CE 311 Piezoelectric Accelerometer Type CE 311 - Istec International

More documents

Recommendations

Info

Piezoelectric AccelerometerCE 311.DESCRIPTIONThe CE 311 accelerometer is equipped with asymmetrical shear mode polycrystalline measuringelement with internal housing insulation. Integralelectronics provides charge-to-current conversionand eliminates the need for a charge amplifier. Themodulated current output signal allows the use of 2-wire cable for trouble free transmission over longdistances.The CE 311 accelerometer is fitted with an integralcable protected by a stainless steel flexible tubewelded to the housing. The system is fully protectedagainst cooling fluids, lubricants, water, steam etc.SPECIFICATIONSInput power requirementsSignal transmissionSignal processing: 12...28 V DC , zero signal current 3...8 mA: 2-wire system with modulated current output: Galvanic separation unit or mounting electronicsOPERATINGSensitivity (at +23°C ±5°C) : 50 μA/g ±5%Dynamic measuring range (random): 0.004 g to 40 g peakOverload capacity (spikes): Up to 100 g peakTransverse sensitivity : ≤ 3% (when measured at 15 Hz and 5 g)Linearity: ≤ 1% over dynamic measuring rangeResonant frequency (mounted): 20 kHz nominalFrequency response : ±5% between 2 Hz and 5 kHz: ±10% between 5 kHz and 8 kHzTemperature error: ±5% for temperature range -55°C to +23°C: ±2% for temperature range +23°C to +125°CReview copyENVIRONMENTALTemperature rangeShock accelerationExplosive atmosphere• EC type examination certificate: -55°C to +125°C maximum, survival (for maximum of 15 min) to +150°C: 500 g peak (half sine 1 ms): Available in Ex i version for use in hazardous locations according to:: KEMA 04 ATEX 1055 II 1 G (Zones 0, 1, 2) EEx ia IIC T4 to T6For specific parameters of the mode of protection concerned and special conditions for safe use, please refer to the “EC typeexamination certificate” that is available from Vibro-Meter SA on demand.• cCSAus standardCorrosion, humidityBase strain sensitivity: Certificate No. 1514310, Class I, Div. 1, Groups A, B, C and D, Ex ia: Stainless austenitic steel, hermetically welded: 0.0015 g/μεMOUNTING4 Allen screws M6 x 35, DIN 912, steel 12.9, 4 spring washers M6, DIN 7980, spring steel. Fastening torque 15 Nm.CALIBRATIONDynamic calibration at factory at 5 g peak and 120 Hz (+23°C). No subsequent calibration necessary.© Vibro-Meter SA / 262-052 / 08.06 / E 2 / 4
Piezoelectric AccelerometerCE 311ACCESSORIESCG 310 Connector GSI 122 / GSI 130 Galvanic separation unitJB 105 / JB 116 Junction box K 209 / K 213 Transmission cableMECHANICAL DRAWINGMarker sleeve (colour blue) toindicate intrinsically safeDirection of acceleration toprovide a positive signalA40±130±0.234.8±16.5±0.222±1BMARKING∅28±1Review copyMARKING11±0.5∅8.7 nom.Flexible, leaktightprotection tubeMinimum bending radius: 50 mmClipping points of the cable should beno more than 100 to 200 mm apartMARKINGAdapter for junction box typeJB 105 / JB 116 or modifiedconnector type MS3106E14S7PCable K213Clip, DIN 6799Ra 0.80.01 Mounting surface50±10 33±1Length L, see ordering information 70±10030±0.240±1 25 max.View A∅11±0.1WIRING DIAGRAMView B∅11±0.1500 +1005±1AccelerometerProtection tubeAdaptor© Vibro-Meter SA / 262-052 / 08.06 / E 3 / 4
Page 1: CE 311Piezoelectric AccelerometerTy

CE 311 Piezoelectric Accelerometer Type CE 311 - Istec International

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?