- Page 1 and 2:
www.smw-autoblok.deJAWS FOR ALLCOMM
- Page 4 and 5:
INCH serration1/16” x 90° or 3/3
- Page 6 and 7:
Hardening instructionfor soft jawsM
- Page 8 and 9:
soft top jawsMWB-DHNbaINCH serratio
- Page 10 and 11:
soft top jaws aluminiumMWB-DA light
- Page 13 and 14:
iReduced jaw mass =Reduced loss of
- Page 15 and 16:
iReduced jaw mass =Reduced loss of
- Page 17 and 18:
Application/customer’s benefit➤
- Page 19 and 20:
Application/customer’s benefit➤
- Page 21 and 22:
soft top jawsWBSA-Dfor SMW-AUTOBLOK
- Page 23 and 24:
soft top jawsfor front end power ch
- Page 25 and 26:
Notessoft top jawsINCH serrationSMW
- Page 27 and 28:
hard top jawsINCH serration1/16”
- Page 29 and 30:
iFor highest accuracy we redommend
- Page 31 and 32:
stop pinsALBType Id-No. G H SWALB 6
- Page 33 and 34:
hard top jawsGFB-DINCH serration1/1
- Page 35 and 36:
hard special jawson customer reques
- Page 37 and 38:
soft top jawssteel ■ aluminiumMET
- Page 39 and 40:
soft top jawsWBJ-M/WBSA-MHNbaMETRIC
- Page 41 and 42:
soft top jawsAWB-Mlong, tipped vers
- Page 43 and 44:
soft pie jaws alum.SBJ-MA light ver
- Page 45 and 46:
soft special jawson customer reques
- Page 47 and 48:
hard top jawsMETRIC serration1,5 x
- Page 49 and 50:
hard roughing jawsSGA-M for externa
- Page 51 and 52:
hard bar roughing jawsGSG-MHbMETRIC
- Page 53 and 54:
hard special jawson customer reques
- Page 55 and 56:
■■T-nutsgrippersSMW-AUTOBLOK Be
- Page 57 and 58:
GHhversion 3NN 1iPlease observe!Alw
- Page 59 and 60:
iPlease observe!Always tighten T-nu
- Page 61 and 62:
GbHhversion 1NiPlease observe!Alway
- Page 63 and 64:
GbGbHhNHhNversion 2 version 3N 1How
- Page 65 and 66:
Datasheet / order formspecial T-nut
- Page 67 and 68:
The economical solution:Roughing ja
- Page 69 and 70:
Precision gripper insertsG14 und G2
- Page 71 and 72:
Precision gripper insertsG30 for hi
- Page 73 and 74: soft top jawssteel ■ aluminiumton
- Page 75 and 76: soft top jawswide versionWAKS for q
- Page 77 and 78: soft pie jawsSBK for quick jaw chan
- Page 79 and 80: soft top jawsWBR for 2- and 3-jaw p
- Page 81 and 82: soft top jawsWAKA2, 3 and 4 jaw ver
- Page 83 and 84: Notessoft top jawstongue & grooveSM
- Page 85 and 86: hard top jawstongue & grooveSMW-AUT
- Page 87 and 88: hard bar roughing jawsGSK for quick
- Page 89 and 90: hard roughing jawsGGK for quick jaw
- Page 91 and 92: hard roughing jawsGGK for quick jaw
- Page 93 and 94: hard roughing jawsGGK for quick jaw
- Page 95 and 96: hard roughing jawsGGK for quick jaw
- Page 97 and 98: hard special jawson customer reques
- Page 99 and 100: jaws forquick jaw change chuckmodul
- Page 101 and 102: hard base jawsGBKS for quick jaw ch
- Page 103 and 104: hard, monoblok roughing jawsGES for
- Page 105 and 106: kombi base jawsKOB for quick jaw ch
- Page 107 and 108: kombi base jawsKLG-M for quick jaw
- Page 109 and 110: soft top jawswide versionWAKS for q
- Page 111 and 112: soft pie jawsSBK for quick jaw chan
- Page 113 and 114: hard, reversible top jawsGUA for qu
- Page 115 and 116: hard roughing jawsGGK for quick jaw
- Page 117 and 118: hard roughing jaws for bar workGSK
- Page 119 and 120: Notesquick jaw changeSystem SMWSMW-
- Page 121 and 122: jaws forquick jaw change chucksmodu
- Page 123: chuck facehard stepped monoblock ja
- Page 127 and 128: soft top jawsWAK for quick jaw chan
- Page 129 and 130: soft top jaws alum.light versionWAK
- Page 131 and 132: soft pie jaws alum.light versionSBK
- Page 133 and 134: hard roughing jaws for bar workGSK
- Page 135 and 136: hard roughing jawsGGK for quick jaw
- Page 137 and 138: hard roughing jawsGGK for quick jaw
- Page 139 and 140: hard roughing jawsGGK for quick jaw
- Page 142 and 143: Monoblock jawswith grippersfor heav
- Page 144 and 145: Hard connecting jawsserration/tongu
- Page 146 and 147: oring ringsADSto bore jaws on the c
- Page 148 and 149: Dress and cleaning plateRPSWith 2 d
- Page 150 and 151: CALCULATION-SERVICEWe can provide a
- Page 152 and 153: Repair ServiceRefurbishing of the c
- Page 154: SMW-AUTOBLOK Spannsysteme GmbHPostf