ZT 6301

ZT 6301Hot-Swap AC Power SupplyRemote SenseA common remote sense on the +3.3V and +5V power supply outputs will detect the voltage ata load remote from the power supply, compensating for connector, backplane and wiring voltagedrops. The 3S+ and 5S+ signals should be connected to the proper load. The ZT 5610 uses an21152 PCI-to-PCI bridge to generate the local onboard PCI bus. This ensures that only one loadis presented to the CompactPCI bus, meeting the requirements of the specification. ActivityLEDs on the board indicate traffic on the local "PMC" bus for diagnostic purposes.Inhibit/Enable InputsThe INH# input signal on the rear connector willturn off the outputs when grounded. The enable(EN#) input must always be connected to ground.System NotificationTwo fault outputs are available on the rearconnector for system notification. One output(DEG#) is an open collector, low true signal thatindicates the internal temperature is approaching90 C. If action does not reverse the internaltemperature rise, at 100 C the supply will shut offthe outputs. The second output (FAL#) is anopen collector, low true signal that indicates thatthe supply has a problem or the input voltage hasbeen removed.WarrantyOne yearFigure 1. Close Up ViewsContact InformationPerformance Technologies205 Indigo Creek Dr.Rochester, NY 14626Tel: 585-256-0200Fax: 585-256-0791E-mail: sales@pt.comOutputLoad (W)1601401201009080Forced Air @ 15cfmFigure 2. Output DeratingCurves For Various AirFlows604020www.pt.com10 20 30 40 5060 70Ambient Temperature (C)© 2004 Performance Technologies. All rights reserved.

ZT 6301Hot-Swap AC Power SupplyPin # (1) Staging (2) Mnemonic DescriptionFigure 3. Pin NumbersColumn AA13A14A15A16A17A18A19A20ELELELELELELELELSPINH#ISHS-5S+3.3S++12V-12VSpare (do not connect)Inhibit SignalCurrent Share SignalSense -5V Sense ++3.3V Sense+12 VDC-12 VDCColumn BB2B5B8B11B13–18B19B20B22B25B28B31SLSL–ELSLSLSLELEL––ACLACN–CG (3)3.3V+12V-12V5VGND––AC LineAC NeutralNo Pin LoadedChassis Ground+3.3 VDC+12 VDC-12 VDC+5 VDCGroundNo Pin LoadedNo Pin LoadedB25Column CC13C14C15C16–18C19C20SLSLSLSLSLSLEN#DEG#FAL#3.3V+12V-12VEnable SignalTemp. Warning SignalSupply Fail Signal+3.3 VDC+12 VDC-12 VDC13811ACContact InformationPerformance Technologies205 Indigo Creek Dr.Rochester, NY 1462620Tel: 585-256-0200Fax: 585-256-079122E-mail: sales@pt.comFigure 4. Mating Connector (top view)25Pin numbers illustrated are the pin view of the female mating connector.A mating connector is ERNI part #914374; AMP #148370-1 or#97-7200-016.28www.pt.comNotes:(1) Mating pin numbers on power supply connector.(2) EL is an Extra Length pin. SL is a Standard Length pin.(3) CG must be connected to earth ground.31© 2004 Performance Technologies. All rights reserved.

ZT 6301Hot-Swap AC Power Supply>>Ordering InformationTo discuss your specificrequirements and/orpricing, please contactsales@pt.com.Custom configuration optionsmay be available.Contact InformationPerformance Technologies205 Indigo Creek Dr.Rochester, NY 14626Tel: 585-256-0200Fax: 585-256-0791E-mail: sales@pt.comwww.pt.comSpecificationsThe ZT 6301 is compliant with the followingspecification:• CompactPCI® core specification, PICMG 2.0,R2.1Electrical• Input Voltage Range: 90-254VAC• Input Filter Type: Common and Differentialmode• Input Frequency Range AC: 47 to 63HzNote: Always connect chassis ground (CG) on thesupply to earth ground through a low impedancepath.Environmental• Operating Temperature: 0 to 70 C• Storage Temperature: -40 to +85 C• Non-Condensing Relative Humidity: less than95% at 40 CInput Current• Maximum Continuous: 2.2A @ 115VAC• Single Cycle, Surge Maximum: .99Output SpecificationsTotal Voltage Accuracy (load, cross and lineregulation across temperature):+3.3V* @ 20A ±2%+5V @ 25A (2A minimum)* ±2%+12V @ 5.5A ±2%-12V @ 0.5A ±4%*Combined current not to exceed 25A.Total Output Power (max. continuous @ 30 C):150WRipple and Noise(measured at full load with 20 MHz bandwidthand 22 µF capacitor at load, or 50mV, whicheveris greater):+3.3V