Download - Pro-Align

HawkEye Digital ImagingHigh-defi nition imaging sensors continuouslymeasure wheel target position and orientation,providing the same alignment measurements asconventional sensors.HawkEye Sensors use multi-dimensionalmodeling to provide accurate alignmentmeasurements. The operator can use either liveplane mode, which uses the targets as a referenceplane, or the traditional alignment mode, whichuses the rack runways as a reference plane.Four stationary cameras(one for each wheel)measure the positionand orientation ofalignment targets.HawkEye SensorAlignment Targets *Durability Corrosion resistant “Shatterproof” aluminum faceplate - no glass Impact-resistant housing Integrated protective bumpersEase of Use No electronics at the wheel Virtually maintenance-free No calibration Lightweight No cablesSelf-Centering AdaptorsSelf-centering wheel adaptors cover an extendedrange, allowing the adaptor to be used forpassenger car or heavy-duty truck use. Optionalextensions and adaptors are available for specialtyand hard-to-mount wheels.All models includefour HawkEye Sensor AlignmentHexagonal Targetsand Self-CenteringWheel Adapters.* Patented

HawkEye Sensor ConfigurationsSpace-Saving HawkEye Sensors Offer Enhanced Productivity in a Small FootprintHawkEye sensors can be installed within an inch of a wall, saving space at the front of your bay.The fixed-column standard configuration HS400FC1E fitsmost service bay applications.*HS400LZ1E provides a vertical camera lift with a 51-inch(1,295mm) range of motion to achieve additional lift heightor to work with the vehicle lowered to the floor.The HS400WM1E may also be mounted to the wall orceiling. When paired with the RX-P Pit In-Ground ScissorLift, the combination is ideal for drive-through service bayshandling vehicles with minimum ground clearance.The HS400FM1E Floor-mounted wide sensors are excellentfor drive-through bay applications.Other HawkEye Sensor Configurations Include:HS400DT1E - Drive-thru configuration* Sensors shown with ProAlign Column/Wall-Mount Console

SpecificationsProAlign Wheel Alignment Systems include:Mobile or column/wall mount cabinet17-inch color LCD fl at panel monitorProAlign software cartridgeLanguage specifi c keyboardOptical mouse pointing deviceColor inkjet printer.ProAlign Hawkeye Sensor Software includes:Linux operating systemFactory vehicle specifi cation databaseWork Management customer database*Passenger car programHeavy-duty truck programWinToeShim Select IICAMMSymmetry measurementsRide Height measurement (with 20-1885-1)VAG Raised Toe procedureFaster Caster measurementTurning angle difference measurementMaximum steer angle measurementAdjustments with wheels raisedZero adjustmentReverse sensor test*Work Management customer database can be enabled by adding a USB memory deviceto the ProAlign console.Power Requirements100-240V, 3.5A-1.75A, 50-60HzOptionsInfared Remote Control 146-55-1Icon Remote Indicator30-419-1-XIcon Cordless Remote Indicator †30-421-1-XXF Pod Kit(for Cordless or Remote Sensors) 20-2072-1Standard Turnplate (2 required) 25-140-1Stainless Steel Turnplate (2 required) 25-129-1Electronic Turnplates 20-1487-1Ride Height Measurement Tool 20-1885-1† Requires XF Pod Kit 20-2072-1. (Ships standard with DSP506XF or DSP508XF.)“Before” and “after” measurements canbe printed to explain service and recordwork performed. Screens and rear shimtemplates can also be printed.The optional Icon Remote Indicatorprovides the operator with completecontrol while making adjustments tothe vehicle. Available in conventionalor cordless models.Optional Hand-Held Ride HeightMeasurement Tool 20-1885-1.ProAlign Compatible SensorsHS400, DSP504, DSP506, DSP506XF, DSP508, DSP508XFVisit our website at www.hunter.comHS400 Sensors require ProAlign version 1.5 or greater software.HawkEye sensor configuration choices are depicted on the previous page. All Hawkeyesensor groups include; 4 digital cameras, 4 hexagonal targets, 4 self centering wheeladapters, 4 target supports, cables, and mounting hardware. Because of continuingtechnological advancements, specifications, models and options are subject to changewithout notice. Contact your Hunter distributor to configure a system to satisfy your needs.11250 Hunter Drive, Bridgeton, MO 63044 U.S.A.Tel: 1-314-731-3020 • Fax: 1-314-731-0132E-mail: international@hunter.comIntel is the registered trademark of Intel Corporation. CAMM, HawkEye, ProAlign, Shim-Select and WinToe are trademarks of Hunter Engineering Company.Copyright © 2009, Hunter Engineering Company0309FAP2M.1.01