New Rulon Catalog

More documents

Recommendations

Info

RULON ®XLRULON ®XL/Rulon® XL is a tan colored material that is bestfor use against aluminum (including anodized)substrates. Rulon® XL exhibits very low wearas compared with other Rulon® grades.Other advantages offered by this uniquematerial are that it combines low deformationunder load with exceptionally good chemicalresistance.It is compatible with a wide range of matingsurfaces, but is not recommended for use withalkalis. Its non-abrasive character enhancesthe frictional performance to prevent gallingof softer mating surfaces.It is the best material for vacuum service.Design CriteriaRulon XLTypical Product andApplication DescriptionProducts• Automatically moldedbearings & components• Sleeve, flanged andthrust bearings• Piston Rings• Stamped and formedseals• Extruded shapes• Machined parts• Molded shapesApplications• Vacuum Pumps• Mixers• Compressors• Appliances• Automotive• Insulators• Linear slides• Shaft support• Wear bandsTemperature - Typical Range ˚FMaximum PV (continuous)(MPa•m/s)Maximum P - psi (static)(MPa)Maximum V -SFM (no load)(m/s)Shaft Hardness - MinimumShaft finish recommended Ra (µ”/µm)Shaft MaterialEngineering InformationFriction - static & dynamicWater Absorption ASTM D570Flammability ASTM D635Chemical ResistanceThermal ConductivityBTU/hr/sq. ft./˚F/in.Linear Coefficient of (78˚-200˚F)Thermal Expansion (26˚ -93˚C)Physical DataElongation ASTM D638Tensile Strength ASTM D638(MPa)Deformation (1500 psi - 24 hr. RT)Specific Gravity-400/+550 (-240/288)10,000 (0.35)*1,200 (8.3)*400 (2)*Rb258 - 16 (0.2-0.4)*All Steels andaluminum.10 - .250%Non-FlammableInert1.7Diameter 6.4x10 -5 (11.5)*160%1700 psi (11.7)*1.4%1.97A more complete data sheet is available upon request.*Metric measurements in parentheses11
RULON ®/ RULON ® FFRulon® F is a green material with excellentinsulating properties and superior abrasionresistance.It is used in a wide variety of wearcomponent and bearing applications, and iscurrently used as the liner in one of ourcomposite journal bearings (Rulon® FCJ).Rulon® F exhibits excellent wear resistance,especially in dry conditions. This materialsuitably slides against a wide range ofmating surfaces but is not recommended forcontact with strong bases or steam.Design CriteriaRulon FTemperature - Typical Range ˚F (˚C)Maximum PV (continuous)(MPa•m/s)Maximum P - psi (static)(MPa)Maximum V -SFM (no load)(m/s)Shaft Hardness - MinimumShaft finish recommended Ra (µ”/µm)Shaft MaterialEngineering InformationFriction - static & dynamicFlammability ASTM D635Chemical ResistanceThermal ConductivityBTU/hr/sq. ft./˚F/in.Linear Coefficient ofThermal ExpansionPhysical Data(78˚-200˚F)(26˚ -93˚C)(78˚-300˚F)(26˚-149˚C)Elongation ASTM D638Tensile Strength ASTM D638(MPa)Deformation (1500 psi - 24 hr. RT)Specific Gravity-400/+550 (-240/288)10,000 (0.35)*1,000 (6.9)*400 (2)*Rb258 - 16 (0.2-0.4)*Stainless andHardened Steel.12 - .20Non-FlammableData AvailableA more complete data sheet is available upon request.*Metric measurements in parentheses2.6Diameter 3.5x10 -5 (6.3)*Length 6.2x10 -5 (11.2)*Diameter 3.6x10 -5 (6.4)*Length 7.0x10 -5 (12.6)*160%1200 psi (8.3)*3%1.89Typical Product andApplication DescriptionProducts• Automatically moldedbearings & components• Sleeve, flanged andthrust bearings• Piston Rings• Stamped and formedseals• Extruded shapes• Machined parts• Molded shapesApplications• Clothes Dryers• Chute Liners• Compressors• Appliances• Automotive• Insulators• Linear slides• Pipe supports• Wear bands12
Page 1 and 2: High PerformanceFluoropolymerMateri
Page 3 and 4: ProductsBearings:Sleeve, flanged, a
Page 5 and 6: RULON ® LR ® LRRulon® LR is a ma
Page 7 and 8: RULON ® 641 ® 641Rulon® 641 is m
Page 9 and 10: RULON ® 123 ® 123Rulon® 123 is a
Page 11: RULON ® 957 ® 957Rulon® 957 is a
Page 15 and 16: RULON ® 945 ® 945Rulon® 945 is a
Page 17 and 18: RULO1337RULON ® Rulon® 1337 is a
Page 19 and 20: RULON ® 1439 ® 1439Rulon® 1439 i

New Rulon Catalog

Create successful ePaper yourself

Delete template?

Save as template?