Titan Owner's Manual - Snapsafe

SNAPSAFE TITANFEATURES:Top and BottomThanks for purchasing a SnapSafe Titan. Now you havethe peace-of-mind knowing your valuables are protectedfrom loss due to fire or theft. Best of all, you can easilylocate or relocate this protection anywhere piece-by-pieceto any room in minutes. The SnapSafe Kwik-LockModular Assembly System offers all the impregnabilityof a welded safe in an easy-to-assemble modular design.• Delivered right to your door• Assembles in minutes without tools• Kwik-Lock ModularAssembly System• Sledgehammer and pry-barresistant 3/16” solid steel door• Thick steel exterior walls• 2300°F one-hour Fire Shieldprotection• Heat activated door fire seals• Secures 12+ long guns• Nine slot full gun rack• Option Between UL Security Listedlocks: Digital or Mechanical• Eight ¾” chrome steel live locking bolts• Spring-loaded relocker• Powder coated finish• Lined interior• Adjustable lined shelves• Includes 1 full shelf and full gun rackand a half gun rack with 2 half shelves• Professional grade “non breach seal”dead bolt door• Predrilled for floor mounting• Lifetime warrantySideFrontCUSTOMER SERVICESNAPSAFE TITANSPECIFICATIONS:MODEL : TitanFor all Customer Service questions call toll free:1-877-214-4470 fax: 1-772-288-6824Or write: SnapSafe Inc. Customer Service3721 Doubleton Drive Stuart, FL 34997Or Email: info@snapsafe.comEXTERIOR : 59”H x 22”W x 17 1/2”D(Add 3” for handle)INTERIOR : 55 1/8”H x 17”W x 14 1/2”DDOOR OPENING : 52”H x 14 3/4”WLOCKING BOLTS : 8CAPACITY : 12 + Long GunsWEIGHT : 388 Lbs. - 9 Gauge3

TopRight SideLeft SideBottomBackTITAN PARTS LISTTop InteriorPanelPart #1 – LEFT SIDEPart #2 – TOPPart #3 – RIGHT SIDEPart #4 – BOTTOMDoorFrameLeftInteriorPanelRightInteriorPanelPart #5 – BACKPart #6 – DOOR FRAMEPart #7 – TOP INTERIOR PANELPart #8 – LEFT INTERIOR PANELPart #9 – RIGHT INTERIOR PANELPart #10 – BOTTOM INTERIOR PANELPart #11 – DOOR HANDLE SPOKESPart #12 – DOORPart #13 – DIVIDER (Optional)BottomInterior PanelStand Safe UprightAnd Hang DoorDividerGun RackDivider TopShelvesPart #14 – GUN RACK DIVIDER TOP (Optional)Part #15 – SHELF HARDWARE (not pictured)ASSEMBLING YOUR SNAPSAFE TITAN1. Unpack and lay out all parts.2. Thread DOOR HANDLE SPOKES (Part #11) onto the hub on DOOR (Part #12).3. Install a fresh high-quality 9V battery in the Entry Keypad. (See pgs 8 and 9).4. Important – Remove temporary door hinge bolts from door hinges.5. Enter the factory combination code and open the DOOR, then lift it off theDOOR FRAME (Part #6) and set aside.6. Assemble Top, Bottom and Sides (Parts #1 through #4) first. Then Kwik-Lock the entireassembly onto the BACK (Part #5).7. For additional help watch our “Live Action Assembly Video” on the “Features”#1#8#18#14#7#2#5Part #16 – LOWER SHELF (Optional)Part #17 – LOWER SHELF (Optional)Part #18 – UPPER SHELFPart #19 – KWIK–LOCK HARDWARE (not pictured)Part #20 – FULL GUN RACK (not pictured)#9#3page at www.snapsafe.com.Notes:1. Each part is marked with an assembly number, orientation and instructions.2. Each part’s orientation: TOP, BOTTOM, FRONT, etc. matches its orientation inthe assembled vault. LEFT and RIGHT are as you face the front of the vault.3. For easier assembly of the Kwik-Locks, remove the FIRESHIELD blankets fromthe TOP, BOTTOM and SIDEWALLS and then stuff them back into placebefore interior assembly.4. Screw on Kwik-Locks loosely at first. Once all Exterior Panels are alignedand seated, tighten the Kwik-Locks. Tightening with a tool is not necessary.5. The INTERIOR SIDE PANELS are designed to fit snuggly. Insert them throughthe door opening bottom-to-top and then slide into final position front-to-back.6. Insert the INTERIOR BOTTOM PANEL through the door opening between thefront and back shelf strips and then drop into position front-to-back.#11#12#6#4#13#10#17#164 5

Part #2 – TOPYOUR COMBINATION CODE• Your factory preset combinationcode is 1-2-3-4-5-6.• It is recorded in a small envelopewired to the door handle of your vault.Store this combination in alocation other than your vault.CHANGING YOURCOMBINATION CODEWrite down and store a new6-digit code (Do not store in vault).You cannot set the combination codeto six (6) zeros (0).Part #1LEFTPart #5 – BACKPart #4 – BOTTOMPart #7 – TOP INTERIOR PANELPart #10BOTTOM INTERIORPANELPart #3RIGHTPart #6 – DOOR FRAMEPart #13DIVIDER(Optional)Part #12 – DOORPart #14GUN RACK DIVIDER TOP(Optional)Part #18UPPER SHELFPart #16LOWERSHELF(Optional)Part #17LOWERSHELF(Optional)OPENING AND CLOSINGYOUR VAULTOpening:1. Enter the 6-digit combination code.2. Rotate 3-spoke handle clockwiseinto the open position and pull dooropen.3. The Entry Keypad relocks in 4seconds after a valid code hasbeen entered.4. The Entry Keypad will returnto“standby” status with a long beepsound if there is no operation in 10seconds after the system has beenactivated.5. If you enter an incorrect combination4-times in a row, the lock will shutdown for 5-minutes.Closing:1. Close vault door.2. Rotate 3-spoke handle counter-clockwise to the closed position until youhear bolts engage.1. Open vault door and lock it inopen position.2. Enter zero (0) six (6) times. Onebeep sounds indicating the entry isvalid and the system is awaiting acode change.3. Enter the existing 6-digit code.One beep sounds, indicating theentry is valid.4. Enter a new 6-digit code. One beepsounds, indicating the entry is valid.5. Re-enter the new 6-digit code. Onebeep sounds, indicating that thecode in step 4 and 5 are the sameand that the code change issuccessful.6. If three beeps sound, the codechange was unsuccessful, and theexisting code is still valid. Repeatsteps 2 – 5.7. Enter and check new code 3-timesbefore closing door.Note: Each step in the code changeprocess must be completed in 10seconds or the system reverts backto “standby” status.Part #8LEFT INTERIORPANELPart #9RIGHT INTERIORPANELPart #20FULL GUN RACK6 7

DOUBLE SAFEGUARDINGVALUABLE PAPERSYour SnapSafe Titan’s Fire Shieldblankets are rated at 2300ºF forone-hour. However, we recommend thatif you are going to be putting importantpapers in the vault, you first put it in afire resistant document box,and then put it in the vault.BOLTING DOWNYOUR VAULTWe recommend bolting your vault tothe floor using two ¼” wedge anchorconcrete bolts through the predrilledholes in the BOTTOM of the vault.LOW BATTERY ALERTYour lock has a “Low Battery Alert.”If the Entry Keypad beeps repeatedlyduring an unlocking, the battery is lowand needs immediate replacement.INSTALLING ANDREPLACING ENTRYKEYPAD BATTERYYour vault is equipped with an electroniclock made with non-volatile memory,meaning your combination code isretained even if the batteries are nolonger powering the lock. If thishappens, simply replace the batteries.Install only a high-quality alkalinebattery in the compartment in the backof the Entry Keypad following thesesteps.1. Remove Entry Keypad. Slide it upand carefully pull it away from thevault door. (Fig.1)Note: Do not pull the Keypad as toomuch force may damage the cable.2. Snap new battery into the connectorclip, and slide it into the batterycompartment top down so that thewires will not be pinched between thebattery and the vault door. (Fig.2)3. Fold the connection cable inside theKeypad (Fig.3)4. Position the Keypad over themounting screws, and slide it downinto position.Note: Make sure the connection cableis not trapped between the Keypadand the door or rubs or tangles on themounting screws. (Fig.4)8 9

CARE AND MAINTENANCENOTES:With a little care and maintenance your SnapSafe Modular Vault will lasta lifetime. Keep the door hinge pins lightly greased so that the door openssmoothly. Vacuum the inside from time to time, and wipe down the outsidewith a soft cloth and mild detergent. Never use harsh solvents or abrasiveson any surfaces, as they may damage the exterior finish or interiormaterials.SNAPSAFE ® LIFETIME WARRANTYWere going to take care of you.Period.We have built products and a company we are proud of and want you to beas well.If you ever experience a fire or attempted break-in we’ll repair or replaceyour vault at no charge. (All you have to do is to forward the report fromthe proper investigative agency)10 11

IMPORTANT!Keep for Your Records.Do not store this booklet and information in your vault.Date of receipt of vault__________________Vault serial number_____________________(Located on plate on the bottom of door frame)Customer Service: 3721 Doubleton Drive Stuart, FL 349971-877-214-4470 Fax: 772-288-6824 Email: info@snapsafe.com