DG-600E Stand-alone Proximity Reader - GEM,Gianni Industries, Inc.

DG-600EStand-alone Proximity ReaderFeaturesAllow up to 600 proximity cards and PIN codesRF Frequency: EM-400x 125 KHzTamper switch and alarm buzzer includedFully Programmable via keypad and master codeAccess mode selectable: card only, card or PIN, card+PINSupport Wiegand 26 or 44-bit format auxiliary readerLogical memory to prevent duplicationInvalid PIN Lock-outBeeper soundNon-Volatile MemoryRemovable memory chip from the PC boardStatementDG-600E stand-alone Proximity Reader is ideal forsingle-door access control. It may connect to another readerand serve as a controller. DG-600E enables the beeper to gooff whenever the keypad is pressed. A tamper switch is used toprotect the reader from external damage by linking the relay tothe alarming system. This model communicates in Wiegandprotocol and has a set of 600 proximity cards set to 26-bitor44-bit. It takes the reader 0.5 seconds at most to read aproximity card or 5-digit PIN code. The built-in non-volatilememory preserves the PINs for as long as 10 years. Evenwhen the power fails, the stored PIN codes will not be washedaway.GEM GEM GEMGEM GEM GEM GEM GEMWarrantyThe product is warranted against defects in material andworkmanship while used in normal service for a period of 1year from the date of sale to the original customer. The GEMpolicy is one of continual development and improvement;therefore GEM reserves the right to change specificationswithout notice.SpecificationsUnit: mmGEM GEM GEMGEM GEM GEM GEM GEMCopyright © Gianni Industries, Inc. All rights reserved.DM-CA-DG-600E Ver. E Published on 2010.12.2035.51 2 34 5 67 8 9*0#70127.5Operating Voltage: 12VDCCurrent Draw: Average 50mA, Peak 100mA/12VDCTransmitting Frequency: 125 KHzMemory Volume: 600 Proximity cards/tokens and PIN codesRead Range: Up to 10 cm (Depending on local installationconditions)Keyboard: 12 digit keypad (0~9, *, #)Input: Request-to-exit, door reed switch, auxiliary readerRelay rating: 2A MAX/30VDC, 0.4A/120VACInvalid PIN Lock-out: The system will shut down for 60seconds after the attempt to read the master or PIN cardshas faiiled for over 5 times. (No beeper signal when pressingon the keypad)Relocking timer:Strike Time: 1~99 seconds (adjustable)Strike mode: Access Timer or LatchAlarm Function:Door Held Open Alarm: 10~99Door Forced AlarmPanel Temper AlarmAuxiliary Reader Format: Wiegand 44 or 26-bit only format(adjustable), hexadecimal (Em 64-bit standard R/O orcompatible)Case Material: ABS (UL94V0)Color: Beige WhiteOperating Temperature: -20~+70°CA m b i e n t H u m i d i t y : 5 ~ 9 5 % r e l a t i v e h u m i d i t y ( n o n -condensing)Visual Signals: 3 LED display with audible Indication(Red/Yellow/Green)EMC: Meet CE requirementGIANNI INDUSTRIES, INC.No.13, Zhongxing Rd., Tucheng Dist.,New Taipei City 23678, Taiwan (R.O.C.)Tel: +886-2-2267-7986 / Fax: +886-2-2267-9876E-mail: inquiry1@gianni.com.twWebsite: www.gianni.com.tw

DG-600EStand-alone Proximity ReaderOptional Readers714-60Mifare ® ID ReaderGEMPROX-EEM 125KHzGEMPROX-26MMifare ® ID ReaderGEMPROX-630EM-KPEM 125KHz Keypad andproximity readerGEMPROX-630EMEM 125KHzConnecting DiagramFail-Safe LockSt 2 connect to 1-2Fail-Secure LockSt 2 connect to 2-3Door switch contact or the outputof electric lock signalPush ButtonPower supply(12VDC)*Linear supply recommendedExternal relay connectingto the warning systemAuxiliary Reader(Wiegand Format)Insert 2-3 position to resetDG-600E Jp1 leads to Wiegand 44 bits formatDG-600E Jp1 short-circuit to Wiegand 26 bits formatConnect 1-2,C and D contact is N.C.Connect 2-3, for N.O.Connect to 1-2;C and A contact is N.C.Connect to 2-3; for N.O.Copyright © Gianni Industries, Inc. All rights reserved.DM-CA-DG-600E Ver. E Published on 2010.12.20GIANNI INDUSTRIES, INC.No. 13, Zhongxing Rd., Tucheng Dist., New Taipei City 236,Taiwan (R.O.C.)Tel: 886-2 2267 7986 / Fax: 886-2 2267 9876E-Mail: info@gianni.com.twWebsite: gianni.tw