For Cutting and Machining Pipe, Tube and Boiler Panels - ESCO Tool
For Cutting and Machining Pipe, Tube and Boiler Panels - ESCO Tool
For Cutting and Machining Pipe, Tube and Boiler Panels - ESCO Tool
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
8<br />
““““ AAAA iiii rrrr CCCC llll aaaa mmmm pppp ””””<br />
Ideal for <strong>Tube</strong> Fabrication Facilities, the<br />
MILLHOG ® Production End Prep <strong>Tool</strong>s<br />
equipped with the “Air Clamp” have<br />
increased production by more than 300%!!!<br />
Key features<br />
• Locks tool instantly to tube I.D.<br />
• Disengages immediately with the flip of a<br />
switch<br />
• Significantly decreases cycle time<br />
between end preps<br />
• Ideal for boiler tube component<br />
fabrication<br />
• Bevel face <strong>and</strong> bore in one operation<br />
• Rugged braided hose to control air flow<br />
• Simple to operate<br />
• Retrofits to existing MILLHOG ® end prep tools<br />
• Esco lock blade locking system delivers<br />
superior blade performance<br />
<strong>Tool</strong> Applications<br />
• <strong>Boiler</strong> tube panel fabrication<br />
• <strong>Tube</strong> sheet seal weld removal<br />
• <strong>Tube</strong> sheet end facing<br />
• End prep large numbers of consistent size<br />
tube <strong>and</strong> pipe<br />
Air Clamp Series<br />
• Ground Millhog<br />
• Mongoose Millhog<br />
• <strong>Tube</strong> Weasel Millhog<br />
Production Increases Over 300%<br />
The MILLHOG ® “Air Clamp” is designed for<br />
shop use when cycle time between end preps<br />
needs to be minimized. A side by side<br />
comparison shows, end prep production can<br />
increase by more than 300% using the<br />
“Air Clamp” when compared to a manually<br />
actuated clamping system.<br />
The “Air Clamp” instantly locks the tool to the<br />
pipe or tube i.d <strong>and</strong> holds it securely in place<br />
while performing the end prep. When done,<br />
removing the tool from the work is simple,<br />
reverse the valve <strong>and</strong> the clamps disengage<br />
automatically releasing the tool from the tube<br />
I.D. immediately.<br />
Easy to install, the “Air Clamp” can be fitted to<br />
an existing “Mongoose”, “Ground”, <strong>and</strong> “<strong>Tube</strong><br />
Weasel” MILLHOG ® in minutes, <strong>and</strong> requires<br />
no special tools of training.<br />
®<br />
Ideal for <strong>Tube</strong> Fabrication Facilities...<br />
Automatic I.D. Clamping End Prep <strong>Tool</strong><br />
Built for production, the “Air Clamp” series MILLHOGS are ideal for tube<br />
fabrication shops that do large numbers of end preps on tube <strong>and</strong> pipe of<br />
consistent size.<br />
Operators will like the quick action of the “Air Clamp”. This simple innovation is<br />
easy to use, increases production, <strong>and</strong> minimizes operator fatigue by<br />
eliminating the tedious <strong>and</strong> time consuming task of manual clamping.<br />
Designed to last, “Air Clamp” MILLHOGS are built on the reliable MILLHOG ®<br />
dual opposed, bearing supported gear drive system that has performed<br />
millions of end preps on all types of tube <strong>and</strong> pipe alloys proving itself to be<br />
second to none for durability <strong>and</strong> performance.<br />
“Air Clamp” MILLHOGS also feature the “EscoLock” blade locking system that<br />
holds the cutting blade so rigid that MILLHOGS are capable of<br />
producing 2-3 more end preps per blade, <strong>and</strong> in less time than competitive<br />
tools. This helps make the “Air Clamp” MILLHOGS the fastest <strong>and</strong> most cost<br />
efficient end prep tools you can use in a production application.<br />
To operate, simply acuate the valve,<br />
<strong>and</strong> the clamps instantly lock the tool<br />
into position. Reverse the valve, <strong>and</strong><br />
the clamps disengage from the I.D<br />
immediately.<br />
“Air Clamps” are available for<br />
the “Ground”, “<strong>Tube</strong> Weasel”<br />
<strong>and</strong> “Mongoose” Millhog ® ,<br />
<strong>and</strong> can be installed by simply<br />
removing the manual draw rod<br />
assembly <strong>and</strong> attaching the<br />
“Air Clamp”.<br />
esco tool • 75 October Hill Road, Holliston, MA 01746 • 800.343.6926 • 508.429.4441 • Fax 508.429.2811 • e-mail: millhog@escotool.com<br />
Available <strong>For</strong> Sale or Rent