TELEPERM® XS System Overview - AREVA NP Inc.

More documents

Recommendations

Info

Hard- and SoftwareComputer and communication componentsSVE2Processing module for operation on TXS backplane bus Processor:AMD K6-2E Frequency:266 MHzSL22Communication module as piggyback module forprocessing module, for 12 MBit/s TXS Profibus networks(successor type to SL21) Bus interfaces: 2 Combinable:Up to 4 SL22/SVE2SLM2Electrical/optical converter for 12 MBit/sTXS Profibus networks (successor type to SLLM) Electrical connections: 1 Optical connections: 2SCP3Communication processor for 10 MBit/s TXS Ethernetfor operation on TXS backplane bus(successor type to SCP1, SCP2) Electrical connections: 1SES1Switch and media converter for 10/100 MBit/sTXS Ethernet networks Electrical connections: 3 Optical connections: 2SEPC2TXS embedded PC, e.g. for implementation of gateways,for installation in TXS cabinets Ethernet-ports: 3 Profibus-ports: 2 Other ports:DVI, VGA, USB, PS2,serial, parallelInput /output modulesSAI1Analog input module (successor type to S466) Channels:16 (single-ended input)or 8 (differential) Voltage measuring: 0…125 mV; 0…1.25 V; Ranges: 0…2.5 V; 0…5 V; 0…10 V;1…5 V; -125…125 mV;-1.25…1.25 V; -2.5…2.5;-5…5 V; -10…10V Current measuringranges:20 mA; 50 mA Compatibility mode: with S466SAO1Analog output module (successor type to S470 Channels: 8 Voltage outputs: -10…10 V/3 mA Current outputs: 20 mA/750 Ω; 50 mA/300 Ω Compatibility mode: with S470SDI1 und SDI2Binary input module (successor types to S430, S431) Channels: 32 Signals:24 V/7 mA (SDI1-24)24 V/0.7 mA (SDI2-24)48 V/3.5 mA (SDI1-48) Compatibility mode: with S430/S431SDO1Binary output module (successor type to S451) Channels: 32 Signals:24 V/250 mA max (SDO1-24)48 V/125 mA max (SDO1-48) Compatibility mode: with S451SGPIO1Multi-purpose module with counter, analog and binaryinputs and outputs Counter: Analog inputs: Binary inputs*: Analog outputs*: Binary outputs*:4 × RS422, 10 MHz or4 × TTL, 10 MHz or4 × 24 V, to 25 kHz4 × 0…10 V4 x 24 V4 x -10…10 V/3 mA4 x 24 V* in preparation46
Signal conditioningSAA1Analog signal conditioning module with voltage supplyfor transducers, low-pass filter, test sockets and overvoltageprotection Channels: 2 Transducers:20 mA, 2- and 4-wire circuitry Voltage output: 0…2.5 V Current output: 20 mA Overvoltage:230 V (inputs)SNV1-2,5, SNV1-10Standard signal multiplier, for analog signal distribution.Includes galvanic isolation and overvoltage protection Input:0…2.5 V, 0…10 V, 0(4)…20 mA Output:4 × 0(4)…20 mA Overvoltage:230 V AC/DC (outputs)STT1Temperature transducer RTDs: Thermocouples: Combination sensors: Output: Reference pointcompensation:Ptxxx, Nixxx in2/3/4-wire circuitryK, J, B, E, N, R, S, T etc.RTD and thermocouple0…10 V or 4…20 mAinternal or externalSBC1Binary signal conditioning module with contact power supply,open-circuit monitoring, non-coincidence monitoringof changeover contacts, simulation inputs4 channels each with: Connect power supply: 48 V or 24 V Inputs:1 changeover contact or2 single contacts or2 electronic contactsSCR1Module for the inductive position measurement of controlrods in pressurized water reactors, with synchronization logic Exciter outputs: 2 × 0…200 mA/31 Hz AC inputs:2 × 4, 0…22 V/100 Hz Voltage outputs: 2 × 4, 0…10 VNeutron flux instrumentation modulesSCV1PDC amplifier, signal conditioning for neutron flux detectorssuch as ionization chambers or cobalt self-powered neutrondetectors Channels: 3 Input:0…3 × 10 -6 to 0…1 × 10 -2 A Output:0…10 VSCV1BDC amplifier similar to SCV1P, but with integrated floatinghigh-voltage supply, e.g. for fission chambers High voltage:200 VSCV2DC amplifier, signal conditioning for neutron flux detectors.Automatic measuring range changeover. Additional isolatedoutput for connection to backup or ATWS systems Channels: 1 Input:0…10 -12 to 0…10 -3 A Output:0…10 VSPSR1Preamplifier, signal conditioning for pulse detectors Channels: 2 Pulse rate:1 MHzSSR1Pulse amplifier and discriminator, for source rangemeasurements and activity monitoring. An audio channelcan be connected Channels: 2 Pulse rate:1 MHz Pulse interval:>150 ns Frequency dividerfor output: 1:1, 1:5 Output:RS422, TTLSPWR1Preamplifier for fission chambers Channels: 1 Pulse rate:1 MHz AC:5 μASSC1Signal conditioning for active and passive sensors,with stand-still/speed monitoring Frequency/speed: 0…30 MHz / 0…6000 U/min Sensor power supply: 20…30 V, 100 mA Analog output: 0…10 V / 4…20 mA Pulse output:0/24 V and RS42247
Page 3: Qualification 30 Qualification Conc
Page 6 and 7: I&C solutions based on TELEPERM ®
Page 8 and 9: I&C solutions based on TELEPERM ®
Page 10: I&C solutions based on TELEPERM ®
Page 14 and 15: System design and mode of operation
Page 20 and 21: Engineering, testing and documentat
Page 26 and 27: Safety features and architecturesAr
Page 28 and 29: Safety features and architecturesDe
Page 30 and 31: QualificationThe TELEPERM ® XS sys
Page 34 and 35: QualificationTwo-stage licensingfor
Page 36 and 37: OperationVirtually no maintenanceTE
Page 38 and 39: OperationTroubleshootingFault annun
Page 40 and 41: OperationUser interfacesof the serv
Page 42 and 43: Long-term support for TELEPERM ® X
Page 44 and 45: Long-term support for TELEPERM ® X
Page 48 and 49: Hard- and SoftwareNeutron flux inst
Page 50: System dataThe components of TELEPE

TELEPERM® XS System Overview - AREVA NP Inc.

Create successful ePaper yourself

Delete template?

Save as template?