ExtremeWare 7.5 Error Message Decoder - Extreme Networks

More documents

Recommendations

Info

Critical MessagesCannot Start EAPS eaps.c 421: Error! spawning EAPS taskSoftware VersionExtremeWare 6.2.2 and laterHardware VersionAllExplanationThis message indicates that the EAPS task could not be started.ActionThe switch may have become unstable. Contact Technical Support.36 ExtremeWare Error Message Decoder
Checksum Error on CPU PacketChecksum Error on CPU Packet ERROR: Checksum Error on CPU received pkt.Software VersionExtremeWare 6.1.8b12 and laterHardware VersionAll “i” seriesExplanationThis message indicates a new CPU Cyclic Redundancy Check (CRC). It prevents bad packets from beingpassed up to the CPU.ActionIf this error is seen only once in the log, no action is necessary.If you are using ExtremeWare 6.2.1 (or earlier), use the show log and show tech-support commands,capture the output, and contact Technical Support to troubleshoot the problem.If you are using ExtremeWare 6.2.1 (or later), system health check can be enabled. If the system check isenabled, three consecutive occurrences of the above error triggers automatic recovery of the port or themodule. If the software can detect the error, it will correct the error. However, if the software is unableto detect the error, it will take the module offline.NOTEIf you are using ExtremeWare 6.2.1 or later, run the pktScan utility to identify and correct the problem.If you are using ExtremeWare 6.2.2 (or later), you can take the module either offline or keep it onlineeven if automatic recovery fails.ExtremeWare Error Message Decoder 37
Page 1 and 2: ExtremeWareError Message DecoderExt
Page 3: ContentsPrefaceIntroduction 19Conve
Page 7 and 8: ContentsHTTPD Bind Failed 140Rx Buf
Page 9 and 10: ContentsNo MAC Entries Available on
Page 11 and 12: ContentsActivate Failed, No PIF 273
Page 13 and 14: ContentsInvalid Time Values 341IP F
Page 15 and 16: ContentsUnable to Start Watchdog Ti
Page 17 and 18: ContentsRing Down, Flush Domain FDB
Page 19 and 20: PrefaceThis guide lists the most co
Page 21 and 22: 1 Emergency Error MessagesEmergency
Page 23 and 24: Hot SwapHot SwapSWL-AL03 KERN: ngRx
Page 25 and 26: netJob ErrornetJob ErrorfdbAgeTask
Page 27 and 28: VDSL Read/WriteVDSL Read/WriteCould
Page 29 and 30: 2 Alert MessagesAlert messages indi
Page 31 and 32: VDSL Port Not ReadyVDSL Port Not Re
Page 33 and 34: Cable Diagnostics on Port FailedCab
Page 35: 3 Critical MessagesCritical message
Page 39 and 40: Checksum Error on External PortChec
Page 41 and 42: Checksum Error on MotherboardChecks
Page 43 and 44: Checksum Error on EDP Packet and Sl
Page 45 and 46: CPU DialogueCPU Dialogue Missed CPU
Page 47 and 48: EAPS Domain Does Not ExistEAPS Doma
Page 49 and 50: EAPS SendEAPS Sendeaps.c407:Error!e
Page 51 and 52: Fail Timer Expired, State CompleteF
Page 53 and 54: Firmware Download FailedFirmware Do
Page 55 and 56: High CPU Utilization, fdbAgeTaskHig
Page 57 and 58: Illegal Calibration DataIllegal Cal
Page 59 and 60: Invalid EAPS Domain Instance 65, Ou
Page 61 and 62: Invalid PTAGInvalid PTAG ptagInvali
Page 63 and 64: Maximum Limit for VLANsMaximum Limi
Page 65 and 66: MII ResetMII Reset MAC: Port = 20 f
Page 67 and 68: msgQSend Error, OSPF ExceptionmsgQS
Page 69 and 70: MSM Connection BrokenMSM Connection
Page 71 and 72: Not a Control VLANNot a Control VLA
Page 73 and 74: Out of MBufsOut of MBufs eaps_runti
Page 75 and 76: Out of Memory, Adding Protected VLA
Page 77 and 78: Out of Memory, Creating EAPS Domain
Page 79 and 80: Packet Corruption on MotherboardPac
Page 81 and 82: PoE Firmware Update FailedPoE Firmw
Page 83 and 84: Power Supply Failure, No Backup Ava
Page 85 and 86: Power Supply Failure, Trying AgainP
Page 87 and 88:
Received PDUs from Two NodesReceive
Page 89 and 90:
sbmfree Doublesbmfree Double sbmfre
Page 91 and 92:
Software ErrorSoftware Error eaps.c
Page 93 and 94:
sysEnvMsg msgQSend ErrorsysEnvMsg m
Page 95 and 96:
TCP ConnectionTCP Connection HC: is
Page 97 and 98:
Twister Access TimeoutTwister Acces
Page 99 and 100:
VLAN Not FoundVLAN Not Found eaps.c
Page 101 and 102:
Watchdog Timer RebootWatchdog Timer
Page 103 and 104:
Write to NVRAM FailedWrite to NVRAM
Page 105 and 106:
Power Supply NormalPower Supply Nor
Page 107 and 108:
Corrupted Backplane Health Check Pa
Page 109 and 110:
Download Configuration Task Spawn F
Page 111 and 112:
Configuration Download Size Too Lar
Page 113 and 114:
Add and Remove Xen CardAdd and Remo
Page 115 and 116:
Receive Task Spawn FailedReceive Ta
Page 117 and 118:
LSM Filter: Drop Received PacketLSM
Page 119 and 120:
Memory Allocation FailedMemory Allo
Page 121 and 122:
Packet Received is Not an LSM Packe
Page 123 and 124:
Transmission Message Queue Creation
Page 125 and 126:
Access Profile Configuration Restor
Page 127 and 128:
Access Profile Configuration Entrie
Page 129 and 130:
Access List with Invalid Pointer or
Page 131 and 132:
Cannot Create Access List Instance
Page 133 and 134:
Invalid Access List Instance for Te
Page 135 and 136:
Cannot Create Security Management L
Page 137 and 138:
Cannot Create Security Management L
Page 139 and 140:
HTTPD Socket Non-blocking IOCTL Fai
Page 141 and 142:
Rx Buffer Allocation FailedRx Buffe
Page 143 and 144:
Checksum Error on SlotChecksum Erro
Page 145 and 146:
Card Diagnostic FailedCard Diagnost
Page 147 and 148:
CPU Control TimeoutCPU Control Time
Page 149 and 150:
Corrupted Packets on M-BRDCorrupted
Page 151 and 152:
Task Running During Watchdog Timer
Page 153 and 154:
MSM Rebooted by SlaveMSM Rebooted b
Page 155 and 156:
EDP Frame in Wrong FormatEDP Frame
Page 157 and 158:
Session Timeout While Accessing FDB
Page 159 and 160:
System Recovery ActionSystem Recove
Page 161 and 162:
EDP Frame with Bad LengthEDP Frame
Page 163 and 164:
Error Reading MACError Reading MACs
Page 165 and 166:
Diagnostics FailedDiagnostics Faile
Page 167 and 168:
AFC Status TimeoutAFC Status Timeou
Page 169 and 170:
4 Error MessagesError messages indi
Page 171 and 172:
Cannot Create VLANCannot Create VLA
Page 173 and 174:
Delete FDB EntryDelete FDB EntryMSM
Page 175 and 176:
ExtremeWare Synchronization Error,
Page 177 and 178:
fetchPacket64 FailedfetchPacket64 F
Page 179 and 180:
Initialization FailedInitialization
Page 181 and 182:
Invalid Link SpeedInvalid Link Spee
Page 183 and 184:
Link DownLink DownN9_BD6800_Sec SYS
Page 185 and 186:
Messages from Interrupt Level LostM
Page 187 and 188:
No PIF for BIFNo PIF for BIF stpPor
Page 189 and 190:
PBUS CRC ErrorPBUS CRC ErrorERROR:
Page 191 and 192:
PoE Firmware Invalid on SlotPoE Fir
Page 193 and 194:
PoE Not OperationalPoE Not Operatio
Page 195 and 196:
Power Consumption Normal for SlotPo
Page 197 and 198:
Send Slave Config Length ErrorSend
Page 199 and 200:
VDSL vPowReadVDSL vPowReadvPowRead
Page 201 and 202:
VLAN ID ConflictVLAN ID Conflict te
Page 203 and 204:
GPP Initialization ErrorGPP Initial
Page 205 and 206:
Unsupported Data TypeUnsupported Da
Page 207 and 208:
No MAC Entries Available on lkup Ta
Page 209 and 210:
sysObjSetStpd Returned Error for St
Page 211 and 212:
sysObjSetStpPort Returned Error for
Page 213 and 214:
Failed to Send Timer Tick to DLA Ta
Page 215 and 216:
Auto Diagnostic Running While Timer
Page 217 and 218:
Cable Diagnostic Module Message Que
Page 219 and 220:
Manual Diagnostics In ProgressManua
Page 221 and 222:
Message Queue Receive FailedMessage
Page 223 and 224:
No Physical Port Associated to STP
Page 225 and 226:
PPP Link Configuration Too ShortPPP
Page 227 and 228:
STP Timer Message Queue Send Failed
Page 229 and 230:
No Response for PPP Link Status Mes
Page 231 and 232:
Unable to Set Global Status Message
Page 233 and 234:
Could Not Get VLAN InstanceCould No
Page 235 and 236:
HTTP User Authentication FailedHTTP
Page 237 and 238:
HTTP Initialization FailedHTTP Init
Page 239 and 240:
DOSprotect: Filter Precedence Confl
Page 241 and 242:
DOSprotect Timeout: ACL RemovedDOSp
Page 243 and 244:
Failed to Get HTTPS Port NumberFail
Page 245 and 246:
Reading Private Key FailedReading P
Page 247 and 248:
Create VLAN Request: VlanIfIndex Ex
Page 249 and 250:
PSU Output FailedPSU Output FailedP
Page 251 and 252:
Error Reading RegisterError Reading
Page 253 and 254:
Active MSM Failed to Program FLASHA
Page 255 and 256:
Error Getting Information on Intern
Page 257 and 258:
Failed to Delete RIP RouteFailed to
Page 259 and 260:
Session Time Out While Reading Regi
Page 261 and 262:
Slave NMC Not ActiveSlave NMC Not A
Page 263 and 264:
Enabling and Disabling Auto Polling
Page 265 and 266:
Unsupported GBICUnsupported GBICUns
Page 267 and 268:
Internal Links on Card DownInternal
Page 269 and 270:
Cannot Read TemperatureCannot Read
Page 271 and 272:
5 Warning MessagesWarning messages
Page 273 and 274:
Activate Failed, No PIFActivate Fai
Page 275 and 276:
Bad Ethernet Type/LengthBad Etherne
Page 277 and 278:
Bad MAC ReadBad MAC Read WARNING: S
Page 279 and 280:
ASIC ErrorASIC Error ERROR: Blizzar
Page 281 and 282:
Bracket Buffer FullBracket Buffer F
Page 283 and 284:
Btree Insert FailedBtree Insert Fai
Page 285 and 286:
Cannot Allocate Memory for TimerCan
Page 287 and 288:
Cannot Get Memory Buffer Transactio
Page 289 and 290:
Cannot Send CardCannot Send Card Ca
Page 291 and 292:
Cannot Send nmcCannot Send nmc Cann
Page 293 and 294:
Card RemovedCard RemovedSYST: card.
Page 295 and 296:
Checksum Error on PDUChecksum Error
Page 297 and 298:
Control VLAN Not Configured for EAP
Page 299 and 300:
Datagram FragmentDatagram Fragment
Page 301 and 302:
Delete Failed, EAPS InterfaceDelete
Page 303 and 304:
Delete Failed, FDB EntryDelete Fail
Page 305 and 306:
Delete Failed, No PIFDelete Failed,
Page 307 and 308:
Diagnostic Failure, Port Invalid Sp
Page 309 and 310:
Domain Already ExistsDomain Already
Page 311 and 312:
Dropped Bytes Condition SetDropped
Page 313 and 314:
EAPS Task Not RunningEAPS Task Not
Page 315 and 316:
EDP Not EnabledEDP Not Enabled eaps
Page 317 and 318:
ESRP Enabled, Action Not PossibleES
Page 319 and 320:
Exceeded Committed-Rate Condition S
Page 321 and 322:
Failed to Obtain StatisticsFailed t
Page 323 and 324:
FDB Entry Not FoundFDB Entry Not Fo
Page 325 and 326:
Free ListFree List Trying to put bl
Page 327 and 328:
Get EEPROM ErrorGet EEPROM Error st
Page 329 and 330:
Incorrect StateIncorrect State setP
Page 331 and 332:
Insufficient Memory, PIF StructureI
Page 333 and 334:
Invalid BPDUInvalid BPDU StpProcess
Page 335 and 336:
Invalid EAPS Object IDInvalid EAPS
Page 337 and 338:
Invalid PIF for PortInvalid PIF for
Page 339 and 340:
Invalid Port SpeedInvalid Port Spee
Page 341 and 342:
Invalid Time ValuesInvalid Time Val
Page 343 and 344:
IP Output (Slow Path)IP Output (Slo
Page 345 and 346:
iQuery MessageiQuery Message SLB 3D
Page 347 and 348:
Load Share Trunk InactiveLoad Share
Page 349 and 350:
MAC TypeMAC Type unknown MAC type o
Page 351 and 352:
msgQSend Message Queue FullmsgQSend
Page 353 and 354:
MSM Module Type MismatchMSM Module
Page 355 and 356:
No Associated STPD PortNo Associate
Page 357 and 358:
No EAPSD-Bridge Links ExistNo EAPSD
Page 359 and 360:
No Message BufferNo Message Buffer
Page 361 and 362:
otpRamBusyotpRamBusySYST: Port 12 l
Page 363 and 364:
Port Binding Failed, Bound to Anoth
Page 365 and 366:
Port Creation Failed, Bad STPD Inst
Page 367 and 368:
Port Creation Failed, Not Enough Po
Page 369 and 370:
Port Deletion Failed, Not Bound to
Page 371 and 372:
Port Not ConfiguredPort Not Configu
Page 373 and 374:
Port Unbinding Failed, STP Not Disa
Page 375 and 376:
Power Consumption Exceeds Slot Thre
Page 377 and 378:
Problem Stopping DomainProblem Stop
Page 379 and 380:
PTAG Error, Memory BlocksPTAG Error
Page 381 and 382:
edirectServerList Not in Useredirec
Page 383 and 384:
Send Message FailedSend Message Fai
Page 385 and 386:
SNMP IP QoS ACL MissingSNMP IP QoS
Page 387 and 388:
STP Disabled for PortSTP Disabled f
Page 389 and 390:
STPD Instance Does Not ExistSTPD In
Page 391 and 392:
STPD Table Malloc FailedSTPD Table
Page 393 and 394:
STP Port Does Not ExistSTP Port Doe
Page 395 and 396:
STPD Tag Removal FailedSTPD Tag Rem
Page 397 and 398:
System OverheatedSystem OverheatedS
Page 399 and 400:
Task Exceeded Stack BoundaryTask Ex
Page 401 and 402:
Timer Delay Exceeds CapacityTimer D
Page 403 and 404:
Timer Error, Wrong BucketTimer Erro
Page 405 and 406:
Trying to Put Block in Free ListTry
Page 407 and 408:
Unable to Create Message QueueUnabl
Page 409 and 410:
Unable to Start Watchdog TimerUnabl
Page 411 and 412:
Unknown PDU TypeUnknown PDU Type ea
Page 413 and 414:
Untagged Port MismatchUntagged Port
Page 415 and 416:
User Account Out of RangeUser Accou
Page 417 and 418:
VLAN Already ExistsVLAN Already Exi
Page 419 and 420:
VLAN Does Not Contain PortVLAN Does
Page 421 and 422:
VLAN ID No Longer in STPDVLAN ID No
Page 423 and 424:
VLAN Is Not Protected VLANVLAN Is N
Page 425 and 426:
Slot Number Out of RangeSlot Number
Page 427 and 428:
FDB Scan Entries RemappedFDB Scan E
Page 429 and 430:
Bridge and EAPSD Link ExistsBridge
Page 431 and 432:
6 Notice MessagesNotices are inform
Page 433 and 434:
Port Cannot PowerPort Cannot PowerN
Page 435 and 436:
7 Informational MessagesInformation
Page 437 and 438:
Cannot Allocate Memory BufferCannot
Page 439 and 440:
EEPROM Read RetriedEEPROM Read Retr
Page 441 and 442:
Fail Timer Flag Cleared, EAPS=E05BF
Page 443 and 444:
Fail Timer Flag SetFail Timer Flag
Page 445 and 446:
Firmware RevisionFirmware RevisionS
Page 447 and 448:
Flush PDUFlush PDU eaps.c 1548: Rec
Page 449 and 450:
Log ClearedLog ClearedSYST: Log cle
Page 451 and 452:
Master Domain Stopped, Primary Port
Page 453 and 454:
Master Node State Changed to Failed
Page 455 and 456:
Master State Changed to CompleteMas
Page 457 and 458:
Old Power SuppliesOld Power Supplie
Page 459 and 460:
PoE InitializedPoE InitializedSlot
Page 461 and 462:
Port Power State ChangePort Power S
Page 463 and 464:
Power Is Up for SlotPower Is Up for
Page 465 and 466:
Preforward Timer Expired, EAPS=E38A
Page 467 and 468:
Primary Port Status Changed to Bloc
Page 469 and 470:
Primary Port Status Changed to Up,
Page 471 and 472:
QoS Profile, Invalid QoS Configurat
Page 473 and 474:
RIP, MBZ FieldRIP, MBZ Field ripInp
Page 475 and 476:
Ring Down, Flush Domain FDBRing Dow
Page 477 and 478:
Ring Up, Flush FDB on DomainRing Up
Page 479 and 480:
Ring-Port State Changed to Link-Dow
Page 481 and 482:
Secondary Port Status Changed to Do
Page 483 and 484:
Secondary Port Status Changed to In
Page 485 and 486:
Secondary Port Status Changed to Un
Page 487 and 488:
Secondary Port Status Changed to Up
Page 489 and 490:
Secondary Port Status Changed to Up
Page 491 and 492:
System RebootedSystem RebootedSYST:
Page 493 and 494:
Transit Domain Stopped, Primary Por
Page 495 and 496:
Transit Node State Changed to Links
Page 497 and 498:
Updating PoE CalibrationUpdating Po
Page 499 and 500:
Index PositionIndex PositionIndex P
Page 501 and 502:
Initializing GPP ModuleInitializing
Page 503 and 504:
Started Cable Diagnostics in Manual
Page 505 and 506:
Updating BootROM ImageUpdating Boot
Page 507 and 508:
PSU Output ReadyPSU Output ReadyPSU
Page 509 and 510:
8 Debug MessagesDebug messages are
Page 511 and 512:
Invalid DestinationInvalid Destinat
Page 513 and 514:
pqmWaitKill FailedpqmWaitKill Faile
Page 515 and 516:
QuakeWaitPbut2CacheXfer FailedQuake
Page 517 and 518:
RIP/VLSMRIP/VLSM ripSupply: Error 5
Page 519 and 520:
Failed to Send FDB Age MessageFaile
Page 521 and 522:
RpSearchNetLoginRomObjectList: Sear
Page 523 and 524:
Associated MAC Not FoundAssociated
Page 525 and 526:
Card State InformationCard State In
Page 527 and 528:
IndexNumerics100 messages queued 50
Page 529 and 530:
frame with bad length 161not enable
Page 531 and 532:
2463 465, 4662523 4692534 4872561 4
Page 533 and 534:
spurious link state 386state blocke
Page 535 and 536:
does not contain port 419does not e
show all

ExtremeWare 7.5 Error Message Decoder - Extreme Networks

Create successful ePaper yourself

Delete template?

Save as template?