Installation Instructions 30-4100.pdf - THMotorsports.net

More documents

Recommendations

Info

You can purchase this part at: http://thmotorsports.comGauge-Type UEGO Controller InstallationRED Connect to a switched 10-18 volt power source utilizing a 10A fuse.BLACK Connect to a clean power ground.*WHITE Connects to any Stand Alone ECU unit that accepts a 0-5 volt input.*BLUE Connects to a RS-232 com port for hyper-terminal data logging.*optional (see below)Analog OutputIf the AEM UEGO gauge is to be connected to an AEM EMS, the UEGO gauge’sWHITE Analog Output wire shall be connected to an EMS Lambda input. Locating asuitable Lambda input channel can be done using the Application Notes provided withthe EMS. If the Application Notes are not readily accessible, a current list of AEMEngine Management Systems is illustrated below.Lambda input channel locations of current EMS application list ( see EMSinstructions for ECU connector pictures)AEM EMS P/N Lambda #1 Pin Lambda #2 Pin30-1000/1001/1002/1040 D14 D1630-1010/1012/1050/1052 C16 A2330-1020/1060 D7 D1430-1030/30-1070 C13 C1430-1100/1101 B47 B4830-1110 1C 9C30-1120/1121/1130 B6 B1430-1300 4 6630-1310/1311/1312/1313 76 7530-1400 29 4330-1401 44 4330-1510 C2-31 C2-3330-1600/1601/1602/1603 19 NA30-1610/1611/1612 46 5230-1620/1621/1622 29 5530-1710 2N 4J30-1720 C3 D330-1800 C3 A230-1810 D19 B17Page 4More installation manuals at: www.thmotorsports.net
You can purchase this part at: http://thmotorsports.comBelow is a list of AFR values that should be entered into the 02 Sensor #1(#2) Cal Tableif inputting the analog signal to an AEM EMS. These calibration table(s) are found in theAEMPro software: Setup | Sensors | Oxygen Sensor | Oxygen Sensor #1(#2)When connecting to AEM’s EMS, make sure to verify that the O2 #1 Gain option is setso the voltage from the O2 #1 Volts parameter matches the voltage input at the EMSfrom the O2 sensor. An easy way to do this is to disconnect the UEGO sensor from theUEGO gauge. When in this state, the UEGO gauge will output 2.35 volts. You can thenadjust the O2 #1 Gain until the O2 #1 Volts display in AEMPro reads 2.35 volts.02 Volts Gasoline AFR Methanol AFR Propane AFR Ethanol AFR CNG AFR0.00 10.00 4.42 10.72 6.14 9.900.16 10.32 4.56 11.06 6.34 10.210.31 10.62 4.69 11.38 6.52 10.510.47 10.94 4.83 11.72 6.72 10.830.62 11.24 4.96 12.05 6.91 11.120.78 11.56 5.11 12.39 7.10 11.440.94 11.88 5.25 12.73 7.30 11.761.09 12.18 5.38 13.05 7.48 12.061.25 12.50 5.52 13.40 7.68 12.371.40 12.80 5.65 13.72 7.86 12.671.56 13.12 5.79 14.06 8.06 12.991.72 13.44 5.94 14.40 8.26 13.301.87 13.74 6.07 14.72 8.44 13.602.03 14.06 6.21 15.07 8.64 13.922.18 14.36 6.34 15.39 8.82 14.212.34 14.68 6.48 15.73 9.02 14.532.50 15.00 6.62 16.08 9.22 14.852.65 15.30 6.76 16.40 9.40 15.142.81 15.62 6.90 16.74 9.60 15.462.96 15.92 7.03 17.06 9.78 15.763.12 16.24 7.17 17.40 9.98 16.073.27 16.54 7.30 17.73 10.16 16.373.43 16.86 7.45 18.07 10.36 16.693.59 17.18 7.59 18.41 10.55 17.003.74 17.48 7.72 18.73 10.74 17.303.90 17.80 7.86 19.08 10.94 17.624.05 18.10 7.99 19.40 11.12 17.914.21 18.42 8.13 19.74 11.32 18.234.37 18.74 8.28 20.08 11.51 18.554.52 19.04 8.41 20.40 11.70 18.854.68 19.36 8.55 20.75 11.89 19.164.83 19.66 8.68 21.07 12.08 19.464.99 19.98 8.82 21.41 12.27 19.78Page 5More installation manuals at: www.thmotorsports.net
Page 6 and 7: You can purchase this part at: http
Page 8 and 9: You can purchase this part at: http
Page 10: You can purchase this part at: http

Installation Instructions 30-4100.pdf - THMotorsports.net

Create successful ePaper yourself

Delete template?

Save as template?