Shakers

Shakers | AccessoriesIdent. No.2979400AS 1.5 Fastening screwFastening screw for the universal attachmentsAS 130.1, AS 260.1 and the separating funnelattachment AS 260.5. Two AS 1.5 fasteningscrews are required for fastening a clampingroll onto the corresponding basic holder.Ident. No.1269200AS 1.7 Clamping deviceTwo AS 1.6 and two AS 1.7 clamping devices arerequired for fastening two clamping rolls oneabove the other (for clamping separating funnels).For basic holder AS 1.10 only.VG 3.1 Standard attachmentVG 3.31 Test tube attachment*For 54 Eppendorf tubes (continuous operation).Ident. No.3344300VG 3.32 Test tube attachment*VG 3.34 Test tube attachment*For 8 reagent glasses, 16 mm (continuousoperation).MS 3.1 Standard attachmentFor test tubes and small vessels up to Ø 50 mm,included with the minishakers MS 3 basic andMS 3 digital.MS 1.21 One-hand insertFor inserting into the universal attachment,included with the minishakers MS 3 basicand MS 3 digital.MS 1.33 Test tube insertFor inserting into the universal attachment,for 4 test tubes Ø 16 mm.Material: ethylvinyl-acetate.Ident. No.1268400AS 1.6 Fastening screwTwo AS 1.6 clamping devices are required forfastening a clamping roll to the correspondingbasic holder (for basic holder AS 1.10 only).Ident. No.1268900AS 1.8 Supporting clamping deviceTwo AS 1.6 clamping devices and two AS 1.8supporting clamping devices are required if aclamping roll is to be attached at a higher position(e.g. for fixing a vessel which has a higher point ofgravity). For basic holder AS 1.10 only.Standard attachment for reagent glasses / smallvessels (continuous / touch operation), includedwith delivery.Ident. No.3341200For 18 reagent glasses, 10 mm (continuousoperation).Ident. No.3343900Ident. No.3344100VG 3.35 Test tube attachment*For 8 reagent glasses, 20 mm (continuousoperation).Ident. No.3426300MS 3.3 Universal attachmentFor various foam inserts, included with theminishakers MS 3 basic and MS 3 digital.Ident. No.L001540MS 1.31 Test tube insertFor inserting into universal attachment, for 14test tubes Ø 10 mm, material: ethylvinyl-acetate.Ident. No.L001860MS 1.34 Test tube insertFor inserting into the universal attachment,for any number of bore holes. Material:ethylvinyl-acetate.VG 3.2 One-hand attachmentVG 3.33 Test tube attachment*AS 1.12 Supporting barFor attaching two AS 1.13 ground section holdersfor fixing 1000 ml separating funnels. For basicholder AS 1.10 only.Accessories: AS 1.13AS 1.13 Ground section holderFor attaching separating funnels with groundopening NS 29 (2 x AS 1.13 necessary per separatingfunnel). For basic holder AS 1.10 only.One-hand attachment, 88 mm, round, withrubber insert (continuous / touch operation).Ident. No.33423001For 12 reagent glasses, 12 mm (continuousoperation).Ident. No.3344000Ident. No.3344200VG 3.36 Erlenmeyer flask attachment*For 1 Erlenmeyer / round flask from 100 to250 ml (continuous operation).Ident. No.3426600MS 3.4 Microtiter plate attachmentFor use with a microtiter plate, included withthe minishaker MS 3 digital.Ident. No.L001840MS 1.32 Test tube insertFor inserting into the universal attachment, for6 test tubes Ø 12 mm. Material: ethylvinyl-acetate.Included with the minishakers MS 3 digital.Ident. No.L001830VG 3.3 Universal attachmentIdent. No.2594500Length437 mmIdent. No.2597000Universal attachment, 150 mm, withrubber insert (continuous operation).Ident. No.3342100Ident. No.3426400Ident. No.L001850For flask volume AS 2.1AS 2.2AS 2.3AS 2.4AS 2.5AS 2.625 ml50 ml100 ml200 ml / 250 ml500 ml1000 mlIdent. No.1 1234300 AS 2.12 1234400 AS 2.23 1234500 AS 2.34 1234600 AS 2.45 1234700 AS 2.56 3819300 AS 2.61 AS 2.1 Fixing clip2 AS 2.2 Fixing clip3 AS 2.3 Fixing clip4 AS 2.4 Fixing clip5 AS 2.5 Fixing clip6 AS 2.6 Fixing clipIdent. No.3342400VG 3.37 Microtiter plate attachment*For 1 standard microtiter plate (continuousoperation).Ident. No.3344400MS 3.5 PCR plate attachmentFor holding PCR plates, 96-well.Ident. No.34280001 2 34 5 6* For VG 3.3 Universal attachment28 29 30