4-BTV, 5-BTV, 6-BTV Multiband HF - K6RF Home of the Porta Base ...

More documents

Recommendations

Info

Installing Radials & Feedline on the Hustler Base If you are connecting the radial wires directly to the antenna base, use the following drawing showing the hardware required. This diagram also shows connecting the feedline direct to the Hustler base using the supplied lugs for coax connections. For radial wires, the better alternative is to use an optional DXE-RADP-3 DX Engineering Radial Plate. Additionally, the feedline can be connected using other methods using DX Engineering custom made feedline options as shown in Chapter 6. - 28 -
Coax RF Choke Hustler recommends a wound coax type of choke to help prevent RF feedback into the radio room. The following diagram shows the coax cable choke system which offers modest performance on some bands. The better alternative is the optional DX Engineering DXE-VFCC-H05-A Vertical Feedline Current Choke which is specifically engineered and manufactured to help eliminate RF feedback from a resonant vertical antenna. More information on the VFCC can be found in Chapter 6. Basic Tuning In a few basic installations adjustment of the antenna to obtain the lowest SWR may not be necessary. However, a broad, low SWR over an entire band or all bands is an indication of poor efficiency. If at all possible, the addition of radials will improve performance as detailed in Chapters 4 and 6. For ground mounted installations the length of radials is not critical and they cannot be used to change the tuning. Elevated system radials are resonant and they need to be pruned to lengths for the bands that are used. Slight adjustments of SWR minimums can be made by shortening or lengthening the starting dimensions between the antenna tubing sections and the traps in performance installations. These adjustments may not provide enough changes and you will have to proceed with Trap Calibration for additional tuning instructions in Chapter 7. Do NOT cut the antenna tubing. - 29 -
Page 1 and 2: 4-BTV, 5-BTV, 6-BTV Multiband HF Ve
Page 3 and 4: Chapter 7 - Tuning Understanding Tr
Page 5 and 6: Hustler BTV Antennas The Hustler 4-
Page 7 and 8: Chapter 2 - General Information War
Page 9 and 10: Site Selection • Install your new
Page 11 and 12: Coaxial Cable to Mounting Pipe The
Page 13 and 14: of any metal. We recommend four res
Page 15 and 16: vertical section of the antenna. Th
Page 17 and 18: Chapter 5 - Basic BTV Assembly Asse
Page 19 and 20: Hustler Base Assembly The Hustler B
Page 21 and 22: Assembly of the 4-BTV Antenna Verti
Page 23 and 24: Assembly of the 5-BTV Antenna Verti
Page 25 and 26: 6-BTV Package Contents Qty Part Num
Page 27: Mating the Vertical Sections to the
Page 31 and 32: The installation and tuning is bree
Page 33 and 34: Attaching Ground Radial Wires to th
Page 35 and 36: Testing the Tilt Base Test the tilt
Page 37 and 38: A second method that may be used is
Page 39 and 40: Chapter 7 - Tuning Understanding Tr
Page 41 and 42: You must adjust each trap with the
Page 43 and 44: Tuning the 80 Meter Resonator Whip
Page 45 and 46: Chapter 9 - Reference Information E
Page 47 and 48: these "coupling radials" that you n
Page 49 and 50: Hustler BTV Replacement Parts Diagr
Page 51 and 52: Antenna Specifications Copyright ©
Page 53 and 54: Copyright © New-Tronics Antenna Co
Page 55 and 56: Chapter 11 - Recommended Accessory
Page 57 and 58: DXE-RADW - 500K or 1000K Bulk Radia
Page 59 and 60: DXE-CBC-008U002 24 Inch RG-8 Foam,

4-BTV, 5-BTV, 6-BTV Multiband HF - K6RF Home of the Porta Base ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?