Vishay TSSP77038 IR receiver module datasheet - Pololu Robotics ...

www.vishay.comNew ProductTSSP77038Vishay SemiconductorsIR Receiver Modules for Remote Control Systems432120953MECHANICAL DATAPinning:1, 4 = GND, 2 = V S , 3 = OUTFEATURES• Very low supply current• Photo detector and preamplifier in one package• Internal filter for 38 kHz IR signals• Supply voltage: 2.5 V to 5.5 V• Improved immunity against ambient light• Capable of side or top view• Insensitive to supply voltage ripple and noise• Two lenses for high sensitivity and wide receiving angle• Narrow optical filter to reduce interference from plasmaTV emissions• Material categorization: For definitions of complianceplease see www.vishay.com/doc?99912DESCRIPTIONThe TSSP77038 is a compact two lens SMD IR receiverfor sensor applications. It has a high gain for IR signalsat 38 kHz. The detection level does not change whenambient light or strong IR signals are applied. It can receivecontinuous 38 kHz signals or 38 kHz bursts.This component has not been qualified according toautomotive specifications.PARTS TABLECARRIER FREQUENCYSENSOR APPLICATIONS38 kHz TSSP77038BLOCK DIAGRAMAPPLICATION CIRCUITInputAMPDemo-dulatorBandpass33 kΩ2V S3OUT1, 417170-10TransmitterwithTSALxxxxIR receiverCircuitV SOUTGNDR 1C 1V OµC+ V SGNDPIN16833_17GNDThe external components R 1 and C 1 are optionalto improve the robustness against electrical overstress(typical values are R 1 = 100 Ω, C 1 = 0.1 µF).Rev. 1.0, 09-Mar-12 1 Document Number: 82470THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

www.vishay.comNew ProductTSSP77038Vishay SemiconductorsABSOLUTE MAXIMUM RATINGSPARAMETER TEST CONDITION SYMBOL VALUE UNITSupply voltage V S - 0.3 to + 6 VSupply current I S 5 mAOutput voltage V O - 0.3 to (V S + 0.3) VOutput current I O 5 mAJunction temperature T j 100 °CStorage temperature range T stg - 25 to + 85 °COperating temperature range T amb - 25 to + 85 °CPower consumption T amb ≤ 85 °C P tot 10 mWNote• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating onlyand functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specificationis not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability.ELECTRICAL AND OPTICAL CHARACTERISTICS (T amb = 25 °C, unless otherwise specified)PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNITSupply voltage V S 2.5 5.5 VSupply currentTransmission distanceOutput voltage lowMinimum irradianceMaximum irradianceDirectivityV S = 5 V, E v = 0 I SD 0.55 0.7 0.9 mAE v = 40 klx, sunlight I SH 0.8 mAE v = 0,IR diode TSAL6200,I F = 250 mA,test signal see fig. 1I OSL = 0.5 mA, E e = 0.7 mW/m 2 ,test signal see fig. 1Pulse width tolerance:t pi - 5/f o < t po < t pi + 6/f o,test signal see fig. 1t pi - 5/f o < t po < t pi + 6/f o ,test signal see fig. 1Angle of half transmissiondistanced 40 mV OSL 100 mVE e min. 0.2 0.4 mW/m 2E e max. 50 W/m 2ϕ 1/2 ± 50 degTYPICAL CHARACTERISTICS (T amb = 25 °C, unless otherwise specified)E eV OV OHOptical Test Signal1.5(IR diode TSAL6200, I F = 0.4 A, 30 pulses, f = f 0 , t = 10 ms)1.41.31.21.1t1.00.9t pi *0.80.7T0.6* t pi 10/f 0 is recommended for optimal function0.5Output Signal161100.40.31) 7/f 0 < t d < 15/f 00.22) t pi - 5/f 0 < t po < t pi + 6/f 00.10t po - Output Pulse Width (ms)Output pulse widthInput burst lengthλ = 950 nm,optical test signal, Fig. 1V OLt d1) t po2)t0.1 10 1000 100 000E e - Irradiance (mW/m 2 )Fig. 1 - Output Active Low Fig. 2 - Pulse Length and Sensitivity in Dark AmbientRev. 1.0, 09-Mar-12 2 Document Number: 82470THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

www.vishay.comNew ProductTSSP77038Vishay SemiconductorsE eV OV OHV OLOptical Test Signal600 µs 600 µstt = 60 msOutput Signal, (see fig. 4)94 8134t on t offtE e min. - Threshold Irradiance (mW/m 2 )5.04.54.03.53.02.52.01.51.00.5Correlation with Ambient Light Sources:10 W/m 2 = 1.4 kLx (Std. illum. A, T = 2855 K)10 W/m 2 = 8.2 kLx (Daylight, T = 5900 K)Wavelength of AmbientIllumination: λ = 950 nm00.01 0.1 1 10 100E e - Ambient DC Irradiance (W/m 2 )Fig. 3 - Output FunctionFig. 6 - Sensitivity vs. Supply Voltage Disturbancest on , t off - Output Pulse Width (ms)0.80.70.60.50.40.30.2t ont off0.1 λ = 950 nm,optical test signal, Fig. 300.1 1 10 100 1000 10 000E e - Irradiance (mW/m 2 )E e min. - Sensitivity (mW/m 2 )0.400.350.300.250.200.150.100.050- 30 - 10 10 30 50 70 90T amb - Ambient Temperature (°C)Fig. 4 - Output Pulse DiagramFig. 7 - Sensitivity vs. Ambient TemperatureE e min. /E e - Rel. Responsivity169251.21.00.80.60.40.20.0f = f 0± 5 %Δ f(3 dB) = f 0/100.7 0.9 1.1 1.3f/f 0 - Relative FrequencyS (λ) rel- Relative Spectral Sensitivity10.90.80.70.60.50.40.30.20.10750 800 850 900 950 1000 1050 1100 115021425 λ- Wavelength (nm)Fig. 5 - Frequency Dependence of ResponsivityFig. 8 - Relative Spectral Sensitivity vs. WavelengthRev. 1.0, 09-Mar-12 3 Document Number: 82470THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

www.vishay.comNew ProductTSSP77038Vishay SemiconductorsVISHAY LEAD (Pb)-FREE REFLOW SOLDER PROFILET (°C)300max. 260 °C250 255 °C240 °C 245 °C217 °C200max. 20 s150max. 120 s max. 100 s10050max. Ramp Up 3 °C/smax. Ramp Down 6 °C/s00 50 100 150 200 250 30019800t (s)max. 2 cycles allowedTAPING VERSION TSSP..TR DIMENSIONS in millimeters4 °7.1167.51.75822.83.30.34 °1.34 ref.Ø 1.5Ø 1.5 minDirection of feed4technical drawingsaccording to DINspecificationsDrawing-No.: 9.700-5337.01-4Issue: 1; 16.10.0821577Rev. 1.0, 09-Mar-12 6 Document Number: 82470THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

New Productwww.vishay.comTSSP77038Vishay SemiconductorsTAPING VERSION TSSP..TT DIMENSIONS in millimeters4°7.13.35161.75 7.54823.3Ø 1.5Ø 1.5 min.Direction of feed0.34°Drawing-No.: 9.700-5338.01-4Issue: 3; 09.06.0921578technical drawingsaccording to DINspecificationsRev. 1.0, 09-Mar-12 7 Document Number: 82470THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

www.vishay.comREEL DIMENSIONS in millimetersNew ProductTSSP77038Vishay Semiconductors16734LEADER AND TRAILER DIMENSIONS in millimetersTrailerno devicesdevicesLeaderno devicesEndStartmin. 200 min. 40096 11818COVER TAPE REEL STRENGTHAccording to DIN EN 60286-30.1 N to 1.3 N300 ± 10 mm/min.165° to 180° peel angleLABELStandard bar code labels for finished goodsThe standard bar code labels are product labels and usedfor identification of goods. The finished goods are packed infinal packing area. The standard packing units are labeledwith standard bar code labels before transported as finishedgoods to warehouses. The labels are on each packing unitand contain Vishay Semiconductor GmbH specific data.Rev. 1.0, 09-Mar-12 8 Document Number: 82470THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

www.vishay.comNew ProductTSSP77038Vishay SemiconductorsVISHAY SEMICONDUCTORS GmbH STANDARD BAR CODE PRODUCT LABEL (finished goods)PLAIN WRITING ABBREVIATION LENGTHItem-description - 18Item-number INO 8Selection-code SEL 3LOT-/serial-number BATCH 10Data-code COD 3 (YWW)Plant-code PTC 2Quantity QTY 8Accepted by ACC -Packed by PCK -Mixed code indicator MIXED CODE -Origin xxxxxxx+ Company logoLONG BAR CODE TOP TYPE LENGTHItem-number N 8Plant-code N 2Sequence-number X 3Quantity N 8Total length - 21SHORT BAR CODE BOTTOM TYPE LENGTHSelection-code X 3Data-code N 3Batch-number X 10Filter - 1Total length - 17DRY PACKINGThe reel is packed in an anti-humidity bag to protect thedevices from absorbing moisture during transportation andstorage.15973Aluminum bagReelLabelFINAL PACKINGThe sealed reel is packed into a cardboard box. A secondarycardboard box is used for shipping purposes.RECOMMENDED METHOD OF STORAGEDry box storage is recommended as soon as the aluminumbag has been opened to prevent moisture absorption. Thefollowing conditions should be observed, if dry boxes arenot available:• Storage temperature 10 °C to 30 °C• Storage humidity ≤ 60 % RH max.After more than 72 h under these conditions moisturecontent will be too high for reflow soldering.In case of moisture absorption, the devices will recover tothe former condition by drying under the following condition:192 h at 40 °C + 5 °C/- 0 °C and < 5 % RH (dry air/nitrogen)or96 h at 60 °C + 5 °C and < 5 % RH for all device containersor24 h at 125 °C + 5 °C not suitable for reel or tubes.An EIA JEDEC standard JSTD-020 level 4 label is includedon all dry bags.CAUTIONThis bag containsMOISTURE-SENSITIVE DEVICES1. Shelf life in sealed bag: 12 months at < 40 °C and < 90 % relativehumidity (RH)2. After this bag is opened, devices that will be subjected to solderingreflow or equivalent processing (peak package body temp. 260 °C)must be2a. Mounted within 72 hours at factory condition of < 30 °C/60 % RH or2b. Stored at < 5 % RH3. Devices require baking befor mounting if:Humidity Indicator Card is > 10 % when read at 23 °C ± 5 °C or2a. or 2b. are not met.4. If baking is required, devices may be baked for:192 hours at 40 °C + 5 °C/- 0 °C and < 5 % RH (dry air/nitrogen) or96 hours at 60 °C ± 5 °C and < 5 % RH for all device containers or24 hours at 125 °C ± 5 °C not suitable for reels or tubesBag Seal Date:(If blank, see barcode label)Note: Level and body temperature defined by EIA JEDEC Standard JSTD-02022522LEVEL4EIA JEDEC standard JSTD-020 level 4 label is includedon all dry bagsRev. 1.0, 09-Mar-12 9 Document Number: 82470THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

www.vishay.comNew ProductTSSP77038Vishay SemiconductorsESD PRECAUTIONProper storage and handling procedures should be followedto prevent ESD damage to the devices especially when theyare removed from the antistatic shielding bag. Electro-staticsensitive devices warning labels are on the packaging.VISHAY SEMICONDUCTORS STANDARD BARCODE LABELS (example)The Vishay Semiconductors standard bar code labels areprinted at final packing areas. The labels are on eachpacking unit and contain Vishay Semiconductors specificdata.22178Rev. 1.0, 09-Mar-12 10 Document Number: 82470THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

www.vishay.comLegal Disclaimer NoticeVishayDisclaimerALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVERELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any otherdisclosure relating to any product.Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose orthe continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and allliability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particularpurpose, non-infringement and merchantability.Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typicalrequirements that are often placed on Vishay products in generic applications. Such statements are not binding statementsabout the suitability of products for a particular application. It is the customer’s responsibility to validate that a particularproduct with the properties described in the product specification is suitable for use in a particular application. Parametersprovided in datasheets and/or specifications may vary in different applications and performance may vary over time. Alloperating parameters, including typical parameters, must be validated for each customer application by the customer’stechnical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,including but not limited to the warranty expressed therein.Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustainingapplications or for any other application in which the failure of the Vishay product could result in personal injury or death.Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agreeto fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses anddamages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishayor its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel toobtain written terms and conditions regarding products designed for such applications.No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or byany conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.Material Category PolicyVishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill thedefinitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Councilof June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment(EEE) - recast, unless otherwise specified as non-compliant.Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm thatall the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.Revision: 12-Mar-12 1 Document Number: 91000