Trouble Godes

More documents

Recommendations

Info

IEngine management IErasing Method 2Ensure ignition switched OFF.Method 1Disconnect battery earth lead for 10 seconds.Switch ignition ON.WARNING: Disconnecting the battery may erase memory fromConnect LED test lamp between data link connector (DLC)electronic units (e.g. radio, clock).terminal C3 and battew ~ositive a.Bridge data link connect& (DLC) terminal C2 and earth witha switched lead - contacts normally open a.Operate switch for 2,5-5 seconds.LED or MIL will now flash trouble code 12.Repeat switch operation until code 11 is displayed.Operate switch for 10-20 seconds.Switch ignition OFF.<strong>Trouble</strong> code identificationFlash type Fault location Probable causeI14 I Engine coolant temperature (ECT) sensor I Wiring, ECT sensor, ECM16 I Exhaust gas recirculation (EGR) soienoid I Wiring, relay module, EGR solenoid213941Fuel lever position sensorMalfunction indicator lamp (MIL)Crankshaft position (CKP) sensorlengine speed (RPM)sensor46 I Fuel injection pump - timing control I Fuel injection pump timing495354Fuel injection timing solenoidBattery voltageEngine control module (ECM)57 I Barometric pressure (BARO) sensor I ECM58 I Glow plug control module - pre-heat I Wiring, glow plug(s), glow plug control module65666768Injector needle lift sensorGlow plug control module - pre-lpost-heatGlow plug warning lampIdle speed control (ISC) actuatorIWiring, fuel lever position sensorWiring, MIL, ECMWiring, CKPlRPM sensor, air gap, ECMWiring, fuel injection timing solenoidWiring, battery discharged, alternatorWiring, battery, ECMWiring, fuel system, injector, injector needle liftsensorWiring, glow plug control moduleWiring, glow plug warning lamp, ECMWiring, hoses blockedlleaking, ISC actuator4/Autodata I Eng~nemanagement 251
I CDTROENEngine managementXantia 2,lD Turbo XM 2,lD TurboSynergieIEvasion 2,l TD DispatchlJumpyYear: 199500Engine code: P8CSystem: Lucas EPICXM, Xantia -7998 - in fascia fuseboxXM, Xantia 7998 + - in fascia fuseboxSynergieEvasion, DispatchlJumpy 1498-*- -General informationn Refer to the front of this manual for general test conditions,terminology, detailed descriptions of wiring faults and ageneral trouble shooter for electrical and mechanical faults.Vehicles fitted with a coded keypad: When switching onignition or entering start code ensure diagnostic equipment isdisconnected from the data link connector (DLC).Accessing and erasingThe engine control module (ECM) fault memory can only beaccessed and erased using diagnostic equipmentconnected to the data link connector (DLC).The following scanner codes are applicable to the fuelsystem manufacturer's test equipment, similar and moredetailed fault diagnosis information can be obtained usingthe vehicle manufacturer's or equivalent test equipment.
Page 1: DiagnosticTrouble GodesFault locati
Page 4 and 5: Model: AX 1,011,111,4 C15 1,1/1,4 Z
Page 6: Model: AX 1,011,111,4 C15 1,111,4 Z
Page 9 and 10: 1 224 I,.,,,,,,,,I Engine managemen
Page 11 and 12: I Engine managementScannertype91011
Page 13 and 14: Model: Saxo l,4/l,6 Berlingo l,4/1,
Page 15 and 16: I Engine managementModel: Saxo 1,41
Page 17 and 18: Model. Saxo 1,6ngtne managementEras
Page 19 and 20: CITROEN Model: Saxo 1,6 MT Xsara 1,
Page 21 and 22: Engine managementModel: C3 1,4 Berl
Page 23 and 24: Engine managementModel: Xsara 1,8Ye
Page 25 and 26: Engine managementEngine code:System
Page 27 and 28: IEngine managementModel: Xsara 2,O
Page 29 and 30: I Engine managementPI 555Exhaust ga
Page 31: Model: Xsara 2,O HDi Xantia 2,O HDi
Page 34 and 35: 7Engine managementFlash typeFaW loc

Trouble Godes

Create successful ePaper yourself

Delete template?

Save as template?