Twose Rotary Tedder (RT555) - Early Models (Flat Tine Arms)

More documents

Recommendations

Info

Publication 53020406TECHNICAL DATAType <strong>Tedder</strong> 555Number of rotors 4Diameter of rotor1,75 mNo. of tines/rotor 6Angle of tines14-18 DegreesWorking capacity5,5 ha/hWorking width5,3 mTransport width2,95 mWidth of the machine5,72 mHeight2,7 mLength2,0 mWorking speed up to12 km/hWeight475 kgNecessary tractor power15 kW/20PSRevolutions on PTO shaft450-540 U/minNo. of revolutions on rotorsat 540 RPM on PTO shaft175 RPMTyres15x6.00-6FrameadjustableHitch frame 3 point flexiblePull typeLifting to transport positionby hand operated hydraulic systemPTO Shaft:length between the joints(for pull type hitch)1350 mm1350 mmSafety coupling900 Nmworking snap300 NmMACHINE RECORD PLATEInformation on the plate includes Machine Type, Serial Number and Weight. The machine type and serialnumber must always be quoted in all correspondence and when ordering spare parts.Page 4
Publication 53020406DESCRIPTIONThe 555 rotary tedder is designed for forage tedding and spreading. It works on the principle of rotating springtines attached the rotors. Four forward angled rotors contra-rotate against each other, therefore the springtines gently rake and collect the forage in the front and put it turned gently down behind the tedder. Gentle,airy and completely even scattering and tedding essentially accelerates drying and reduces losses whichappear as a result of plant crumbling. You have so reduced the drying time and became less dependant ongood weather and preserved valuable nourishing substances.The tedder is constructed so that each rotor adjusts over the support wheel to the surface. Therefore thetedder collects the forage cleanly and consistently in spite of its large working width. The tedder worksdisturbance free on leaned and rough surfaces as well. The spring tines are made of high quality steel andfixed in such a manner, to enable spring flexibility.The tedder can be connected to any type of tractor, which has a three point connection system and a hydraulicconnection. It is driven by a cardan P.T.O. shaft.Setting the tedder into working or transport position is a simple and fast operation with a help of hydrauliccylinders, operable from the tractor cab. Work with the tedder is simple, clear and safe.GENERAL ARRANGEMENT1. Side rotor2. Spring tine arm3. Spring tine4. Support wheel5. Jack stand6. Protection rail7. Protection of the P.T.O. shaft8. Hydraulic tube9. Hydraulic cylinder10. Rotor hold/for transport position11. Pull rope12. Gear joint13. Lifting and lowering speed adjusting screwPage 5
Page 1 and 2: ROTARYTEDDER555INSTRUCTION MANUAL&
Page 3: Publication 53020406List of Content
Page 7 and 8: Publication 53020406SAFETYWhen work
Page 9 and 10: Publication 53020406Fig. 3In case t
Page 11 and 12: Publication 53020406Fig. 68. Contro
Page 13 and 14: Publication 53020406ReplacementPart
Page 15 and 16: Publication 53020406REF. QTY. PART
Page 19 and 20: Publication 53020406MAIN FRAMEREF.
Page 21 and 22: Publication 53020406WHEEL ASSEMBLYR
Page 23 and 24: Publication 53020406TUBE ASSEMBLYRE
Page 27 and 28: Publication 53020406WHEEL ASSEMBLYR
Page 29 and 30: Publication 53020406GUARDINGREF. QT

Twose Rotary Tedder (RT555) - Early Models (Flat Tine Arms)

Create successful ePaper yourself

Delete template?

Save as template?