EVIL omen manual 2 - Paintball Solutions

More documents

Recommendations

Info

Omen Manual 2.0 6/21/05 9:56 AM Page 22O M E N 2.0 EVIL DETONATOR DIAG RA MO M E N 2.0 BOARD PROGRA M M I N GOMEN 2.0 Board Programming01 Detonator End Cap 5720102 Detonator Adjusting Ring 5720203 Inner Tube 5720304 Regulator Seat 5720405 Thrust Element 5720506 Seal Retainer 5720607 Detonator Main Body 5720708 Piston Spring 5720809 Piston 57209OMEN 2.0 Parts Kit (18102)10 Snap Ring 5721011 Locking Screw 10/32 Oval Point 5721112 O-Ring 011/70 Buna 5721213 O-Ring 008/90 Urethane (Poppet O-ring)4092314 Retaining Screw 8/32 Dog Point 5721315 O-Ring 012/90 Urethane 4091916 10/32 Black Lower Locking Scre w 4131817. Detonator Regulator 572001/8” Hex Key 420263/32” Hex Key 420331/16” Hex Key 42036Omen Hammer Cushion 57712O-ring 15/70 Urethane 57738O-ring 19/70 Buna 57728BALLS/SECPULL TRIGGER ANDHOLDTURN POWER ON WITH TRIGGER PULLED ANDHELD INWAIT FOR LED TO COME ON(ABOUT 2 SECONDS)RELEASE TRIGGERElectronic Trigger SensitivityPULL THEN RELEASE, PULL AGAIN ANDHOLDWAIT FOR LIGHT TO TURN OFF THEN RELEASE TRIGGER5 TO 25 BALLS PER SECOND 1 TO 50 POINTSWHILE COUNTING CLICK THE TRIGGER AND HOLD IT IN ON THE DESIREDSETTING UNTIL THE LED GOES OFF. RELEASE THE TRIGGER AND ONCE THE LED IS ONSTEADY, THE VALUE HAS BEEN SAVED AND IT’S READY TO FIRE.actual size2223
Omen Manual 2.0 6/21/05 9:56 AM Page 24O M E N 2.0 BOARD PROGRA M M I N GPROGRAMMING EXAMPLESTo set rate of fire to 20bps:Start with the power turned off, hold in trigger and turn power on. Wait for about 2 secondsand LED will come on, release trigger and then pull it once more and hold until the LED turnsoff, this selects the Ball/Second register. Starting at five, click the trigger while counting and holdthe trigger in on the 20th count. Hold until the LED goes out, meaning the value has beenaccepted, and then release the trigger once again. It will then reboot with the new valueindicated by a single flash and it will then be live and ready to fire.Setting Electronic Trigger Sensitivity to 5 pointsStart with the power turned off, hold in trigger and turn power on. Wait for about 2 secondsand LED will come on, release trigger and then pull it once and release, then pull a second timeand hold until the LED turns off, this selects the de-bounce register. Starting at one, click thetrigger while counting and hold the trigger in on the 5th click. Hold until the LED goes outmeaning the value has been accepted and then release the trigger once again.It will then reboot with the new value indicated by a single flash and it will then be live andready to fire.NOTE: If at any point a mistake is made just turn power off and start again. Theselected values are stored in permanent memory and will remain set even withouta battery connected.WHEN SETTING BALLS/SECOND ALWAYS START COUNTING AT FIVE BECAUSE FIVE IS THELOWEST SETTING. WHEN SETTING THE ELECTRONIC TRIGGER SENSITIVITY ALWAYS STARTCOUNTING AT ONE. ALL PROGRAMMING IS DONE USING THE LED ON THE RIGHT SIDE OFTHE EVIL OMEN TRIGGER FRAME.charging EVIL O M E N 2.0The OMEN battery is a 9 volt rechargeable battery. The battery needs a full 22 hours to chargebefore it is full. The battery does not come fully charged. For best long term battery life, EVILrecommends you charge your OMEN frame for a full 22 hours before using it. You can useregular 9 volt batteries with this frame if your rechargeable battery is dead or you want to playwith the frame right away. A blinking on/off indicator light means your OMEN frame needs tobe charged right away.Charge PortTURN MARKER OFF TO CHARGEMaintaining EVIL OMEN 2.0The trigger frame handlemight get warm duringcharging.Loss of rear gripframescrew (59) can cause searnot to drop and imitate adead battery.The EVIL OMEN is easy to strip for cleaning and basic maintenance. Regular cleaning andmaintenance is highly recommended, including frequent checks of all air systemcomponents. Keep screws tightened. Replace worn components with factory parts; allleaks must be repaired promptly. Air system repairs are best performed by the factory oran authorized factory repair facility; contact PMI for information regarding authorized repairfacilities: 1.800.579.1633.WARNINGDO NOT ATTEMPT TO PERFORM MAINTENANCE PROCEDURES UNLESS QUALIFIEDTO DO SO. DO NOT DISASSEMBLE MARKER UNTIL IT IS COMPLETELY DRAINEDOF COMPRESSED GAS OR AIR AND ALL PAINTBALLS HAVE BEEN REMOVED. ALLFILLING OF COMPRESSED GAS OR AIR CYLINDERS MUST BE DONE BY QUALIFIEDPERSONS.CONTACT PMI, INC., FOR REPAIR ASSISTANCE AND INFORMATION REGARDINGAUTHORIZED REPAIR FACILITIES. PHONE 800.579.1633; WWW. BUYPMI.COMPAINTBALL MARKER AIR SYSTEMS MUST BE REPAIRED OR REPLACED ONLY WITHTHE CORRECT PRESSURE RATED COMPONENTS.2425
Page 1 and 2: Omen Manual 2.0 6/21/05 9:56 AM Pag
Page 3: Omen Manual 2.0 6/21/05 9:56 AM Pag

EVIL omen manual 2 - Paintball Solutions

Create successful ePaper yourself

Delete template?

Save as template?