Audico Avec ADA 8x8 datasheet english.pub

ADA 8x8 Central Unit

Notes
AUDICO SYSTEMS OY
P.O.Box 39
Ruunikkokatu 2
Fi 20381 Turku
Finland
Tel. + 358 –2 – 415 5400
Fax. + 358 –2 – 415 5450
audico@audico.fi
www.audico.fi

The real heart of the digital Audico Avec, Public Address
and Voice Evacuation system, is the Audico
ADA 8x8 central unit.
The ADA 8x8 is a very effective and compact unit. It
has versatile analog and digital audio inputs, effective
digital signal processing circuitry and matrix, built-in
prerecorded spoken message player and even 8 digital
150W power amplifiers. The Audico Avec accommodates
also system surveillance according to EN
60849 standard. It’s certified by authorized certification
body.
All this in a single 2U high 19” device.
Audico Avec digital Public Address and Voice Evacuation system
AUDICO ADA 8x8 CENTRAL UNIT
Audico Avec is configured using intuitive and easy to use Avec software, the file is finally downloaded to the ADA 8x8
V 1.01
• EN 60849 certified Voice Evacuation system
• 8 independent 150W @ 8 Ohms amplifiers
• Digital matrix 7x8
• 7 analog audio inputs, mic/line level
• 2 digital SPDIF inputs
• Built-in message/advertisement player
• Messages in USB-memory-stick
• Calendar and timer functions
• Phantom voltage for microphones
• 8 control contact inputs
• 8 control contact output
• System bus for top hierachy level devices
• Local bus for lower hierachy devices
• Efficient signal processing (DSP)
• Volume and source controls on users’ panel
• RS 232 serial input for external control

MAINS INLET AND FUSES
ADA 8x8 is connected to 230V operation voltage
using standard mains plug.
ADA 8x8 contains two separate parallel low voltage
power units. Both power supplies have dedicated
fuse at the rear panel.
ADA 8x8 must be equipped with external UPS device
when erecting a system according to the EN 60849
standard.
Fuse size is 3,15AT
SPEAKER OUTPUTS
ADA 8x8 contains 8 pcs 150W digital power amplifiers.
8 Ohms loudspeakers may be connected directly to
the speaker outputs. When 50-70-100V speakers
are used the ADA 8x8 must be equipped with ALT
8x8 line transfer unit. It converts the 8 Ohms outputs
to desired line voltage.
The ALT 8x8 provides also priority voltage outputs,
individually for each line (24VDC).
RS-232 INTERFACE
The RS232 interface at the rear is used for monitoring
the running of the ADA 8x8’s operation system.
Suitable software is for example Windows Hyperterminal.
ADA 8x8 can be controlled thru USB port
using special RS232/USB adapter.
24VDC OPERATION VOLTAGE OUTPUT
The 24DC power output is used to supply power to
the ALT 8x8 line transfer unit. The same voltage is
used also for priority voltage. Priority voltage is used
to bypass possible attenuators in rooms during paging
or alarm to ensure the message is heard everywhere
in the building.
DIGITAL OPTICAL INPUTS AND OUTPUTS
(SPDIF)
ADA 8x8 can handle digital audio signals directly.
Digital audio is brought to ADA 8x8 by using optical
SPDIF-cable.
The optical inputs are activated by configuration software,
the corresponding analog inputs must be disabled.
SPDIF input 1 is parallel to analog inputs 1 and 2,
SPDIF 2 is parallel to analog inputs 5 and 6.
FAN
The ADA 8x8 is equipped with a fan. The rotation of
fan is also monitored and any fault is reported to surveillance
system.

SYSTEM & LOCAL OVERRIDE AUDIO OUT
Both paging and alarm signals can be configured to
these outputs. The outputs are mainly intended to
feed paging audio to external amplifers or other systems.
CTRL ALT 8x8 CONTROL DATA TO ALT 8x8
The ALT 8x8 delivers priority voltage to wanted lines
according the data from ADA 8x8.
DEVICE ADDRESS DIP-SWITCH
Every ADA 8x8 in a system must have own individual
device address in the same order as they appear on
the configuration software. The first main unit has
address one, then two etc.
CONTROL OUTPUTS
The control outputs may be configured to activate on
diverse situations, like paging, alarm, fault-indication,
firebell muting etc. The output is open-collector type.
CONTROL INPUTS
The control inputs may be used to active different
ADA 8x8 actions like activate a paging, change preset,
play message, alarm etc.
MIC/LINE INPUTS
7 pcs microphone/line inputs.The connector is removable
3-pins plug. Each input has own input sensitivity
trimmer. The mic/line selection is done using the
configuration software.
SYSTEM BUS & LINK
Audico Avec devices are connected together using
either system or local bus. The devices connected to
the system bus can be used to control all ADA 8x8’s
in a single installation. Maximum number of devices
in a single bus is 32.
LOCAL BUS
The local bus is used to connect devices that are
intended to be used only locally within the cover area
of a single ADA 8x8. Typically local paging unit and
volume controllers are such locally operated devices.
USB-MEMORY STICK CONNECTOR
The alarm and other messages are stored in wavformat
to a USB-memory stick. The stored sound files
can be played as chime, alarm or information message
triggered by timer, paging, control input or a fault
etc.
There is another USB - jack inside the ADA 8x8 for
non-removable messages.

ADA 8x8 simplified block diagram

ADA 8x8 CENTRAL UNIT
Audico code 30010
EAN code 6430029190019
Signal processing and routing characteristics
8 digital power 150W @ 8 Ohms amplifiers
7 analog audio inputs, configurable either to mic or line level
Phantom-voltage for electret microphones
2 SPDIF digital stereo inputs
2 SPDIF digital stereo outputs
Internal message player, security messages in internal memory,
unlimited number of messages in USB memory stick. (wav)
Input channels digital signal processing (DSP), 7 channels
Input level, mic or line
Type of signal: digital/analog
Parametric equalizer, 3 band
Digital routing
Level control
Output channels digital signal processing (DSP), 8 channels
Tone control
Parametric equalizer, 5 band
High pass filter, frequency freely selectable
12 or 24 dB/octave, filter: Butterworth, Linkwitz- Riley or
Bessel
Delay max 4ms
Compressor /limiter
Volume control
Connection buses and I/O’s
Local bus (CAT5) for paging and control devices operational within
one ADA 8x8 only
System bus (CAT5) for paging and control devices operational over
whole system, max 32 devices
System bus link connector for chaining to next ADA 8x8
Front panel USB connector for configuration file down/upload
Rear panel and internal USB jacks for message memory sticks
8 control contact inputs, operation configurable
8 control contact outputs, operation configurable
Priority data for controlling the ALT 8x8 line transfer unit
System operation
System is expandable by adding required number of ADA 8x8 units.
Up to 256 speaker lines / paging zones
Possibility to use local programme sources in any ADA 8x8.
System surveillance:
Device and system monitoring according to EN-60849 standard
Automatic switch-over to a another ADA 8x8 if master ADA fails
Power supply voltage and temperature monitoring
Fan rotation monitoring
Requirement for Voice Evacuation System’s Main
User
Standard EN-60849 sets also guidelines for the user
of the installed system. The main user must take care
of system maintenance, testing, keep the logbook
and ensure all other users are well trained to use the
system.
We have prepared a booklet guiding the user as well
the installation and service companies to set-up and
run a system according the EN standard.
V 1.01
Audico Avec digital Public Address and Voice Evacuation system
TECHNICAL CHARACTERISTICS
Operation voltage 230VAC
Max power 950W
Required maximum alarm-on UPS capacity is 1kVA
Required ready-state UPS capacity is 200VA
(system on but no audio signal)
Analog audio inputs 7 pcs
Control I/O’s 8 / 8 pcs (open-collector)
SPDIF in/out 2 pcs
System bus max 32 device, CAT 5
Local bus max 32 device, CAT 5
Outputs 8 pcs each 150W@8 Ohms
The ADA 8x8 is Rohs-compliant, it is tested according
all relevant safety and electromagnetic compatibility
standards (EMC).
The Audico Avec product family is certified according
to EN-60849 standard (Sound System for Emergency
Purposes).
Dimensions
W x H x D 483 x 88 x 380 mm
Carton W x H x D 540 x 460 x 170 mm
Volume 0,042m 3
Weight / net 8,5 kg
Weight / gross 9 kg
Accessories
- mains cable with Schuko-plug
- USB A-B cable for downloading
- 1 GB USB memory stick
- installation and operation manuals
- configuration manual

AUDICO AVEC ACCESSORIES
ALT 8x8 Transformer unit
• Used to convert ADA 8x8’s low impedance
outputs to 50-70-100V lines
• Supplies also 24VDC priority voltage
AAE 800 Paging and control unit
• Paging
• Programme selection and volume control
• Preset activation
AAE 804 Fireman’s microphone
• High priority paging
• Prerecorded evacuation message play buttons
Audico Avec configuration software
• Used to set-up the system
• Runs in a standard Windows PC
• Requires USB-port
• Requires installation of a USB gadget-driver
AUDICO SYSTEMS OY
P.O. Box. 39 (Ruunikkokatu 2)
20381 Turku, Finland
Tel. +358- 2- 415 5400
Fax: +358- 2- 415 5450
VAT FI 0982651-1
AAE 806 Paging and control unit
• Paging
• Programme selection and volume control
• Preset activation
• 6 buttons to play prerecorded messages
AAI 800 Preset buttons and audio input
• 3 Preset activation buttons
• Audio input with level control
ASV 800 Programme and volume control
• Up-down buttons to choose channel
• Up-down buttons to set volume
AEU 100 Line end unit
• Improves line monitoring performance
• Installed to end of each monitored speakerline
www.audico.fi
audico@audico.fi