Specification AXIOM6060 Oscillator type : OCXO with Low ... - AXTAL

Enclosure drawingOrdering Code:Model (Specification) Product Category Frequency [MHz]AXIOM6060EM100.000FMLATExample: AXIOM6060‐FM – 100.000 MHzGmbH & Co. KGAXIOM6060www.axtal.comRoemerring 9 page 2(5) fon: +49 (6261) 939834D‐74821 Mosbach fax: +49 (6261) 939836GermanyE‐mail: info@axtal.com

Environmental conditionsTest Reference Test conditionsRadiationTBD, up to 100 kRad (Si) total doseVibration, random,non operatingMIL‐STD‐202F,Method 214Cond. I, Letter J, PSD 1.0 G²/Hz,37.8 G rms, 3 min per axisVibration, highfrequency, nonMIL‐STD‐202F,Meth.204Cond. D. 20G, 10 Hz ~ 2000 Hz, 20 minper cycle, 12 cycles each axisoperatingMechanical shock MIL‐STD‐202F, Cond. F, 1500 G, 0.5 ms, half‐sineMethod 213Ambient Pressure MIL‐STD‐202F, Between 1 atm and hard vacuumConstant Acceleration MIL‐STD‐202F, 10G, 0.5G/sec, duration 2 minMethod 212HumidityMIL‐STD‐202F,Method 10360 % RH @ 40°C for 96 hoursScreening Procedure (MIL‐PRF‐55310 Product Level S)Test Reference Test conditionsElectrical Measurement Table 1at room temperatureRandom Vibration MIL‐STD‐202F,Meth. 214, Cond. 1‐BPSD = 0.04 G²/Hz, 7.56 Grms, 5 min peraxisThermal Shock MIL‐STD‐202F,Meth. 107, Cond. A1‐40°C ~ +80°C, 25 cycles, non‐operating,5 min transfer time, 15 min dwell timeElectrical Measurement Table 1at room temperatureBurn‐In (Load) MIL‐PRF‐55310 @ 85°C over 240 hours, f/f < ± 1 ppmElectrical Measurementat room temperatureTable 1@‐35°C, +25°C, +70°C, f/f < ± 50 ppb,Output level (13±1) dBElectrical Measurementat High and Low@‐30°C, +25°C, +70°C, f/f < ± 50 ppb,Output level (13±1) dBTemperatureSeal Test (Gross Leak) MIL‐STD‐202F,Meth. 112, Cond. DRadiographic Inspection MIL‐STD‐202F,Meth. 209External VisualInspectionMIL‐STD‐883Meth. 2009ESCC 20500Group A InspectionTest Reference Test conditionsGroup A Inspection MIL‐PRF‐55310 Table 5, Product Level S100 %Clause 4.7.1.4Note:Electrical measurements performed during screening are not repeated during Group A inspectionGmbH & Co. KGAXIOM6060www.axtal.comRoemerring 9 page 3(5) fon: +49 (6261) 939834D‐74821 Mosbach fax: +49 (6261) 939836GermanyE‐mail: info@axtal.com

Group B Inspection (Aging Test)Test Reference Test conditionsGroup B Inspection MIL‐PRF‐55310 Table 5, Product Level S100 %Clause 4.7.1.5Final ElectricalMeasurement at roomtemperatureTable 1Group C Inspection (LAT) on 2 piecesTest Reference Test conditionsRandom Vibration MIL‐STD‐202F,Meth. 214, Cond. 1 JPSD = 1.0 G²/Hz, 37.8 Grms, 3 min peraxisMechanical Shock MIL‐STD‐202F, 1500 G, 0.5 ms, half‐sineMeth. 213, Cond. FThermal Shock MIL‐STD‐202F,Meth. 107, Cond. B1‐65°C ~ +125°C, 25 cycles, nonoperating,5 min transfer time, 15 mindwell timeHigh TemperatureStorage‐ 24 hours @ ‐30°C, 24 hours @ 70°C,2 hours min. at ambient temperatureElectrical Measurement Table 1at room temperatureSeal Test (Gross Leak) MIL‐STD‐202F,Meth. 112, Cond. DExternal VisualInspectionMIL‐STD‐883Meth. 2009ESCC 20500Model ConstructionsItemQuartz CrystalElectricalComponentsEngineering Model(EM)Synthetic HiQ Quartz,SC‐cut, HC‐35/U4‐pointPassives: COTSActives: from samemanufacturer as theHiRel partsForm‐Fit Function, Albody with Ni finishMechanicalComponentsWorkmanship IPC610 ECSS‐Q‐ST‐70‐08CandECSS‐Q‐ST‐70‐38CTests Acceptance Testing Screening andQualificationTestingQualificationModel (QM)Flight Model(FM)Lot AcceptanceModels (LAT)Synthetic HiQ Synthetic HiQ Synthetic HiQSwept Quartz IAW Swept Quartz IAW Swept Quartz IAWESCC3501, SC‐cut, ESCC3501, SC cut, ESCC 3501, SC cut,HC‐35/U 4‐point HC‐35/U 4‐point HC‐35/U 4‐pointHiRel Parts HiRel Parts HiRel PartsAs FM NiAu surface finish As FMECSS‐Q‐ST‐70‐08CandECSS‐Q‐ST‐70‐38CScreening andAcceptance TestingECSS‐Q‐ST‐70‐08CandECSS‐Q‐ST‐70‐38CScreening andAcceptance Testingand LAT (Group C)GmbH & Co. KGAXIOM6060www.axtal.comRoemerring 9 page 4(5) fon: +49 (6261) 939834D‐74821 Mosbach fax: +49 (6261) 939836GermanyE‐mail: info@axtal.com