Vishay TSSP77038 IR receiver module datasheet - Pololu Robotics ...

More documents

Recommendations

Info

www.vishay.comREEL DIMENSIONS in millimetersNew ProductTSSP77038Vishay Semiconductors16734LEADER AND TRAILER DIMENSIONS in millimetersTrailerno devicesdevicesLeaderno devicesEndStartmin. 200 min. 40096 11818COVER TAPE REEL STRENGTHAccording to DIN EN 60286-30.1 N to 1.3 N300 ± 10 mm/min.165° to 180° peel angleLABELStandard bar code labels for finished goodsThe standard bar code labels are product labels and usedfor identification of goods. The finished goods are packed infinal packing area. The standard packing units are labeledwith standard bar code labels before transported as finishedgoods to warehouses. The labels are on each packing unitand contain Vishay Semiconductor GmbH specific data.Rev. 1.0, 09-Mar-12 8 Document Number: 82470THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
www.vishay.comNew ProductTSSP77038Vishay SemiconductorsVISHAY SEMICONDUCTORS GmbH STANDARD BAR CODE PRODUCT LABEL (finished goods)PLAIN WRITING ABBREVIATION LENGTHItem-description - 18Item-number INO 8Selection-code SEL 3LOT-/serial-number BATCH 10Data-code COD 3 (YWW)Plant-code PTC 2Quantity QTY 8Accepted by ACC -Packed by PCK -Mixed code indicator MIXED CODE -Origin xxxxxxx+ Company logoLONG BAR CODE TOP TYPE LENGTHItem-number N 8Plant-code N 2Sequence-number X 3Quantity N 8Total length - 21SHORT BAR CODE BOTTOM TYPE LENGTHSelection-code X 3Data-code N 3Batch-number X 10Filter - 1Total length - 17DRY PACKINGThe reel is packed in an anti-humidity bag to protect thedevices from absorbing moisture during transportation andstorage.15973Aluminum bagReelLabelFINAL PACKINGThe sealed reel is packed into a cardboard box. A secondarycardboard box is used for shipping purposes.RECOMMENDED METHOD OF STORAGEDry box storage is recommended as soon as the aluminumbag has been opened to prevent moisture absorption. Thefollowing conditions should be observed, if dry boxes arenot available:• Storage temperature 10 °C to 30 °C• Storage humidity ≤ 60 % RH max.After more than 72 h under these conditions moisturecontent will be too high for reflow soldering.In case of moisture absorption, the devices will recover tothe former condition by drying under the following condition:192 h at 40 °C + 5 °C/- 0 °C and < 5 % RH (dry air/nitrogen)or96 h at 60 °C + 5 °C and < 5 % RH for all device containersor24 h at 125 °C + 5 °C not suitable for reel or tubes.An EIA JEDEC standard JSTD-020 level 4 label is includedon all dry bags.CAUTIONThis bag containsMOISTURE-SENSITIVE DEVICES1. Shelf life in sealed bag: 12 months at < 40 °C and < 90 % relativehumidity (RH)2. After this bag is opened, devices that will be subjected to solderingreflow or equivalent processing (peak package body temp. 260 °C)must be2a. Mounted within 72 hours at factory condition of < 30 °C/60 % RH or2b. Stored at < 5 % RH3. Devices require baking befor mounting if:Humidity Indicator Card is > 10 % when read at 23 °C ± 5 °C or2a. or 2b. are not met.4. If baking is required, devices may be baked for:192 hours at 40 °C + 5 °C/- 0 °C and < 5 % RH (dry air/nitrogen) or96 hours at 60 °C ± 5 °C and < 5 % RH for all device containers or24 hours at 125 °C ± 5 °C not suitable for reels or tubesBag Seal Date:(If blank, see barcode label)Note: Level and body temperature defined by EIA JEDEC Standard JSTD-02022522LEVEL4EIA JEDEC standard JSTD-020 level 4 label is includedon all dry bagsRev. 1.0, 09-Mar-12 9 Document Number: 82470THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Page 1 and 2: www.vishay.comNew ProductTSSP77038V
Page 3: www.vishay.comNew ProductTSSP77038V
Page 7: New Productwww.vishay.comTSSP77038V
Page 11: www.vishay.comLegal Disclaimer Noti

Vishay TSSP77038 IR receiver module datasheet - Pololu Robotics ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?