SPRING CA T ALOGUE - Lee Spring

More documents

Recommendations

Info

COMPRESSION SPRINGS SPECIFICATION FORMCompression springs are generally specified to work in a bore or over a rod. Theycan be supplied with end coils closed and ground square for optimum alignmentand reduced solid height. Springs can also be pre-stressed during manufacture tomaintain length at elevated stress levels.IIIIIIIVCLOSED &GROUND ENDS.RHLHCLOSED ENDS,NOT GROUND.OPEN ENDS,NOT GROUND.OPEN ENDS,GROUND.INSIDE DIAMETER+/-+/-OR WORKS OVERMAX SOLID HEIGHTOUTSIDE DIAMETERFREE LENGTH +/-OR WORKS ININDICATE UNITS OF MEASURE (IN & LB), (MM & N)1. MATERIAL2. WIRE DIA.3. DIRECTION OF WIND OPT LH RH4. STYLE OF END I II III IV5. SQUARENESS6. RATE +/- BETWEEN &7. LOAD 1 +/- @8. LOAD 2 +/- @9. No. OF ACTIVE COILS10. TOTAL No. OF COILS11. FINISH12. FREQUENCY OF COMPRESSION CYCLES/SECAND WORKING RANGE IN. TO IN. OF LENGTH13. OPERATING TEMP °c14. OTHERQUANTITY TO QUOTE FOR ____________________________________________________________________________________________CUSTOMER NAME:A/C No:ENQUIRY TAKEN BY:DATE TO SUPPLIER:CUSTOMER CONTACTDATE PRICE RECEIVED:TEL No:EMAIL:Sales Hotline: Tel: +44 (0)118 978 1800 Fax: +44 (0)118 977 4832 or order online @ www.leespring.co.uk155
CONICAL SPRINGS SPECIFICATION FORMConical springs are specified where the large end is designed to work in a bore andthe small end fits over a rod. Springs of this type offer reduced solid height comparedto straight compression springs, especially when they are capable of ‘telescoping’.IIICLOSED & GROUNDENDS.CLOSED ENDS, NOTGROUND.INSIDE DIAMETERFREE LENGTHMAX SOLID HEIGHT+/-+/-OUTSIDE DIAMETER+/-INDICATE UNITS OF MEASURE (IN & LB), (MM & N)1. MATERIAL2. WIRE DIA.3. DIRECTION OF WIND OPT LH RH4. STYLE OF END I II5. RATE +/- BETWEEN &6. LOAD 1 +/- @7. LOAD 2 +/- @8. No. OF ACTIVE COILS9. TOTAL No. OF COILS10. FINISH11. FREQUENCY OF COMPRESSION CYCLES/SECAND WORKING RANGE IN. TO IN. OFLENGTH12. OPERATING TEMP °c13. OTHERQUANTITY TO QUOTE FOR ____________________________________________________________________________________________CUSTOMER NAME:A/C No:ENQUIRY TAKEN BY:DATE TO SUPPLIER:CUSTOMER CONTACTDATE PRICE RECEIVED:TEL No:EMAIL:156Sales Hotline: Tel: +44 (0)118 978 1800 Fax: +44 (0)118 977 4832 or order online @ www.leespring.co.uk
Page 2 and 3:
CONTENTSIntroduction 2Stock springs
Page 4 and 5:
On page 164 you will find a glossar
Page 6 and 7:
WAVE SPRINGSGuide to using tablesRo
Page 8 and 9:
REDUX WAVE SPRINGSLEESTOCKNUMBERHOL
Page 10 and 11:
REDUX WAVE SPRINGSLEESTOCKNUMBERHOL
Page 12 and 13:
CONSTANT FORCE SPRINGSLEESTOCKNUMBE
Page 14 and 15:
LITE PRESSURE COMPRESSION SPRINGS
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 27 and 28:
Page 29 and 30:
COMPRESSION SPRINGS● End Coils Cl
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
HEAVY DUTY COMPRESSION SPRINGS● E
Page 100 and 101:
HEAVY DUTY COMPRESSION SPRINGS● E
Page 102 and 103:
DIE SPRINGSGuide to using tablesMax
Page 104 and 105:
DIE SPRINGSMedium Load - Grey● Id
Page 106 and 107: DIE SPRINGSMedium Load Plus - Beige
Page 108 and 109: DIE SPRINGSMedium Heavy Load - Purp
Page 110 and 111: DIE SPRINGSHeavy Load - Black● Id
Page 112 and 113: DIE SPRINGSExtra Heavy Load - Orang
Page 114 and 115: EXTENSION SPRINGS● Full Loops, Ra
Page 140 and 141: LEESTOCKNUMBERCONTINUOUS LENGTH EXT
Page 142 and 143: LEESTOCKNUMBERCONTINUOUS LENGTH EXT
Page 144 and 145: TORSION SPRINGS90º● Left Hand or
Page 146 and 147: TORSION SPRINGS270º● Left Hand o
Page 148 and 149: BATTERY SPRINGSGuide to using table
Page 150 and 151: BELLEVILLE SPRING WASHERSGuide to u
Page 152: BELLEVILLE SPRING WASHERS● Manufa
Page 158 and 159: EXTENSION SPRINGS SPECIFICATION FOR
Page 160 and 161: DRAWBAR SPRINGS SPECIFICATION FORMD
Page 162 and 163: BATTERY SPRINGS SPECIFICATION FORMB
Page 164 and 165: SPECIFICATIONS & TOLERANCESAll the
Page 166 and 167: USING MICRONS0.00254mm(0.0001")Huma
Page 168 and 169: CONVERSION DATAQuantity To convert
Page 170: EUROPE ASIA NORTH & SOUTH AMERICAww
show all

SPRING CA T ALOGUE - Lee Spring

Create successful ePaper yourself

Delete template?

Save as template?