Turn-only hardware Tilt and turn hardware
Turn-only hardware Tilt and turn hardware
Turn-only hardware Tilt and turn hardware
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
<strong>Turn</strong>-<strong>only</strong> <strong>hardware</strong><strong>and</strong><strong>Tilt</strong> <strong>and</strong> <strong>turn</strong> <strong>hardware</strong>Quality assuranceRAL-GZ 607/3February 2009
RAL-GZ 607/3 Version February 2009PrefaceThe quality assurance of <strong>turn</strong>-<strong>only</strong> <strong>hardware</strong> <strong>and</strong> tilt <strong>and</strong> <strong>turn</strong> <strong>hardware</strong> has been a voluntarycommitment to the quality <strong>and</strong> further development of these fittings products since 1983. Thisis proven <strong>and</strong> demonstrated by the familiar quality mark. The quality <strong>and</strong> test procedureshave been the st<strong>and</strong>ard for functioning, lasting <strong>and</strong> reliable <strong>turn</strong>-<strong>only</strong> <strong>hardware</strong> <strong>and</strong> tilt <strong>and</strong><strong>turn</strong> <strong>hardware</strong> since this time.The revised quality <strong>and</strong> test procedures in RAL-RG 607/3 take particular note of theEuropean st<strong>and</strong>ards on windows <strong>and</strong> doors (EN 1191) <strong>and</strong> the corresponding fittings (EN13126-8) that have now been published. These are the main basis.These voluntary quality <strong>and</strong> test procedures go beyond the predefinition of the basicEuropean st<strong>and</strong>ards with additional quality requirements <strong>and</strong> should further highlight theparticular quality of the <strong>turn</strong>-<strong>only</strong> <strong>hardware</strong> <strong>and</strong> tilt <strong>and</strong> <strong>turn</strong> <strong>hardware</strong>. The RAL quality markcan thus <strong>only</strong> be achieved by a manufacturer who meets the quality requirements set herefrom the design through to the production.The requirements included in these quality <strong>and</strong> test procedures essentially applyindependent of any materials.These new quality <strong>and</strong> test procedure replace the following regulation:RAL-RG 607/3 (1995-02)<strong>Turn</strong>-<strong>only</strong> <strong>hardware</strong> <strong>and</strong> tilt <strong>and</strong> <strong>turn</strong> <strong>hardware</strong>The Gütegemeinschaft Schlösser und Beschläge e.V. thus creates the preconditions for thesuccessful continuation of the RAL quality assurance of <strong>turn</strong>-<strong>only</strong> <strong>hardware</strong> <strong>and</strong> tilt <strong>and</strong> <strong>turn</strong><strong>hardware</strong>.GütegemeinschaftSchlösser und Beschläge e.V.Offerstraße 1242551 VelbertFon: +49 (0)2051 / 95 06 – 5Fax: +49 (0)2051 / 95 06 – 69Home: www.piv-velbert.deGütegemeinschaft Schlösser und Beschläge e.V. Page 2 / 18
RAL-GZ 607/3 Version February 2009Content1 Scope..............................................................................................................................42 Fundamentals of quality assurance .................................................................................42.1 Basics ......................................................................................................................42.2 Elements of the proof of suitability............................................................................43 Initial testing, quality mark ...............................................................................................53.1 Initial testing.............................................................................................................53.2 Quality mark.............................................................................................................54 Initial visit ........................................................................................................................55 Supervision .....................................................................................................................65.1 Self monitoring – in-house production control ..........................................................65.1.1 General remarks...........................................................................................65.1.2 Incoming goods inspection ...........................................................................65.1.3 Production control ........................................................................................65.1.4 Testing the marking......................................................................................75.1.5 Overview of self monitoring ..........................................................................75.2 External control – regular test ..................................................................................85.2.1 Interval <strong>and</strong> content......................................................................................85.2.2 Sampling ......................................................................................................85.2.3 Supervision report ........................................................................................85.2.4 Rectification of defects – special test............................................................85.2.5 Deadline for the rectification of defects.........................................................95.3 Repeat test – validity of the quality mark.................................................................96 Marking with the quality mark ..........................................................................................96.1 Marking of <strong>turn</strong>-<strong>only</strong> <strong>hardware</strong> <strong>and</strong> tilt <strong>and</strong> <strong>turn</strong> opening fittings................................96.2 Using the quality mark..............................................................................................97 Changes..........................................................................................................................9Gütegemeinschaft Schlösser und Beschläge e.V. Page 3 / 18