 9-1/2 1-3/16 1.675 .500 13-1/2 70.9
1-1/2 6-5/8 5-1/4 11-1/4 1-15/32 1.915 .500 18-1/2 91.6
2 8-3/8 5-5/8 13 2” 2.406 .625 25-1/2 200.0
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 2G

RP&C FORGED STEEL GATE VALVES
EF158D CLASS 150 FLANGED
EF308D CLASS 300 FLANGED
EF608D CLASS 600 FLANGED
• SIZES ¼” THRU 2”
• FORGED STEEL
• ASTM A105N LOW CARBON (.25 MAX.), NORMALIZED
• STANDARD PORT
• OS&Y – BOLTED BONNET
• WORKING PRESSURE (NON-SHOCK)
CLASS 150
150 PSIG @ 576° F. Steam-Oil
285 PSIG @ -20° To 100° F.
CLASS 300
300 PSIG @ 839° F. Steam-Oil
740 PSIG @ -20° To 100° F.
CLASS 600
600 PSIG @ 576° F. Steam-Oil
1480 PSIG @ -20° To 100° F.
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 591 API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
D TRIM (13 Cr/HF) STANDARD (See Page 8 for optional trims)
No. Part Material
ASTM
Spec.
Remarks
1 Handwheel Malleable Iron A47 Gr. 32510
2 Handwheel Nut Steel A108
3
Internal Tooth
Lockwasher
Steel
4 Nameplate Aluminum
5 Thrust Washer Stainless Steel Hardened
6 Operating Nut 416 Stainless Steel A582
7 Stem 410 Stainless Steel A276
8 Gland Nuts 303 Stainless Steel A194 Grade 8F
9 Gland Flange Carbon Steel A108 Grade 1018
10 Gland Carbon Steel B484 Gr. 1, Cl. C, Type 1
11 Eyebolt 410 Stainless Steel Hardened & Tempered
12 Eyebolt Washer Carbon Steel Grade 1018
13a * Packing Graphite Grafoil® (241 or equal)
13b * Wiper Rings Braided Graphite 1630GF or equal
14 Bonnet Bolts Alloy Steel A193 Grade B7
15 Bonnet Forged Steel, Normalized A015N Low Carbon
16 * Gasket 316 SS/Grafoil® Spiral Wound
17 Seat Rings 410 Stainless Steel A276 Hard Faced
18 Wedge CA-15 Stainless Steel A217 Heat Treated
19 Body Forged Steel, Normalized A105N Low Carbon
Operating Nut and Stem thread Lubricated
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size
Handwheel End To End Center to
Port
Approximate Weight Typical Cv
Dia. 150 300 600 Top(Open)
150 300 600 Factors
1/2 4 4-1/4 5-1/2 6-1/2 6-1/4 25/64 6-3/4 7-1/2 8 5.1
3/4 4 4-5/8 6 7-1/2 6-1/2 1/2 7-1/2 10 11 9.3
1 4-1/2 5 6-1/2 8-1/2 8-1/2 3/4 11 12 13 24.8
1-1/2 5-1/2 6-1/2 7-1/2 9-1/2 9-1/2 1-3/16 19 23 27 67.8
2 6-5/8 7 8-1/2 11-1/2 11-1/4 1-15/32 29 36 39 70.9
3 8-3/8 8 11-1/8 14 13 2 50 63 68 91.6
DIMENSIONAL SPECIFICATIONS
NOTE: Class 150 Flanged valves feature integrally
forged flanges.
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 8G

RP&C FORGED STEEL GATE VALVES
EF46D
EF51D
EF52D
EF53D
EF54D
EF55D
MALE COUPLET X FEMALE SOCKET WELD
MALE X FEMALE NPT
MALE X FEMALE SOCKET WELD
MALE NPT X FEMALE SOCKET WELD
MALE SOCKET WELD X FEMALE NPT
MALE COUPLET X FEMALE NPT
• SIZES 1/2” THRU 1 1 / 2”
NOTE: 1/2” MALE THREADS ARE NOT COVERED BY API 602
• FORGED STEEL
• ASTM A105N LOW CARBON (.25 MAX.), NORMALIZED
• STANDARD PORT
• OS&Y – BOLTED BONNET
• WORKING PRESSURE (NON-SHOCK)
460 PSIG @ 900° F. Steam-Oil
715 PSIG @ 850° F. Steam-Oil
1975 PSIG @ -20° To 100° F.
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 591 API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
D TRIM (13 Cr/HF) STANDARD (See Page 8 for optional trims)
No. Part Material
ASTM
Spec.
Remarks
1 Handwheel Malleable Iron A47 Gr. 32510
2 Handwheel Nut Steel A108
3
Internal Tooth
Lockwasher
Steel
4 Nameplate Aluminum
5 Thrust Washer Stainless Steel Hardened
6 Operating Nut 416 Stainless Steel A582
7 Stem 410 Stainless Steel A276
8 Gland Nuts 303 Stainless Steel A194 Grade 8F
9 Gland Flange Carbon Steel A108 Grade 1018
10 Gland Carbon Steel B484 Gr. 1, Cl. C, Type 1
11 Eyebolt 410 Stainless Steel Hardened & Tempered
12 Eyebolt Washer Carbon Steel Grade 1018
13a * Packing Graphite Grafoil® (241 or equal)
13b * Wiper Rings Braided Graphite 1630GF or equal
14 Bonnet Bolts Alloy Steel A193 Grade B7
15 Bonnet Forged Steel, Normalized A015N Low Carbon
16 * Gasket 316 SS/Grafoil® Spiral Wound
17 Seat Rings 410 Stainless Steel A276 Hard Faced
18 Wedge CA-15 Stainless Steel A217 Heat Treated
19 Body Forged Steel, Normalized A105N Low Carbon
Operating Nut and Stem thread Lubricated
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
MINIMUM QUANTITIES MAY BE REQUIRED
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size
Handwheel End To Center to
Socket Weld Socket Weld Approximate Typical Cv
Port
Dia. End Top(Open)
Bore
Depth
Weight Factors
1/2 4 5-9/16 6-1/4 25/64 .855 .375 4-1/2 5.1
3/4 4 6 6-1/2 1/2 1.065 .500 4-3/4 9.3
1 4-1/2 6-5/16 8-1/2 3/4 1.330 .500 6-3/4 24.8
1-1/2 5-1/2 7-7/16 9-1/2 1-1/4 1.915 .500 14 70.9
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 9G

EF48D
EF49D
RP&C FORGED STEEL GATE VALVES
MALE SOCKET WELD X FEMALE NPT
MALE X FEMALE SOCKET WELD
• INTEGRALLY REINFORCED MALE END
• SIZES 1/2” THRU 2”
• FORGED STEEL
• ASTM A105N LOW CARBON (.25 MAX.), NORMALIZED
• STANDARD PORT
• OS&Y – BOLTED BONNET
• WORKING PRESSURE (NON-SHOCK)
460 PSIG @ 900° F. Steam-Oil
715 PSIG @ 850° F. Steam-Oil
1975 PSIG @ -20° To 100° F.
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 591 API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
D TRIM (13 Cr/HF) STANDARD (See Page 8 for optional trims)
No. Part Material
ASTM
Spec.
Remarks
1 Handwheel Malleable Iron A47 Gr. 32510
2 Handwheel Nut Steel A108
3
Internal Tooth
Lockwasher
Steel
4 Nameplate Aluminum
5 Thrust Washer Stainless Steel Hardened
6 Operating Nut 416 Stainless Steel A582
7 Stem 410 Stainless Steel A276
8 Gland Nuts 303 Stainless Steel A194 Grade 8F
9 Gland Flange Carbon Steel A108 Grade 1018
10 Gland Carbon Steel B484 Gr. 1, Cl. C, Type 1
11 Eyebolt 410 Stainless Steel Hardened & Tempered
12 Eyebolt Washer Carbon Steel Grade 1018
13a * Packing Graphite Grafoil® (241 or equal)
13b * Wiper Rings Braided Graphite 1630GF or equal
14 Bonnet Bolts Alloy Steel A193 Grade B7
15 Bonnet Forged Steel, Normalized A015N Low Carbon
16 * Gasket 316 SS/Grafoil® Spiral Wound
17 Seat Rings 410 Stainless Steel A276 Hard Faced
18 Wedge CA-15 Stainless Steel A217 Heat Treated
19 Body Forged Steel, Normalized A105N Low Carbon
Operating Nut and Stem thread Lubricated
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
MINIMUM QUANTITIES MAY BE REQUIRED
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size
Handwheel End To Center to
Socket Weld Socket Weld Approximate Typical Cv
Port
Dia. End Top(Open)
Bore
Depth
Weight Factors
1/2 4 7-5/8 6-1/4 25/64 .855 .375 5-1/2 5.1
3/4 4 8-11/16 6-1/2 1/2 1.065 .500 6-1/2 9.3
1 4-1/2 9-11/16 8-1/2 3/4 1.330 .500 10 24.8
1-1/2 5-1/2 10-3/8 9-1/2 1-1/4 1.915 .500 16 70.9
2 6-5/8 11-7/8 11-1/4 1-15/32 2.406 .625 24 91.6
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 11G

RP&C VALVES – CLASS 1500
EF556E
EF557E
SIZES 1/2” THRU 2”
NPT ENDS
SOCKET WELD ENDS
• FORGED STEEL GATE VALVE
• ASTM A105N LOW CARBON (.25 MAX.), NORMALIZED
• STANDARD PORT
• OS&Y – BOLTED BONNET
• WORKING PRESSURE (NON-SHOCK)
860 PSIG @ 900° F. Steam-Oil
1340 PSIG @ 850° F. Steam-Oil
3705 PSIG @ -20° To 100° F.
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 591 API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
E TRIM (13 Cr/FHF) STANDARD (See Page 8 for optional trims)
No. Part Material
ASTM
Spec.
Remarks
1 Handwheel Malleable Iron A47 Gr. 32510
2 Handwheel Nut Steel A108
3
Internal Tooth
Lockwasher
Steel
4 Nameplate Aluminum
5 Thrust Washer Stainless Steel Hardened
6 Operating Nut 416 Stainless Steel A582
7 Stem 410 Stainless Steel A276
8 Gland Nuts 303 Stainless Steel A194 Grade 8F
9 Gland Plate Forged Carbon Steel A105
10 Gland Carbon Steel B484 Gr. 2, Cl. C, Type 1
11 Eyebolt 410 Stainless Steel Hardened & Tempered
12 Eyebolt Washer Stainless Steel 300 Series
13a * Packing Graphite Grafoil® (241 or equal)
13b * Wiper Rings Braided Graphite 1630GF or equal
14 Bonnet Bolts Alloy Steel A193 Grade B7
15 Bonnet Forged Steel, Normalized A015N Low Carbon
16 * Gasket 316 SS/Grafoil® Spiral Wound
17 Seat Rings 410 Stainless Steel A276 Hard Faced
18 Wedge Cobalt-Chromium Super Alloy CoCr-A
19 Body Forged Steel, Normalized A105N Low Carbon
Operating Nut and Stem thread Lubricated
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size
Handwheel End To Center to
Socket Weld Socket Weld Approximate Typical Cv
Port
Dia. End Top(Open)
Bore
Depth
Weight Factors
1/2 4-1/2 4 8-1/4 1/2 .855 .375 7-1/4 6.9
3/4 4-1/2 4 8-1/4 1/2 1.065 .500 8-1/4 12.7
1 5-1/2 5-1/2 9 3/4 1.330 .500 13-1/4 31.6
1-1/2 6-5/8 6-1/2 10-5/8 1-3/16 1.915 .500 24-3/4 71.1
2 8-1/4 7 12-1/4 1-15/32 2.406 .625 39-1/2 112.9
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 3 V15

RP&C FORGED STEEL GATE VALVES
EF56D NPT ENDS SIZES ¼” THRU 2”
EF57D SOCKET WELD ENDS
• FORGED STEEL
• ASTM A105N LOW CARBON (.25 MAX.), NORMALIZED
• STANDARD PORT
• OS&Y – BOLTED BONNET
• WORKING PRESSURE (NON-SHOCK)
460 PSIG @ 900° F. Steam-Oil
715 PSIG @ 850° F. Steam-Oil
1975 PSIG @ -20° To 100° F.
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 591 API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
D TRIM (13 Cr/HF) STANDARD (See Page 8 for optional trims)
No. Part Material
ASTM
Spec.
Remarks
1 Handwheel Malleable Iron A47 Gr. 32510
2 Handwheel Nut Steel A108
3
Internal Tooth
Lockwasher
Steel
4 Nameplate Aluminum
5 Thrust Washer Stainless Steel Hardened
6 Operating Nut 416 Stainless Steel A582
7 Stem 410 Stainless Steel A276
8 Gland Nuts 303 Stainless Steel A194 Grade 8F
9 Gland Flange Carbon Steel A108 Grade 1018
10 Gland Carbon Steel B484 Gr. 1, Cl. C, Type 1
11 Eyebolt 410 Stainless Steel Hardened & Tempered
12 Eyebolt Washer Carbon Steel Grade 1018
13a * Packing Graphite Grafoil® (241 or equal)
13b * Wiper Rings Braided Graphite 1630GF or equal
14 Bonnet Bolts Alloy Steel A193 Grade B7
15 Bonnet Forged Steel, Normalized A015N Low Carbon
16 * Gasket 316 SS/Grafoil® Spiral Wound
17 Seat Rings 410 Stainless Steel A276 Hard Faced
18 Wedge CA-15 Stainless Steel A217 Heat Treated
19 Body Forged Steel, Normalized A105N Low Carbon
Operating Nut and Stem Thread Lubricated
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and production
runs, however parts will still conform to the requirements of API 602.
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size
Handwheel End To Center to
Socket Weld Socket Weld Approximate Typical Cv
Port
Dia. End Top(Open)
Bore
Depth
Weight Factors
1/4 4 3 6-1/4 9/32 .555 .375 4 2.3
3/8 4 3 6-1/4 25/64 .690 .375 4 5.7
1/2 4 3 6-1/4 25/64 .855 .375 4 5.1
3/4 4 3-1/2 6-1/2 1/2 1.065 .500 4-1/2 9.3
1 4-1/2 4-1/8 8-1/2 3/4 1.330 .500 6-1/2 24.8
1-1/4 5-1/2 4-3/4 9-1/2 1-3/16 1.675 .500 13 67.8
1-1/2 5-1/2 4-3/4 9-1/2 1-3/16 1.915 .500 13 70.9
2 6-5/8 5-1/4 11-1/4 1-15/32 2.406 .625 18 91.6
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 1G

RP&C FORGED STEEL GATE VALVES
EF158D CLASS 150 FLANGED
EF308D CLASS 300 FLANGED
EF608D CLASS 600 FLANGED
• SIZES ¼” THRU 2”
• FORGED STEEL
• ASTM A105N LOW CARBON (.25 MAX.), NORMALIZED
• STANDARD PORT
• OS&Y – BOLTED BONNET
• WORKING PRESSURE (NON-SHOCK)
CLASS 150
150 PSIG @ 576° F. Steam-Oil
285 PSIG @ -20° To 100° F.
CLASS 300
300 PSIG @ 839° F. Steam-Oil
740 PSIG @ -20° To 100° F.
CLASS 600
600 PSIG @ 576° F. Steam-Oil
1480 PSIG @ -20° To 100° F.
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 591 API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
D TRIM (13 Cr/HF) STANDARD (See Page 8 for optional trims)
No. Part Material
ASTM
Spec.
Remarks
1 Handwheel Malleable Iron A47 Gr. 32510
2 Handwheel Nut Steel A108
3
Internal Tooth
Lockwasher
Steel
4 Nameplate Aluminum
5 Thrust Washer Stainless Steel Hardened
6 Operating Nut 416 Stainless Steel A582
7 Stem 410 Stainless Steel A276
8 Gland Nuts 303 Stainless Steel A194 Grade 8F
9 Gland Flange Carbon Steel A108 Grade 1018
10 Gland Carbon Steel B484 Gr. 1, Cl. C, Type 1
11 Eyebolt 410 Stainless Steel Hardened & Tempered
12 Eyebolt Washer Carbon Steel Grade 1018
13a * Packing Graphite Grafoil® (241 or equal)
13b * Wiper Rings Braided Graphite 1630GF or equal
14 Bonnet Bolts Alloy Steel A193 Grade B7
15 Bonnet Forged Steel, Normalized A015N Low Carbon
16 * Gasket 316 SS/Grafoil® Spiral Wound
17 Seat Rings 410 Stainless Steel A276 Hard Faced
18 Wedge CA-15 Stainless Steel A217 Heat Treated
19 Body Forged Steel, Normalized A105N Low Carbon
Operating Nut and Stem thread Lubricated
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size
Handwheel End To End Center to
Port
Approximate Weight Typical Cv
Dia. 150 300 600 Top(Open)
150 300 600 Factors
1/2 4 4-1/4 5-1/2 6-1/2 6-1/4 25/64 6-3/4 7-1/2 8 5.1
3/4 4 4-5/8 6 7-1/2 6-1/2 1/2 7-1/2 10 11 9.3
1 4-1/2 5 6-1/2 8-1/2 8-1/2 3/4 11 12 13 24.8
1-1/2 5-1/2 6-1/2 7-1/2 9-1/2 9-1/2 1-3/16 19 23 27 67.8
2 6-5/8 7 8-1/2 11-1/2 11-1/4 1-15/32 29 36 39 70.9
3 8-3/8 8 11-1/8 14 13 2 50 63 68 91.6
DIMENSIONAL SPECIFICATIONS
NOTE: Class 150 Flanged valves feature integrally
forged flanges.
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 8G

RP&C FORGED STEEL GATE VALVES
EFWB46D MALE COUPLET X FEMALE SOCKET WELD
EFWB51D MALE X FEMALE NPT
EFWB52D MALE X FEMALE SOCKET WELD
EFWB53D MALE NPT X FEMALE SOCKET WELD
EFWB54D MALE SOCKET WELD X FEMALE NPT
EFWB55D MALE COUPLET X FEMALE NPT
• SIZES 1/2” THRU 1 1 / 2”
NOTE: 1/2” MALE THREADS ARE NOT COVERED BY API 602
• FORGED STEEL
• ASTM A105N LOW CARBON (.25 MAX.), NORMALIZED
• CONVENTIONAL PORT
• OS&Y – WELDED BONNET
• WORKING PRESSURE (NON-SHOCK)
460 PSIG @ 900° F. Steam-Oil
715 PSIG @ 850° F. Steam-Oil
1975 PSIG @ -20° To 100° F.
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 591 API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
D TRIM (13 Cr/HF) STANDARD (See Page 8 for optional trims)
No. Part Material
ASTM
Spec.
Remarks
1 Handwheel Malleable Iron A47 Gr. 32510
2 Handwheel Nut Steel A108
3
Internal Tooth
Lockwasher
Steel
4 Nameplate Aluminum
5 Thrust Washer Stainless Steel Hardened
6 Operating Nut 416 Stainless Steel A582
7 Stem 410 Stainless Steel A276
8 Gland Nuts 303 Stainless Steel A194 Grade 8F
9 Gland Flange Carbon Steel A108 Grade 1018
10 Gland Carbon Steel B484 Gr. 1, Cl. C, Type 1
11 Eyebolt 410 Stainless Steel Hardened & Tempered
12 Eyebolt Washer Carbon Steel Grade 1018
13a * Packing Graphite Grafoil® (241 or equal)
13b * Wiper Rings Braided Graphite 1630GF or equal
14 Bonnet Forged Steel, Normalized A015N Low Carbon
15 Seat Rings 410 Stainless Steel A276 Hard Faced
16 Wedge CA-15 Stainless Steel A217 Heat Treated
17 Body Forged Steel, Normalized A105N Low Carbon
Operating Nut and Stem thread Lubricated
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
MINIMUM QUANTITIES MAY BE REQUIRED
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size
Handwheel End To Center to
Socket Weld Socket Weld Approximate Typical Cv
Port
Dia. End Top(Open)
Bore
Depth
Weight Factors
1/2 4 5-9/16 6-1/4 25/64 .855 .375 4-1/2 5.1
3/4 4 6 6-1/2 1/2 1.065 .500 4-3/4 9.3
1 4-1/2 6-5/16 8-1/2 3/4 1.330 .500 6-3/4 24.8
1-1/2 5-1/2 7-7/16 9-1/2 1-1/4 1.915 .500 14 70.9
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 10G

RP&C FORGED STEEL GATE VALVES
EFWB48D MALE SOCKET WELD X FEMALE NPT
EFWB49D MALE X FEMALE SOCKET WELD
• INTEGRALLY REINFORCED MALE END
• SIZES 1/2” THRU 2”
• FORGED STEEL
• ASTM A105N LOW CARBON (.25 MAX.), NORMALIZED
• STANDARD PORT
• OS&Y – WELDED BONNET
• WORKING PRESSURE (NON-SHOCK)
460 PSIG @ 900° F. Steam-Oil
715 PSIG @ 850° F. Steam-Oil
1975 PSIG @ -20° To 100° F.
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 591 API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
D TRIM (13 Cr/HF) STANDARD (See Page 8 for optional trims)
No. Part Material
ASTM
Spec.
Remarks
1 Handwheel Malleable Iron A47 Gr. 32510
2 Handwheel Nut Steel A108
3
Internal Tooth
Lockwasher
Steel
4 Nameplate Aluminum
5 Thrust Washer Stainless Steel Hardened
6 Operating Nut 416 Stainless Steel A582
7 Stem 410 Stainless Steel A276
8 Gland Nuts 303 Stainless Steel A194 Grade 8F
9 Gland Flange Carbon Steel A108 Grade 1018
10 Gland Carbon Steel B484 Gr. 1, Cl. C, Type 1
11 Eyebolt 410 Stainless Steel Hardened & Tempered
12 Eyebolt Washer Carbon Steel Grade 1018
13a * Packing Graphite Grafoil® (241 or equal)
13b * Wiper Rings Braided Graphite 1630GF or equal
14 Bonnet Forged Steel, Normalized A015N Low Carbon
15 Seat Rings 410 Stainless Steel A276 Hard Faced
16 Wedge CA-15 Stainless Steel A217 Heat Treated
17 Body Forged Steel, Normalized A105N Low Carbon
Operating Nut and Stem thread Lubricated
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
MINIMUM QUANTITIES MAY BE REQUIRED
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size
Handwheel End To Center to
Socket Weld Socket Weld Approximate Typical Cv
Port
Dia. End Top(Open)
Bore
Depth
Weight Factors
1/2 4 7-5/8 6-1/4 25/64 .855 .375 5-1/2 5.1
3/4 4 8-11/16 6-1/2 1/2 1.065 .500 6-1/2 9.3
1 4-1/2 9-11/16 8-1/2 3/4 1.330 .500 10 24.8
1-1/2 5-1/2 10-3/8 9-1/2 1-1/4 1.915 .500 16 70.9
2 6-5/8 11-7/8 11-1/4 1-15/32 2.406 .625 24 91.6
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 12G

RP&C VALVES – CLASS 1500
EFWB556E NPT ENDS
EFWB557E SOCKET WELD ENDS
SIZES 1/2” THRU 2”
• FORGED STEEL GATE VALVE
• ASTM A105N LOW CARBON (.25 MAX.), NORMALIZED
• STANDARD PORT
• OS&Y – BOLTED BONNET
• WORKING PRESSURE (NON-SHOCK)
860 PSIG @ 900° F. Steam-Oil
1340 PSIG @ 850° F. Steam-Oil
3705 PSIG @ -20° To 100° F.
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 591 API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
E TRIM (13 Cr/FHF) STANDARD (See Page 8 for optional trims)
No. Part Material
ASTM
Spec.
Remarks
1 Handwheel Malleable Iron A47 Gr. 32510
2 Handwheel Nut Steel A108
3
Internal Tooth
Lockwasher
Steel
4 Nameplate Aluminum
5 Thrust Washer Stainless Steel Hardened
6 Operating Nut 416 Stainless Steel A582
7 Stem 410 Stainless Steel A276
8 Gland Nuts 303 Stainless Steel A194 Grade 8F
9 Gland Plate Forged Carbon Steel A105
10 Gland Carbon Steel B484 Gr. 2, Cl. C, Type 1
11 Eyebolt 410 Stainless Steel Hardened & Tempered
12 Eyebolt Washer Stainless Steel 300 Series
13a * Packing Graphite Grafoil® (241 or equal)
13b * Wiper Rings Braided Graphite 1630GF or equal
14 Bonnet Forged Steel, Normalized A015N Low Carbon
15 Seat Rings 410 Stainless Steel A276 Hard Faced
16 Wedge Cobalt-Chromium Super Alloy CoCr-A
17 Body Forged Steel, Normalized A105N Low Carbon
Operating Nut and Stem thread Lubricated
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size
Handwheel End To Center to
Socket Weld Socket Weld Approximate Typical Cv
Port
Dia. End Top(Open)
Bore
Depth
Weight Factors
1/2 4-1/2 4 8-1/4 1/2 .855 .375 7-1/4 6.9
3/4 4-1/2 4 8-1/4 1/2 1.065 .500 8-1/4 12.7
1 5-1/2 5-1/2 9 3/4 1.330 .500 13-1/4 31.6
1-1/2 6-5/8 6-1/2 10-5/8 1-3/16 1.915 .500 24-3/4 71.1
2 8-1/4 7 12-1/4 1-15/32 2.406 .625 39-1/2 112.9
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 4 V15

RP&C FORGED STEEL GATE VALVES
EFWB56D NPT ENDS SIZES ¼” THRU 2”
EFWB57D SOCKET WELD ENDS
• FORGED STEEL
• ASTM A105N LOW CARBON (.25 MAX.), NORMALIZED
• STANDARD PORT
• OS&Y – WELDED BONNET
• WORKING PRESSURE (NON-SHOCK)
460 PSIG @ 900° F. Steam-Oil
715 PSIG @ 850° F. Steam-Oil
1975 PSIG @ -20° To 100° F.
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 591 API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
D TRIM (13 Cr/HF) STANDARD (See Page 8 for optional trims)
No. Part Material
ASTM
Spec.
Remarks
1 Handwheel Malleable Iron A47 Gr. 32510
2 Handwheel Nut Steel A108
3
Internal Tooth
Lockwasher
Steel
4 Nameplate Aluminum
5 Thrust Washer Stainless Steel Hardened
6 Operating Nut 416 Stainless Steel A582
7 Stem 410 Stainless Steel A276
8 Gland Nuts 303 Stainless Steel A194 Grade 8F
9 Gland Flange Carbon Steel A108 Grade 1018
10 Gland Carbon Steel B484 Gr. 1, Cl. C, Type 1
11 Eyebolt 410 Stainless Steel Hardened & Tempered
12 Eyebolt Washer Carbon Steel Grade 1018
13a * Packing Graphite Grafoil® (241 or equal)
13b * Wiper Rings Braided Graphite 1630GF or equal
14 Bonnet Forged Steel, Normalized A015N Low Carbon
15 Seat Rings 410 Stainless Steel A276 Hard Faced
16 Wedge CA-15 Stainless Steel A217 Heat Treated
17 Body Forged Steel, Normalized A105N Low Carbon
Operating Nut and Stem thread Lubricated
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
Size
DIMENSIONAL SPECIFICATIONS
Handwheel
Dia.
End To
End
Center to
Top(Open)
Port
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Socket Weld
Bore
Socket Weld
Depth
Approximate
Weight
Typical Cv
Factors
1/4 4 3 6-1/4 9/32 .555 .375 4 2.3
3/8 4 3 6-1/4 25/64 .690 .375 4 5.7
1/2 4 3 6-1/4 25/64 .855 .375 4 5.1
3/4 4 3-1/2 6-1/2 1/2 1.065 .500 4-1/2 9.3
1 4-1/2 4-1/8 8-1/2 3/4 1.330 .500 6-1/2 24.8
1-1/4 5-1/2 4-3/4 9-1/2 1-3/16 1.675 .500 13 67.8
1-1/2 5-1/2 4-3/4 9-1/2 1-3/16 1.915 .500 13 70.9
2 6-5/8 5-1/4 11-1/4 1-15/32 2.406 .625 18 91.6
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 3G

RP&C FORGED STEEL GATE VALVES
EC56D NPT ENDS SIZES ¼” THRU 2”
EC57D SOCKET WELD ENDS
• ASTM A182 Gr. F5
• WORKING PRESSURE (NON-SHOCK)
600 PSIG @ 1615° F. Steam-Oil
800 PSIG @ 1355° F. Steam-Oil
2000 PSIG @ -20° To 100° F.
EK56D NPT ENDS SIZES ¼” THRU 2”
EK57D SOCKET WELD ENDS
• ASTM A182 Gr. F22 Cl. 3
• WORKING PRESSURE (NON-SHOCK)
600 PSIG @ 1615° F. Steam-Oil
800 PSIG @ 1355° F. Steam-Oil
2000 PSIG @ -20° To 100° F.
• STANDARD PORT
• OS&Y – BOLTED BONNET
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 591 API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
D TRIM (13 Cr/HF) STANDARD (See Page 8 for optional trims)
No. Part Material
ASTM
Spec.
Remarks
1 Handwheel Malleable Iron A47 Gr. 32510
2 Handwheel Nut Steel A108
3
Internal Tooth
Lockwasher
Steel
4 Nameplate Aluminum
5 Thrust Washer Stainless Steel Hardened
6 Operating Nut 416 Stainless Steel A582
7 Stem 410 Stainless Steel A276
8 Gland Nuts 303 Stainless Steel A194 Grade 8F
9 Gland Flange Carbon Steel A108 Grade 1018
10 Gland Carbon Steel B484 Gr. 1, Cl. C, Type 1
11 Eyebolt 410 Stainless Steel Hardened & Tempered
12 Eyebolt Washer Carbon Steel Grade 1018
13a * Packing Graphite Grafoil® (241 or equal)
13b * Wiper Rings Braided Graphite 1630GF or equal
14 Bonnet Bolts Alloy Steel A193 Grade B16
15 Bonnet Chrome Moly A182 Grade F5/F22
16 * Gasket 316 SS/Grafoil® Spiral Wound
17 Seat Rings 410 Stainless Steel A276 Hard Faced
18 Wedge CA-15 Stainless Steel A217 Heat Treated
19 Body Chrome Moly A182 Grade F5/F22
Operating Nut and Stem thread Lubricated
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
DIMENSIONAL SPECIFICATIONS
MINIMUM QUANTITIES MAY BE REQUIRED
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size
Handwheel End To Center to
Socket Weld Socket Weld Approximate Typical Cv
Port
Dia. End Top(Open)
Bore
Depth
Weight Factors
1/4 4 3 6-1/4 9/32 .555 .375 4 2.3
3/8 4 3 6-1/4 25/64 .690 .375 4 5.7
1/2 4 3 6-1/4 25/64 .855 .375 4 5.1
3/4 4 3-1/2 6-1/2 1/2 1.065 .500 4-1/2 9.3
1 4-1/2 4-1/8 8-1/2 3/4 1.330 .500 6-1/2 24.8
1-1/4 5-1/2 4-3/4 9-1/2 1-3/16 1.675 .500 13 67.8
1-1/2 5-1/2 4-3/4 9-1/2 1-3/16 1.915 .500 13 70.9
2 6-5/8 5-1/4 11-1/4 1-15/32 2.406 .625 18 91.6
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 5G

RP&C FORGED STEEL GATE VALVES
ELF56D NPT ENDS SIZES ¼” THRU 2”
ELF57D SOCKET WELD ENDS
• FORGED STEEL
• ASTM A350 Gr. LF2
• STANDARD PORT
• OS&Y – BOLTED BONNET
• WORKING PRESSURE (NON-SHOCK)
1100 PSIG @ 800° F. Steam-Oil
1975 PSIG @ -50° To 100° F.
800°F. IS MAX. OPERATING TEMP. FOR LF2
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 591 API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
D TRIM (13 Cr/HF) STANDARD (See Page 8 for optional trims)
No. Part Material
ASTM
Spec.
Remarks
1 Handwheel Malleable Iron A47 Gr. 32510
2 Handwheel Nut Steel A108
3
Internal Tooth
Lockwasher
Steel
4 Nameplate Aluminum
5 Thrust Washer Stainless Steel Hardened
6 Operating Nut 416 Stainless Steel A582
7 Stem 410 Stainless Steel A276
8 Gland Nuts 303 Stainless Steel A194 Grade 8F
9 Gland Flange Carbon Steel A108 Grade 1018
10 Gland Carbon Steel B484 Gr. 1, Cl. C, Type 1
11 Eyebolt 410 Stainless Steel Hardened & Tempered
12 Eyebolt Washer Carbon Steel Grade 1018
13a * Packing Graphite Grafoil® (241 or equal)
13b * Wiper Rings Braided Graphite 1630GF or equal
14 Bonnet Bolts Alloy Steel A193 Grade B8M Cl.2
15 Bonnet Forged Steel A350 Gr. LF2
16 * Gasket 316 SS/Grafoil® Spiral Wound
17 Seat Rings 410 Stainless Steel A276 Hard Faced
18 Wedge CA-15 Stainless Steel A217 Heat Treated
19 Body Forged Steel A350 Gr. LF2
Operating Nut and Stem thread Lubricated
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
MINIMUM QUANTITIES MAY BE REQUIRED
DIMENSIONAL SPECIFICATIONS
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Size
Handwheel End To Center to
Socket Weld Socket Weld Approximate Typical Cv
Port
Dia. End Top(Open)
Bore
Depth
Weight Factors
¼ 4 3 6-1/4 9/32 .555 .375 4 2.3
3/8 4 3 6-1/4 25/64 .690 .375 4 5.7
1/2 4 3 6-1/4 25/64 .855 .375 4 5.1
3/4 4 3-1/2 6-1/2 1/2 1.065 .500 4-1/2 9.3
1 4-1/2 4-1/8 8-1/2 3/4 1.330 .500 6-1/2 24.8
1-1/4 5-1/2 4-3/4 9-1/2 1-3/16 1.675 .500 13 67.8
1-1/2 5-1/2 4-3/4 9-1/2 1-3/16 1.915 .500 13 70.9
2 6-5/8 5-1/4 11-1/4 1-15/32 2.406 .625 18 91.6
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 4G

RP&C FORGED STEEL GATE VALVES
ES56A NPT ENDS SIZES ¼” THRU 2”
ES57A SOCKET WELD ENDS
• STAINLESS STEEL
• ASTM A182 Gr. F316/F316L
• STANDARD PORT
• OS&Y – BOLTED BONNET
• WORKING PRESSURE (NON-SHOCK)
600 PSIG @ 1200° F. Steam-Oil
800 PSIG @ 1130° F. Steam-Oil
1920 PSIG @ -20° To 100° F.
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 591 API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
A TRIM (316 SST) STANDARD (See Page 8 for optional trims)
No. Part Material
ASTM
Spec.
Remarks
1 Handwheel Malleable Iron A47 Gr. 32510
2 Handwheel Nut Steel A108
3
Internal Tooth
Lockwasher
Steel
4 Nameplate Aluminum
5 Thrust Washer Stainless Steel Hardened
6 Operating Nut 416 Stainless Steel A582
7 Stem 316 Stainless Steel A276
8 Gland Nuts 303 Stainless Steel A194 Grade 8F
9 Gland Flange 316 Stainless Steel A240 Grade 1018
10 Gland 316 Stainless Steel B525 Gr. 2, Type 1
11 Eyebolt 316 Stainless Steel
12 Eyebolt Washer Carbon Steel Grade 1018
13a * Packing Graphite Grafoil® (241 or equal)
13b * Wiper Rings Braided Graphite 1630GF or equal
14 Bonnet Bolts Alloy Steel A193 Grade B8M Cl. 2
15 Bonnet Forged Stainless Steel A182 Gr. F316/F316L
16 * Gasket 316 SS/Grafoil® Spiral Wound
17 Seat Rings 316 Stainless Steel A276 Hard Faced
18 Wedge 316 Stainless Steel A351 Grade CF8M
19 Body Forged Stainless Steel A182 Gr. F316/F316L
Operating Nut and Stem thread Lubricated
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
Size
DIMENSIONAL SPECIFICATIONS
Handwheel
Dia.
End To
End
Center to
Top(Open)
Port
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Socket Weld
Bore
Socket Weld
Depth
Approximate
Weight
Typical Cv
Factors
1/4 4 3 6-1/4 9/32 .555 .375 4 2.3
3/8 4 3 6-1/4 25/64 .690 .375 4 5.7
1/2 4 3 6-1/4 25/64 .855 .375 4 5.1
3/4 4 3-1/2 6-1/2 1/2 1.065 .500 4-1/2 9.3
1 4-1/2 4-1/8 8-1/2 3/4 1.330 .500 6-1/2 24.8
1-1/4 5-1/2 4-3/4 9-1/2 1-3/16 1.675 .500 13 67.8
1-1/2 5-1/2 4-3/4 9-1/2 1-3/16 1.915 .500 13 70.9
2 6-5/8 5-1/4 11-1/4 1-15/32 2.406 .625 18 91.6
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 6G

RP&C FORGED STEEL GATE VALVES
ESWB56A NPT ENDS SIZES ¼” THRU 2”
ESWB57A SOCKET WELD ENDS
• STAINLESS STEEL
• ASTM A182 Gr. F316/F316L
• STANDARD PORT
• OS&Y – WELDED BONNET
• WORKING PRESSURE (NON-SHOCK)
600 PSIG @ 1200° F. Steam-Oil
800 PSIG @ 1130° F. Steam-Oil
1920 PSIG @ -20° To 100° F.
• CONFORM TO THE APPLICABLE PARTS OF THE
FOLLOWING SPECIFICATIONS:
API
API 591 API 598 API 602
ASME/ANSI
B1.20.1 B16.11 B16.34 B31.1 B31.3
NOTE: Valve can be furnished to meet NACE SPEC. MR0175.
• MATERIALS OF CONSTRUCTION
A TRIM (316 SST) STANDARD (See Page 8 for optional trims)
No. Part Material
ASTM
Spec.
Remarks
1 Handwheel Malleable Iron A47 Gr. 32510
2 Handwheel Nut Steel A108
3
Internal Tooth
Lockwasher
Steel
4 Nameplate Aluminum
5 Thrust Washer Stainless Steel Hardened
6 Operating Nut 416 Stainless Steel A582
7 Stem 316 Stainless Steel A276
8 Gland Nuts 303 Stainless Steel A194 Grade 8F
9 Gland Flange 316 Stainless Steel A240 Grade 1018
10 Gland 316 Stainless Steel B525 Gr. 2, Type 1
11 Eyebolt 316 Stainless Steel
12 Eyebolt Washer Carbon Steel Grade 1018
13a * Packing Graphite Grafoil® (241 or equal)
13b * Wiper Rings Braided Graphite 1630GF or equal
14 Bonnet Forged Stainless Steel A182 Gr. F316/F316L
15 Seat Rings 316 Stainless Steel A276 Hard Faced
16 Wedge 316 Stainless Steel A351 Grade CF8M
17 Body Forged Stainless Steel A182 Gr. F316/F316L
Operating Nut and Stem thread Lubricated
* Recommended Spare Parts
Note: Materials of construction may vary due to availability and Production
runs, however parts will still conform to the requirements of API 602.
Size
DIMENSIONAL SPECIFICATIONS
Handwheel
Dia.
End To
End
Center to
Top(Open)
Port
NOTE: Dimensions shown are subject to change. Contact factory
for certified prints (exact dimensions) when required.
Socket Weld
Bore
Socket Weld
Depth
Approximate
Weight
Typical Cv
Factors
1/4 4 3 6-1/4 9/32 .555 .375 4 2.3
3/8 4 3 6-1/4 25/64 .690 .375 4 5.7
1/2 4 3 6-1/4 25/64 .855 .375 4 5.1
3/4 4 3-1/2 6-1/2 1/2 1.065 .500 4-1/2 9.3
1 4-1/2 4-1/8 8-1/2 3/4 1.330 .500 6-1/2 24.8
1-1/4 5-1/2 4-3/4 9-1/2 1-3/16 1.675 .500 13 67.8
1-1/2 5-1/2 4-3/4 9-1/2 1-3/16 1.915 .500 13 70.9
2 6-5/8 5-1/4 11-1/4 1-15/32 2.406 .625 18 91.6
RP&C VALVE
A Division of Conbraco Industries, Inc.
RPBI9000-99
Hwy. 501 East
Conway, SC 29526
843/347-4666 (PHONE)
843/347-1773 (FAX)
Page 7G