Technical Sheet (PDF Format) - M Barnwell Services Ltd

M BARNWELL SERVICES LTDREGINALD ROADSMETHWICKWEST MIDLANDSB67 5ASTel: +44 (0)121 429 8011Fax: +44 (0)121 434 3016E-mail: sales@barnwell.co.ukWeb: www.barnwell.co.ukSize RangeAs well as the standard ranges such as AS568, AS871, BS1806, BS4518,DIN and JIS B2401, we can supply a full range of metric and imperial crosssections and diameters. Whilst there is no upper limit to the inside diameteravailable, there is a lower limit and the following table shows how small wecan supply these rings.w d1 Solid Core d1 Hollow CoreViton Silicone Viton Silicone1.60 5.00 5.00 N/A N/A1.78 5.28 5.28 N/A 8.002.00 6.80 6.80 10.00 10.002.40 7.40 7.40 12.00 12.002.50 7.40 7.40 12.00 12.002.62 7.60 7.60 16.00 16.003.00 12.00 12.00 20.00 20.003.40 12.50 12.50 23.00 23.003.53 13.00 13.00 24.00 24.003.60 13.00 13.00 24.00 24.004.00 14.00 14.00 28.00 28.004.25 14.50 14.50 32.00 32.004.50 15.00 15.00 35.00 35.005.00 20.00 20.00 42.00 42.005.34 22.00 22.00 48.00 48.005.50 23.00 23.00 50.00 50.005.70 24.00 24.00 60.00 60.006.00 27.00 27.00 75.00 75.006.35 38.00 38.00 90.00 90.006.50 45.00 45.00 95.00 95.006.99 48.00 48.00 100.00 100.008.00 72.00 72.00 150.00 150.008.40 76.00 76.00 160.00 160.009.00 95.00 95.00 175.00 175.009.52 105.00 105.00 200.00 200.0010.00 110.00 110.00 230.00 230.0010.50 112.00 112.00 240.00 240.0011.10 115.00 115.00 250.00 250.0012.00 120.00 120.00 300.00 300.0012.70 130.00 130.00 350.00 350.0014.00 180.00 180.00 390.00 390.0014.30 180.00 180.00 390.00 390.0015.00 250.00 250.00 400.00 400.0015.90 280.00 280.00 450.00 450.0018.00 325.00 325.00 475.00 475.0019.05 350.00 350.00 500.00 500.0020.63 400.00 400.00 550.00 550.0025.40 425.00 425.00 600.00 600.0030.00 475.00 475.00 750.00 700.0032.00 500.00 500.00 850.00 750.00Other cross sections may be possible by special manufacture depending onthe volume, apply for price. Do not stretch small inside diameter rings whenfitting as this results in breakage of the core.Cross section and inner diameter tolerancesThe cross sectional and inside diameter tolerances of this type ofsealing ring differ to those of conventional moulded ’O’ Rings.When produced in medium to larger sizes, the cross section staysquite rounded in profile, but in smaller sizes a degree of ovality(a/r) may occur, due to the jacket material memory giving agreater axial height than radial width.w d1 to d1 w +/- d1 > w +/-1.60 5.00 - 10.00 0.12 0.101.78 5.28 - 12.00 0.12 0.102.00 6.80 - 15.00 0.12 0.102.40 7.40 - 17.00 0.15 0.122.50 7.40 - 17.00 0.15 0.122.62 7.60 - 18.00 0.15 0.123.00 12.00 - 20.00 0.20 0.153.40 12.50 - 22.50 0.20 0.153.53 13.00 - 25.00 0.20 0.153.60 13.00 - 25.00 0.20 0.154.00 14.00 - 30.00 0.30 0.254.25 14.50 - 35.00 0.30 0.254.50 15.00 - 40.00 0.30 0.255.00 20.00 - 45.00 0.30 0.255.34 22.00 - 50.00 0.30 0.255.50 23.00 - 52.00 0.30 0.255.70 24.00 - 54.00 0.30 0.256.00 27.00 - 56.00 0.35 0.306.35 40.00 - 58.00 0.35 0.306.50 45.00 - 59.00 0.35 0.306.99 50.00 - 60.00 0.35 0.308.00 75.00 - 90.00 0.45 0.408.40 76.00 - 100.00 0.45 0.409.00 95.00 - 125.00 0.45 0.409.52 105.00 - 150.00 0.45 0.4010.00 110.00 - 170.00 0.60 0.5010.50 112.00 - 180.00 0.60 0.5011.10 115.00 - 200.00 0.60 0.5012.00 120.00 - 250.00 0.60 0.5012.70 130.00 - 300.00 0.60 0.5014.00 180.00 - 300.00 0.60 0.5014.30 180.00 - 400.00 0.75 0.6015.00 250.00 - 450.00 0.75 0.6015.90 280.00 - 500.00 0.85 0.7018.00 325.00 - 700.00 1.00 0.8019.05 350.00 - 750.00 1.00 0.8020.63 400.00 - 875.00 1.00 0.9025.40 425.00 - 1000.00 1.25 0.9030.00 475.00 - 1250.00 1.50 1.2032.00 500.00 - 1500.00 1.75 1.50Due to the temperature sensitivity of FEP, ‘O’ Ringsare produced and controlled to conform withDIN 7715 M2F.larger d1 leaves w equally roundd1wd1tol5.0mm thro 16.0mm +/- 0.2016.0mm thro 25.0mm +/- 0.2525.1mm thro 40.0mm +/- 0.3540.1mm thro 63.0mm +/- 0.4063.1mm thro 100.0mm +/- 0.50100.1mm thro 160.0mm +/- 0.70smaller d1 leaves w ovalaThereafter, the tolerance will be +/- 0.5% of the nominalinside diameter of the ring.Example : inside diameter of 310.0mmrTolerance = +/- 1.55mm (0.5%)