SMACNA Master Index of Technical Publications - Sheet Metal and ...

positive or negative pressure, PVC 11
rated pressure, PVC 10
reinforced, DCS 1.12
reinforcement, DCS 1.15, 1.48
rigidity class, PVC 10
sequence, DCS 7.8
size, RCDC 4.6
slip and drives, DCS 1.5
spacing, RCDC 4.5, 7.59
standing seams, DCS 1.54
stiffener, RCDC 4.5
tables, DCS 1.16; DD 6.14; RCDC 7.1,
7.37, 7.37, 7.46, 7.46, 7.56, 7.59, 7.61
thickness, RCDC 7.1, 7.10, 7.19, 7.28
transverse joint reinforcement, DCS 1.13,
1.24
types, RCDC 3.1
unit conversion, RCDC 4.2
units, RCDC 4.2
unreinforced, DCS 1.12, 1.42, 1.44
vanes, DCS 2.4
Reducers, DD 5.9; RNDC 12.33, 15.13
Reentrainment, IAQ 3.1
References, APP iv; BSAR 1.24, 2.31, 3.19, 4.6,
5.7, 6.6, 7.9, 8.19; DCS v; FGDC v; FSDG R.1;
IDC 95; MGW v, 4.4, 5.10, 9.3; OBUC A.1; PVC
xv, 4, 51
Refrigerant(s), TAB 9.12, 10.4
cautions, BSAR 8.12
cycle, APP 12.1
design, RCSI 11.6
gas, RCSI 11.7
listing, BSAR 8.13
piping, APP 14.29
retrofit, BSAR 8.17
substitutes, BSAR 8.11
temperature, APP 12.1
types, BSAR 8.11
venting, RCSI 11.7
Refrigeration, ESAM 1.3, 1.5, 1.6, 2.1, 2.4, 2.5,
2.6, 2.7, 4.1, 4.7, 5.2, 5.3, 5.4, 5.6, 5.10, 5.15,
8.1, 8.6, 8.7, 11.1, 15.1, 15.2, 16.20, 17.1, 20.5,
20.6, 21.3, 21.5; TAB 10.1, 10.2
certification, BSAR 8.16
commercial, BSAR 2.20
APP HVAC Systems – Applications
ASMM Architectural Sheet Metal Manual
BSAR Building Systems Analysis &
Retrofit Manual
COM HVAC Systems Commissioning
Manual
DCS HVAC Duct Construction Standards
Metal and Flexible
DD HVAC Systems Duct Design
DEHG Ducted Electric Heat Guide for Air
Handling Systems
ESAM Energy Systems Analysis and
Management
FGDC Fibrous Glass Duct Construction
Standards
SMACNA Master Index
FRP Thermoset FRP Duct
Construction Manual
FSDG Fire Smoke and Radiation Damper
Guide for HVAC Systems
FSE Food Service Equipment Guidelines
GSSC Guide for Steel Stack Construction
IAQ Indoor Air Quality – A Systems
Approach
IDC Accepted Industry Practice for
Industrial Duct Construction
KVS Kitchen Ventilation Systems
Guidelines
LAG Accepted Industry Practices for
Sheet Metal Lagging
LTM HVAC Air Duct Leakage Test
Manual
MGW The Manager’s Guide for Welding
control, APP 3.35
cycle, TAB 10.2
design, RCSI 11.6
recovery, BSAR 8.11
systems, APP 12.1; BSAR 3.18; TAB 10.1
Refuge areas, APP 9.43
Register, FGDC 2.16
Register connections, DCS 2.18
Reglet, RSMG 2.3
Regulations, FSDG 3.1
Reheat, DEHG 2.1
coil, APP 2.4; TAB 12.7
induction, APP 8.1
system, APP 6.1
Reinforcement, See Duct reinforcement; FGDC
3.1; FRP 1.1, 1.2, 2.1, 2.5, 3.1, 5.1, 5.2, 6.2, 7.1,
7.2, 7.7, C.1, D.5; IDC 25
access door, FGDC 3.17
angle, IDC 26
attachment, DCS 1.48
bar, IDC 29
channel, FGDC 3.5, 3.6, 3.9; IDC 29
fitting, FGDC 3.7
hat section, IDC 29
I-beam, IDC 29
openings in stack, GSSC 6.5
steel filter housing, IDC 27
throat, FGDC 3.12
tie-rod system, FGDC 3.1, 3.1, 3.2, 3.3
transition, FGDC 3.16
transverse joints, DCS 1.13, 1.24
trunk, FGDC 3.13
Reinforcing member, See specific material
Relative humidity, TAB 2.9
Relays
electro-pneumatic (EP switches), APP 3.14
pneumatic-electric (PE switches), APP 3.14
positioning, APP 3.14
proportional, APP 3.14
switching, APP 3.14
two-position, APP 3.14
Release film, FRP D.5
Relief
air openings, APP 2.2
devices, TAB 10.4
OBUC IAQ Guidelines for Occupied
Buildings Under Construction
PVC Thermoplastic Duct (PVC)
Construction Manual
RCDC Rectangular Industrial Duct
Construction Standards
RCSI Residential Comfort Systems
Installation Standards
RNDC Round Industrial Duct Construction
Standards
RSMG Residential Sheet Metal Guidelines
SEIS Seismic Restraint Manual –
Guidelines for Mechanical Systems
TAB HVAC Systems Testing Adjusting
and Balancing
43