B45 B60 BV208DA Instructions - Gardner Bender

Vacuuming Pull Line in the Conduit1. Insert the hose in the vacuum port.2. Select the JV07 small Dial-A-Line body thataccepts the JV08, JV09 or JV12 Seal-off for conduitsizes 1 ⁄2” through 2 1 ⁄2” or the B26 Large Dial-A-Line body that accepts the BV23 or BV24 Seal-offfor conduit sizes 1 1 ⁄4” through 6”.3. Connect the hose to the Dial-A-Line body.4. Place the pull line at the far end of the conduit.5. Select the appropriate line carrier and tie the pull linesecurely to the line carrier.6. Insert the line carrier in the conduit and turn on thepower unit.VIII. MaintenanceB26 Dial-A-Line BodyBV24 Seal-Off12568 Hose AssemblyInflatableVacuuming Line in Conduitwith the Inflatables®ConduitPullLineVacuuming Dirt and Water — Each Blo-Vac comeswith a cloth filter bag that must be used when vacuumingdirt and water. Use as follows:The Blowers and Blo-Vac systems should require verylittle maintenance. If the unit should require service, seeinstructions below.Blower overheating occurs when attempting to blow linein blocked conduit or a duct filled with water having ahead greater than the water lift capability of the blower.See Table 1.The 1261 and B3000 Blowers have an automatic thermaloverload switch built into the motor. If overheatingoccurs, the switch will turn the motor off. After a cooldownperiod of 15 to 30 minutes, the motor willautomatically re-set. The motor can be restarted.Blo-Vac power units are equipped with a perforatedfilter screen, located on the under side of the motorcompartment. Occasionally the screen becomes cloggedwith lint and dust and it should be cleaned to maintainmaximum air flow.Size Conduit1/2”3/4”1”1 1/4”1 1/2”2”2 1/2”3”3 1/2”4”5”6”Blower Application1. Release the latches securing the top and centertogether.2. Remove the filter bag from the bottom tool storagesection. Slide the filter bag onto the intake canisterlocated on the bottom of the motor. The filter bagprevents dust from entering the motor. Dust and dirtwill damage the motor and cause premature failure.3. After use, clean the filter bag by shaking off theexcess dirt and store the clean bag in the lowercompartment.4. The Blo-Vac is equipped with a ball float toprevent water from entering the motor. If the ballfloat seals the motor inlet, the motor will sounddifferent from usual. Immediately turn the unit off.Empty the recovery section and check the inletscreen for lint and dirt. Clean and reassemble theBlo-Vac sections.Blo-Vac Application1/2”3/4”BV208DA1”1 1/4”1 1/2”B452”B602 1/2”3”3 1/2”4”5”Distance6”0 200 400 600 800 1000 1200 0 200 400 600 800 1000 1200REPAIR AND SERVICE INSTRUCTIONS: For repair service and parts contact your nearest GB ELECTRICAL Service Center. The GBELECTRICAL Service Center will provide complete and prompt service on all GB ELECTRICAL products.Size ConduitPARTS AND SERVICE: For quality workmanship andgenuine GB ELECTRICAL parts, select an AuthorizedGB Service Center for your repair needs. Only repairsperformed by an Authorized Service Center displayingthe official GB Authorized sign are backed with fullfactory warranty. Contact GB Electrical (414)352-4160for the name of the nearest GB AuthorizedService Center.WARRANTY: GB ELECTRICAL, INC. warrants itsproduct against defects in workmanship and materialsfor 1 year from date of delivery to user. Chain is notwarranted. Warranty does not cover ordinary wearand tear, abuse, misuse, overloading, altered productsor use of improper fluid.WARRANTY RETURN PROCEDURE: When questionof warranty claim arises, send the unit to the nearest GBAuthorized Service Center for inspection, transportationprepaid. Furnish evidence of purchase date. If the claimcomes under the terms of our warranty the AuthorizedService Center will REPAIR OR REPLACE PARTSAFFECTED and return the unit prepaid.Gardnera unit of Tools and SuppliesBender 6101 N. Baker Road, Milwaukee, WI 53209 • Phone: (414) 352-4160 • FAX (414) 352-2377 ZRPS-0134 12/98