Stripper-Crimper Machines (AMP-O-MATIC and AMP-TAPEMATIC 4 ...

AMP-O-MATIC
Stripper-Crimper
Product Facts
■ Strip and terminate wires
32-14 AWG [0.03-2 mm 2 ]
■ Fast set-up times:
10 minutes or less
■ Illuminated target area
■ Convenient scrap removal
■ Select foot switch or
wire-sensor mode of
operation
■ Lock-out/tag-out device
per OSHA Standards
#29CFR1910.147
■ Air-powered machine
operation
■ Wire breakouts down to
.72 [18]
■ Precision crimp adjustment
in .0005 [0.0127]
increments
Technical Documents
Customer Manuals
409-5855 — AMP-O-MATIC Side
Feed Stripper-Crimper
Model II Machine No.
1320895-1 and -2
409-5820 — AMP Crimp Quality
Monitor Part No.
1320420-2 and Adapter
Kit 856046-1 for Use with
Side-Feed Stripper-
Crimper II No. 1320895-2
409-5253 — AMP-TAPEMATIC
4/8 Indent Stripper
Terminator Model 3
Part No. 599406-5, -6
and -7
Catalog
82275 — Crimp Quality Monitor
(CQM)
www.amp.com/tooling
Stripper-Crimper Machines
(AMP-O-MATIC and AMP-TAPEMATIC 4/8 Indent)
This semiautomatic bench
machine strips and terminates
wire in a single operation.
You simply position the
wire against a spot illuminated
on the wire stop and
cycle the machine. In the
automatic mode, the
machine cycles when the
wire touches the wire stop.
Using interchangeable
applicators, this versatile
machine is ideal for terminating
jacketed cable with a
variety of pin and socket
contacts including
AMPLIMITE Subminiature D,
MATE-N-LOK and Multimate
Type III+. Applicators are
also available for non-AMP
products. The minimum
wire breakout (wire length
that must be exposed) is
only .72 [18].
In addition to the use of
quick-change applicators,
machine adjustments have
been simplified to reduce
set-up times. Strip blades
are keyed for ease of alignment;
strip length and cutting
depth are easily adjusted
from the front of the
machine without special
tools. To compensate for
variations in feed points of
different terminal strips, simply
turn an adjustment knob.
For highly accurate, realtime
monitoring of every
crimp, the Stripper-Crimper
can be equipped with crimp
quality monitoring (CQM).
It’s the only system available
that checks crimp height as
well as the crimp force
curve. It also provides visual
and audible alerts of questionable
crimps, plus ports
for printing and networking.
And, to maintain tight crimp
tolerances, the Stripper-
Crimper allows you to adjust
crimp height in .0005
[0.0127] increments.
For drawings or technical data, contact your Tyco Electronics sales engineer or call the Technical Support Center: 1-800-522-6752.
Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents.
Specifications subject to change. Consult Tyco Electronics for latest specifications.
Catalog
65004
Revised 01-01
Other features include a
convenient scrap removal
system consisting of a disposal
chute and collection
tray, and a lock-out/tag-out
device to prevent accidentally
restoring air to the
machine during maintenance
and repair.
Need more information?
For information specifically
about tooling, call the
Technical Support Center
at 1-800-522-6752.
©1992, 1997 and 2000 by Tyco
Electronics Corporation.
All Rights Reserved.
AMP, AMPLIMITE, AMP-O-MATIC,
AMP-TAPEMATIC, MATE-N-LOK and
TYCO are trademarks.
1

2
Specifications —
Stripper-Crimper
Width — 14 [355]
Depth — 18.7 [475]
Height — 20 [500] without reel
Weight — 150 lb [68 kg]
Air — 80-100 psi [5.52-6.90 bar],
3.5 scfm [.00165 m 3 /s]
Electrical — 120/240 VAC, 50/60 Hz
Specifications — CQM
Electrical — 100-120 VAC, 50 or
60 Hz, .5 A; 200-240 VAC, 50 Hz, .25 A
Specifications
Width—12.5 [317]
Depth—12.5 [317]
Height—10 [254] without reel
Weight—45 lb [20 kg]
Electrical—120 VAC, 60 Hz, 1.3 A
Wire Range—28-20 AWG
[0.08-0.5 mm 2 ]
65004—5M—GATD—01-01—015
Printed in U.S.A.
Stripper-Crimper Machines
(AMP-O-MATIC and AMP-TAPEMATIC 4/8 Indent)
AMP-O-MATIC Stripper-Crimper Machine Dimensions
Part Number Description
1320895-1 Stripper-Crimper
1320895-2 Stripper-Crimper with Crimp Quality Monitor (CQM) Attachment Kit
1320420-2 CQM* (Monitor Only) Domestic: 120 VAC, 50 or 60 Hz
856046-1 CQM Attachment Kit (Includes Mounting Bracket, Cabling and Hardware)
856046-2 CQM* (Domestic Monitor) and CQM Attachment Kit
* Requires CQM applicators; call the Technical Support Center for further information.
When needed, you may upgrade Part No. 1320895-1 to CQM capability by ordering Part No. 856046-2 or
Part No. 856046-1 plus Part No. 1320420-2.
AMP-TAPEMATIC 4/8 Indent Stripper-Crimper Machine
Part Number 599406-7
30
[760]
14
[355]
Portable bench machine
that strips wire and crimps
tape-mounted, closedbarrel
pin and socket contacts
for AMPLIMITE
Military, ARINC and CPC
connectors. The stripping
and crimping heads are
accessible through separate
openings in the front of
the machine. Wire strip
length and crimp height are
adjustable. The stripping
head is pre-set to the proper
cutting depth of four
standard wire sizes.
Wire funnels are ordered
separately. A different funnel
is required for each contact
size. Call the Technical
Support Center for further
information.
Printed on recycled paper. Tyco Electronics Corporation, Harrisburg, PA 17105; Phone: 717-564-0100; Technical Support Center Fax: 717-986-3316; Internet: www.amp.com
For drawings or technical data, contact your Tyco Electronics sales engineer or call the Technical Support Center: 1-800-522-6752.
Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents.
Specifications subject to change. Consult Tyco Electronics for latest specifications.
20
[500]
18.7
[475]
Front View Side View
Catalog
65004
Revised 01-01