PRG Series 400™ 400 Amp Disconnect One Source. Unlimited ...

Series 400 400 Amp Disconnect Specifications
The PRG Series 400 400 Amp Disconnect shall be mounted in a Rolling Rack with two removable
covers exposing the connector and control panels of the unit. Two locking casters shall keep the
unit in place when connected.
Solid copper bus bars shall be used in all high - current circuitry, reducing losses and internal heating.
Two thermostatically controlled cooling fans shall be mounted within the enclosure and shall turn on
when internal bus bar temperatures reach 55°C. Replaceable metal air filters shall cover fan inlets.
Six Cam-Lok Series E1016 high current connections shall be provided for input power. Double
Neutral connectors shall handle excessive neutral currents generated by low power factor loads.
Neon lamps shall indicate when the cable feeding the Disconnect is energized. Twelve Cam-Lok
Series E1016 high-current connectors shall be provided for output power. Safety covers shall be
provided for all outputs.
A thermal-magnetic Main Breaker shall protect circuit wiring so that long term operation at currents
in excess of rated will cause it to trip, while magnetic elements respond quickly to overloads resulting
from fault current surges. The Main Breaker shall tolerate momentary overcurrent conditions caused
by inrush currents to prevent nuisance tripping when such loads are energized with full line voltage.
The inrush limit shall be adjustable from 2000 to 4000 Amps by a slider control.
A green LED Pilot Light shall indicate when the Main Breaker is ON. Operation of the LED may be
checked when the Main Breaker is OFF by pushing in on the lens cap causing the LED to light. Seven
digital LED meters shall monitor the power flowing through the Disconnect. Three voltmeters shall
measure phase voltages present at the input to the Main Breaker. A rocker switch shall allow connection
of the meters between the three phases (Ø-Ø) or between each phase and neutral (Ø-N).
Four current meters shall measure the current flowing in each phase and in the neutral circuit. The
current meters shall be isolated from the AC line by current transformers. The meters shall display
a full-wave averaging, RMS calibrated value.
Five color coded, insulated test points shall be provided for metering the output voltages after the
Main Breaker. Local convenience outlets shall provide protected branch circuits: One 120V, 15 Amp
single phase circuit serving two Edison outlets; One 208V, 15 Amp single phase circuit serving two
Neutrik® PowerCon® outlets; One 208V, 20 Amp single phase circuit serving one NEMA L6-20R
outlet; and one 120V/208V, 30 Amp 3-phase, 5-wire circuit serving two NEMA L21-30R outlets.
The Series 400 Disconnect shall be approved for use in the U.S. and Canada, or in any locality with
a 5-wire, 120/208V power grid. The unit is also suitable for use with portable power sources (generators)
as long as its ratings are not exceeded and an adequate Earth ground has been established.
The unit shall conform to UL Standard 1640, be certified to Canadian Standard CAN/CSA STD C22.2
No. 29, and shall carry the Intertek ETL safety mark. The unit shall be used in dry locations only and
may be operated with the front rack cover in place, if desired.
Ordering Information
20.9680.0200 Series 400 400 Amp Disconnect
XØ VOLTS YØ VOLTS ZØ VOLTS
MAIN
BR EAKER
ON
PUSH
TO
TES T
SWITCH TO OFF
POSITION TO
RESET BREAKER
INPUT VOLTAGES
400 AMP
MAIN BREAKER
ON
Type 1Enclosure
For use in DryLocations
50 C MaxAmbient
For Use in Areas Not Readily Accessible bythe General Public
FOR USE BY QUALIFIED PERSONNEL ONLY
WARNING - Risk of ElectricShock.
OFF
2000A 3000A 4000A
INRUSH LIMIT
SETTING
ARC MIXE D T U NGSTEN
L OADS LOADS L OADS
Conforms to:
ProductionResourceGroup
UL STD 1640
8617AmbassadorRow
Suite 120
Certified to:
Dallas, TX 75247
CAN/CSASTDC22.2
Made inUSA
No.29
XXXXX
S-400
400 AMP DISCONNECT
MODEL 23-9680-0200
Ø -Ø
Ø -N
600A MAX
NEUT AMPS
120/208V
3ØY/30 A
Production Resource Group
XØ AMPS
XØ
GROUND
FOR BRANCH CIRCUIT USE ONLY
120V / 15A 208V / 15A 208V / 20A
120/208V
3ØY/30 A
400A MAX
YØ AMPS
YØ
NEUTRAL
120/208V
3ØY/30 A
ZØ AMPS
ZØ
OUTPUT
VOLTAGES
TEST POINT
FUSES
1A / 250V
AGC1
RATINGS and AMPACITY
Voltage Rating: 120/208V 3-phase wye with Neutral and
Ground
Line Frequency: 50 - 60 Hz
Current Rating, Phases: 400 Amps per phase continuous
Current Rating, Neutral: 600 Amps continuous
Current Rating, Ground: 400 Amps
Fault Current Interrupting Capacity: 42,000 Amps
Fault Current Interrupt Time: Circuit clears in less than
one line cycle
MAIN BREAKER
Type: Thermal-Magnetic, Square D Model LAL36400
Number of Poles: 3
Voltage Rating: 600V AC
Current Rating: 400 Amps
Inrush Overload Limit: Adjustable from 2000A to 4000A
DIGITAL LED METERS (7)
Update Rate: 2.5 samples/sec.
Display: 3-digit reading
INPUT VOLTMETERS (3)
Accuracy: ± 1 Volt
Input Range: 85 - 264 Volts AC
Overload Protection: 300V AC
OUTPUT AMMETERS (4)
Phase Current Meters full scale reading: 400 Amps
Neutral Current Meter full scale reading: 600 Amps
Overcurrent Rating: 1.5X rated full scale reading
Accuracy (sine wave): ±0.15% of full scale or ±6 counts
ENVIRONMENTAL
Operational Temperature Range: -20° C to +50° C
Cooling: Two thermostatically controlled fans
For Dry Locations Only
DIMENSIONS and WEIGHT
Unit in Rolling Rack: 22.5”(L) x 22.5”(W) x 30.5”(H)
Stand-Alone Panel w/o Rack: 8.5”(D) x 19”(W) x 23.5”(H)
Weight: 153 lbs. with Rack / 79 lbs. w/o Rack
D W
S-400
400 AMP
DISCONNECT
INPUT CONNECTIONS
MUST BE MADE
IN THE FOLLOWI NG
ORDER:
1) CONNECT GROUND
2) CONNECT NEUTRAL
3) CONNECT PHASES
DISCONNECT IN
REVERSE ORDER
GND
GND
GND
120/208V 3Ø OUTPUTS 400A PER Ø MAX
NEUT
NEUT
NEUT XØ
YØ
YØ
120/208V 3Ø INPUTS 400A PER Ø MAX
NEUT
NEUT
NEUT
XØ
X Ø YØ
FRONT SIDE BACK
Atlanta 404-214-4800 | Chicago 847-227-5171 | Dallas 214-630-1963 | Denver 303-341-4848
Detroit 248-526-5290 | Las Vegas 702-942-4774 | Las Vegas / Henderson 702-294-4805
Los Angeles 818-252-2600 | Mount Vernon 914-662-3540 | Nashville 615-834-3190 | New Windsor 845-567-5700
New York 212-589-5400 | North Bergen 201-758-4000 | Orlando 407-855-8060 | Toronto 905-270-9050
PRG Series 400 and Virtuoso® are trademarks of Production Resource Group, LLC. Neutrik® and PowerCon® are registered trademarks of Neutrik AG.
©2008 Production Resource Group, LLC. All Rights Reserved. Specifications are subject to change without notice. Version: August 2008
XØ
YØ
ZØ
ZØ
ZØ
ZØ
H
www.prg.com