1411, Top Gun Tub & Tile Sealant.qxp - PPG Industries

TOP GUN ®1411PPG Architectural CoatingsGENERAL DESCRIPTIONTOP GUN ® Tub and Tile Sealant a 100% acrylic product for usearound tubs, showers, sinks and most any other household applicationwhere a flexible, watertight seal is needed. Provides adurable finish that remains bright white, adheres to most surfaces,and the cured sealant is mildew resistant.PRODUCTS1411 Bright WhiteTOP GUN ® Tub and Tile SealantRECOMMENDED USESShowersSinksCounter TopsCeramic TilePlumbing FixturesFEATURES / BENEFITSPaintableInterior/ExteriorCrack ResistantWater Clean-upPRODUCT DATAData below is based on Bright White 1411.Product Type:Acrylic PolymerVOC (theoretical) 200ºF (>93ºC)Meets the performance requirementsof ASTM C-834, Class-NF.Superior stain and dirt resistance.Provides a flexible durable seal.Note: This product is not formulated with lead or mercurycontaining materials.

TOP GUN ® 1411PPG Architectural CoatingsTOP GUN ® Tub and Tile SealantGENERAL SURFACE PREPARATIONClean surface of residual soap, mildew, loose grout and old caulk. Rinse the surface thoroughly. Apply TOP GUN Tub and TileSealant when the surface is dry. Areas with existing mold or mildew, should first be cleaned with a mild bleach solution.WARNING! If you scrape, sand, or remove old paint, you may release lead dust or fumes. LEAD IS TOXIC. EXPOSURE TO LEADDUST OR FUMES CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANTWOMEN SHOULD ALSO AVOID EXPOSURE. Wear a properly fitted NIOSH-approved respirator and prevent skin contact to controllead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and yourfamily by contacting the USEPA National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead. Follow theseinstructions to control exposure to other hazardous substances that may be released during surface preparation.DIRECTIONS FOR USERead all label and Material Safety Data Sheet (MSDS) information prior to use. MSDS are available through our website or bycalling 1-800-441-9695. USE WITH ADEQUATE VENTILATION. KEEP OUT OF REACH OF CHILDREN.Permissible temperatures during application:Temperature Range:Dew Point:Air and surface40ºF to 110ºF (43.3ºC)Optimum product temperature60ºF to 80ºF (16ºC to 27ºC)Surface must be at least 5ºF (3ºC) above the dew point.Application Information: Install backer-rod uniformly into deep cracks to control sealant depth. For cracks up to 1/2 inch wide,set the backer-rod from 1/4 to 1/2 inch deep. Bond breaker tape may be used for joints not deep enough for backer-rod.Remove cap and trim nozzle to desired bead size. Immediately upon application, bead may be smoothed with a sponge or puttyknife. Clean up excess caulk with damp cloth before it dries. Allow caulk to cure 36 hours before exposing to water (longer incool or humid conditions).SHIPPINGFreight Classification: PAINT OR PAINT RELATED MATERIALPackaging: 12-5.5 Ounce Tubes per cartonPPG Architectural Finishes, Inc. believes the technical data presented is currently accurate: however, no guarantee of accuracy, comprehensiveness, or performance is givenor implied. Improvements in coatings technology may cause future technical data to vary from what is in this bulletin. For complete, up-to-date technical information, visit ourweb site or call 1-800-441-9695.PPG Industries, Inc.Architectural CoatingsOne PPG PlacePittsburgh, PA 15272www.ppg.comTechnical Services1-800-332-6270Architect/Specifier:1-888-PPG-IDEAPPG Industries, Inc.One PPG PlacePittsburgh, PA 15272www.ppg.comNo.1411 1/2008