UPS control unit P o w e r s u p p lie s When the power supply fails ...

Input:Output:100 - 120 V AC200 - 240 V AC50 / 60 Hz24 V DC 10 A6-10 A Cha r . Cmax. 250 V AC / 1 A30 V DC / 1 AL N PE 12 11 14 +V +V -V -VAdj.24...26 V DCUPS control unitPower suppliesWhen the power supply fails, UPS control units take over the12/24 V DC power supplies to the installation within seconds,and guarantee plant availability for a defined length of time.Switch-mode power supplies, battery control unit andbattery providing an uninterrupted power supply.Professional signalling guarantees that all relevant signalstatuses can be evaluated on the spot. Critical statuses canalso be immediately redirected to a higher-level controller.230 V AC115 V AC8708680000CP SNT 250 W 24 V 10 APower supplyEThe battery module undertakes complete battery managementof the connected lead-acid batteries. Constant charging anddischarging plus electronic overcurrent protection guarantee anextremely long operational lifetime for the batteries.\%DC OK •Status r elays(change-overcontact)115/230 V AC50/60 Hz+-Batterycont r ol unitPE PSN PSL PSLNPE+-+-Alarm contactAccumulator+-to the load ci r cuitE.38

UPS control unitconnectPowerCP-BBU 115-230 V AC / 12 V DCCP-BBU 115-230 V AC / 24 V DCPower suppliesLWHNgL BBU+++ -- -- + + -1 2 nLoadsNgL BBU+++ -- -- + + -1 2 nLoadsNgLP/S+ +- -NgLP/S+ +- -115/230V50/60Hz115/230V50/60HzTechnical dataInputInput voltage ; 120…300 V DC; typ.115-230 V AC ±10%Input current AC; 0.5 A @ 230 V ACInput frequencyInput fuse low fuse (internal)Making current limitSurge protectionOutputOutput voltageOutput current x 9.2 A for power supplyMains failure bridge-over timeBattery charging currentBattery voltageControl at input voltageInput85…265 V AC; 120…300 V DC; typ.115-230 V AC ±10%0.8 A @ 115 V AC; 0.5 A @ 230 V AC50/ 60 Hz quency2 A slow-blow fuse (internal)Thermistor rent limitVaristor age protectionOutput12 V DC oltagemax. 15 A / max 9.2 A for power suppliesMains failure bridge-over time2.00 A y charging current13.65 V voltage0.2 % ol at input voltageInput85…265 V AC; 120…300 V DC; typ.115-230 V AC ±10%1 A @ 115 V AC; 0.6 A @ 230 V AC C50/ 60 Hz quency2 A slow-blow fuse (internal)Thermistor rent limitVaristor age protectionOutput24 V DC oltagemax. 15 A / max 9.0 A for power suppliesMains failure bridge-over time3.00 A y charging current27.3 V voltage0.2 % ol at input voltageEGeneral dataOperating temperatureStorage temperatureStatus indication harge): Battery voltage > 14.75 VdcLED yellow (Battery Low): Battery voltage < 11 VdcLED yellow (Chargin): BBU charges BatteryLED red (Fault): no AC input voltageLED red (Batterie Reverse): Battery polarizing faultLED red (Battery open): no battery connectedStandards EN 60950, IEC950EMC standards 55022, EN 55024, EN 61000-6-2, 3Approvals ;CE;General data-20 °C…+50 °C ature-20 °C…+85 °C ureLED green (Full Charge): Battery voltage > 14.75 VdcLED yellow (Battery Low): Battery voltage < 11 VdcLED yellow (Chargin): BBU charges BatteryLED red (Fault): no AC input voltageLED red (Battery Reverse): Battery polarizing faultLED red (Battery open): no battery connectedEN 50178, EN 60950, IEC950EN 55011, EN 55022, EN 55024, EN 61000-6-2, 3CSA;UL/UR;CE;General data-20 °C…+50 °C ature-20 °C…+85 °C ureLED green (Full Charge): Battery voltage > 29.5 Vdc cLED yellow (Battery Low): Battery voltage < 22 VdcLED yellow (Charging): BBU charges BatteryLED red (Fault): no AC input voltageLED red (Batterie Reverse): Battery polarizing faultLED red (Battery open): no battery connectedEN 50178, EN 60950, IEC950EN 55011, EN 55022, EN 55024, EN 61000-6-2, 3CSA;UL/UR;CE;DimensionsClamping range (rating- / min. / max.) mm 2Length x width x heightmmScrew connection4 / 0.1 / 4161 x 72.5 x 127.5Screw connection4 / 0.1 / 4161 x 72.5 x 127.5NoteOrdering dataConnection systemScrew connectionType Qty. Order No.CP-BBU 115-230VAC / 12VDC 1 9916280012Type Qty. Order No.CP-BBU 115-230VAC / 24VDC 1 9916280024NoteAccessoriesNoteBracket for wall mounting: 7920560000Bracket for wall mounting: 7920560000E.39