Solutions for UV Systems 2 Electronic Ballasts for Low Pressure ...

09/2006 

- 1 - 

ZED - ZIEGLER ELECTRONIC DEVICES GMBH 

Table Of Content 

Solutions for UV Systems 2 

Electronic Ballasts for Low Pressure Lamps and Amalgam Lamps 2 

Measurement Technique - Monitors and Sensors 4 

Digital Operation System - a Bus System for UV Facilities 5 

Electronic Ballasts 6 

Recommended Lamp-Ballast Combinations 6 

Special Lamp-Ballast Combinations 8 

Electronic Ballasts (4pin-type) 9 

EVG 11W...20W / 230V AC/ 115V AC/ 24V DC 9 

EVG 30...90W / 230V AC 10 

EVG 100...200W / 230V AC 11 

EVG 200...400W / 230V AC 12 

Electronic Ballasts as Plug-In Cards for Rack Mounting - R(S)-EVG 200...400W / 230V AC 13 

Microprocessor Controlled Electronic Ballasts - P-EVG 200...900W / 230V AC 15 

EVG 30...240W / 115V AC 16 

Single / Twin Electronic Ballasts for Amalgam Lamps - Special Design 18 

UV-Compact MC 30...200W OS - with LCD and Integrated Hour Counter 20 

UV-Compact MC 30...200W - with LCD, Integrated Hour Counter and UV-Monitor 21 

UV-Compact MCplus 200...350W - with LCD, Integrated Hour Counter and UV-Monitor 22 

Electronic Ballasts (2pin-type) 23 

EVG 11W...20W / 230V AC/ 115V AC/ 24V DC 23 

EVG 20...200W / 230V AC 24 

EVG 30...150W / 115V AC 26 

Accessories for Electronic Ballasts 28 

Starting Component ESBS01-1/ESBS01 28 

Measurement Technique - Monitors and Sensors 29 

UV-Monitors - Overview 29 

Recommended Measurement Combinations of Sensors and Monitors 30 

UV-Monitor PRO 2 with Status Indication by LED 31 

UV-Monitor PRO 3 with Relay Contacts and Status Indication by LED 31 

UV-Monitor PRO 5/ PRO 8 with Relay Contacts and Status Indication by LED 32 

UV-Monitor PRO10.4 with Relay Contacts and Status Indication by LED and LCD 33 

Service Device and Service Software for UV-Monitor PRO10 34 

UV-Monitor PRO11 with Relay Contacts and Status Indication by backlighted LCD 35 

UV-Monitor PRO15 with Relay Contacts, Status Indication by LCD, Integrated Hour Counter 36 

UV-Monitor PRO16 with Relay Contacts, Status Indication by LCD, Integrated Hour Counter 37 

UV-Monitor PRO20 for Analog and Digital Multi-Sensoring 38 

UV-Sensors - Overview 39 

Silicon Carbide UV-Diodes 40 

UV-Sensors for Monitoring of Relative UV-Intensities 41 

UV-Sensors with Extended Flare Angle (Side-Looking Sensors) 42 

UV-Sensor SiC007 with various output signals 43 

UV-Sensor SiC021 with various output signals 44 

UV-Sensors adapted to Special Regulations, Calibrated 45 

Measurement Window MF001 for DVGW-/OENORM/SiC007-Sensors 46 

Interfaces IF01, IF02, IF03 for the Connection of Sensors and PLC 47 

Control Units SW5 and SW10 for Lamp Function Control 48 

UV-Radiation Meter UVM-CP 49 

UV-Lamps and Accessories 50 

Quartz Tubes / Immersion Tube Lamps 50 

Contacts and Lamp Sockets for Low Pressure Lamps / Amalgam Lamps 51 

ZED - Ziegler Electronic Devices GmbH - Ilmenauer Strasse 9 - D 987O4 Oehrenstock/Germany 

Phone: ++49 (O) 3677 2O 59 259 - Fax: ++49 (O) 3677 2O 59 26O - url: www.z-e-d.com - E-Mail: info@z-e-d.com

� wide variety of ballasts: 

• ballasts for one, two or four lamp 

operation 

• ballasts with integrated hour counter 

and uv-monitor 

• power range from 10W to 600W 

• lamp current from 100mA to 6A 

• supply voltage 115V AC, 230V AC, 

12V DC and 24V DC 

� instantaneous start without flicker for 

long lamp life time 

� equipped with power factor correction - 

CE-conform 

� lamp faults are indicated by a potential 

free relay contact (alarm trigger); LED´s 

display the current mode of operation 

� up to 30% energy saving compared to 

conventional ballasts 

� preheat on request 

� microprocessor controlled ballasts with 

RS485 port for PLC (Programmable Logic 

Controller) connection 

� starting component for delayed poweron 

of 4 (by cascading up to 16) electronic 

ballasts 

Generals 

Why electronic ballasts? 

The electronic ballast became the standard in the lighting industry. It 

leads to significant energy and money savings in nearly every application. 

The lamp operation is flicker free and the ballast produces virtually 

no noise or hum. 

The incoming 50/60 Hz power (115 or 230 volts) is converted to highfrequency 

AC (usually 20 to 40 kHz). This leads to a constant gas 

discharge compared to conventional ballasts and prevents cathode 

flicker. 

Electronic ballasts are more efficient than magnetic ballasts in converting 

input power to the proper lamp power. The operation of uvlamps 

at higher frequencies reduces end losses, resulting in an 

overall lamp-ballast system efficacy increase of 15% to 20%. 

09/2006 

- 2 - 


Solutions for UV Systems 

Electronic Ballasts for Low Pressure Lamps and Amalgam Lamps 

Electronic ballasts are directly interchangeable with magnetic ballasts. 

They operate with most of available uv-lamps. Long term 

usage has demonstrated the reliability of electronic ballasts. 

Electronic ballasts that operate two or four lamps at once, are allowing 

the use of a single ballast in systems with several lamps. This 

reduces installation and field wiring costs. Other advantages are 

reduced weight, quieter operation and reduced lamp flicker. 

Electronic ballasts basically consist of the following functional units: 

• filter - EMI-filter to attenuate conducted RF noise 

• rectifier 

• PFC (power factor correction) - provides sinusoidal line 

current 

• charging capacitor 

• frequency controller (for high-frequency conversion) 

• power stage 

• resonant tank 

and also 

• fault logic (open-circuit / short-circuit protection) 



Instant, rapid or preheat? 

There are three modes of operation of the lamps: 

09/2006 

� rapid start 

� preheat start (-PH) 

� instant start (-IS) 

Rapid start ballasts 

These ballasts are used for lamps with four-pin connection. 

During startup a short high current pulse is sent to the lamp filament. 

This reduces unwanted sputtering of emissive material at the 

electrodes. 

Compared to instant start ballasts, lamps tend to live longer with 

rapid start ballasts, in case of many on-off cycles. So rapid start 

ballasts are recommended when the switching cycle for the lamps 

is more than three times per day. 

During operation current is flowing through the lamps filament. The 

electrodes of the lamps must fit with this ballast type. 

Preheat start ballasts (-PH) 

These ballasts are also used for lamps with four-pin connection. 

Preheat ballasts provide a preheat current at the filaments that 

allows the electrode to heat up before ignition. During the preheat 

interval, voltage across the lamp drops to a level that reduces the 

unwanted glow current. The ballast applies sufficient voltage to the 

electrodes, long enough for the electrode to reach the emission 

temperature to prevent lamp ignition before the electrodes are 

heated up. 

After the end of programmed time for preheating, the ballast applies 

a voltage across the lamp to ignite it with minimal loss of emissive 

material. This optimizes the lifetime of the lamp. 

These ballasts are intended for applications with many switch on 

cycles. 

We offer preheat start ballasts on request for lamps with a 

minimum power of 200W (see the “PH“ in the type name). 

Instant start ballasts (-IS) 

These ballasts are used for lamps with two-pin connection (see the 

“IS“ in the type name). 

Instant start ballasts ignite lamps by applying high voltage across 

the lamp during setup. The high voltage typically ignites the lamp 

immediatly. These ballasts do not heat the electrodes. 

Instant start ballasts should be used for continously lamp operation 

with less than three switches per day. The advantage is the lower 

wiring effort compared to four-pin connection. 

- 3 - 



Electronic Ballasts for Low Pressure Lamps and Amalgam Lamps 

Operation Modes of Electronic Ballasts 



Monitors 

� wide variety of monitoring units/ 

monitoring features: 

• control units for lamp current 

control 

• monitoring of relative 

uv-intensity 

• monitoring of absolute 

uv-intensity 

• display of specific irradiation by using 

flow rate measurement and reactor 

vessel volume for calculation 

� comfortable status indication by LCD 

� hour counting/lamp lifetime counting 

� potential free relay contacts for status 

indication 

� menu-driven handling and programming 

by buttons or PC-Software for easy 

adjustment and configuration 

� can be integrated easily into existing uvsystems 

� customer specific applications on request 

09/2006 

- 4 - 

Sensors 

� wide variety of sensor -(output-) types: 

• fotodiode 

• current output 

• voltage output 

• sensors adapted to special regulations 

like German or Austrian rule 

� all UV-Sensors operate with SiC diodes 

� daylight blind 

� watertight up to 10bar possible 

(depending on the type of sensor) 

� stainless steel body 

(G1/4’’, G 3/4’’ outside thread 

or plug-in body for measurement 

window MF001) 

� side-looking sensors with enhanced 

angle of incidence for indication of uvradiation 

from side 

� several supply voltages available 

� customer specific adjustment on request 

� measurement window MF001 available 

� interfaces for the connection of sensors 

and PLC (programmable logic controller) 

available 



Measurement Technique - Monitors and Sensors 



Functions 

• each component identifies itself on the bus 

and exchanges information about component 

parameters 

• the system components communicate 

directly to each other 

• four wire bus cable connects all components 

of the system 

Digital Sensor Features 

• absolute value detection 

• sensor includes several measuring ranges, 

the measuring range is changed automatically 

depending on the current uv-intensity 

• no separate sensor adjustment for different 

uv-lamp/sensor arrangements 

Electronic Ballast Features 

• lamp/ballast control 

software aided by PLC or standard PC 

• adjustment of several lamp/ballast parameters 

• internal hourmeter 

Components 

09/2006 

- 5 - 


Digital Operation System 

Bus System for UV Facilities 

unique digital interface for ballasts, sensors, processors and displays 

Electronic Ballasts Digital Sensors Accessories UV Monitor 

P-EVG2x[200...350]W/2...2,1A D-SiC003(-PG)(-F) Interface IF03 

PRO11 

P-EVG800...900W/4...11A 

RS-EVG220...400W/2...4,8A 

D-SLS-SiC003(-PG)(-F) 


for connection 

of uv-diode output sensors 

PRO16 

PRO20 

RS-EVG2x[220...320W]/2...2,2A D-SiC007(-PG)(-F) 

D-SiC021(-PG)(-F) 

D-SiCDVGW 

D-SiCONORM 

PLC 

Advantages 

• digital transmission of signals provides 

high noise immunity which allows larger 

cable length for sensors 

• lower costs for wiring of the system 

Technical Specification 

• interface units can be used to communicate 

with PLC, PC or modem based controllers 

and allow remote monitoring 

• open interface protocol allows third party’s 

adaptions 

• measurement values and commands are 

transmitted digitally 

• digital sensors for low pressure lamps: one 

sensor for the complete output range from 

0,1 up to 200W/m² 

• digital sensors for medium pressure lamps: 

one sensor for the complete output range 

from 1,0 up to 2000W/m² 

• lamp control: on/off, dimming, preheating, 

status, lamp power/voltage 

• ballast control: switch-on current=operating 

current, input voltage control, undervoltage 

switch-off 

• setup and service become more easy 

• extension of the system is possible 

• very complex systems can be designed 

mains voltage: 230V AC ± 10% CE-conform: yes 

mains frequency: 45...65Hz 

bus system: RS485 two wire + GND + U B max. bus cable length: 500m 

• exchange of communication and error 

messages 

• no additional controller components 

needed 

• measuring output as plain text with numerical 

value and scale unit 

• measuring value request by simple standard 

terminal program (e.g. WINDOWS 

terminal.exe) or by comfortable customer 

• dimming with current compensation in the 

lamps filaments 

• preheating and cable length compensation 

• readout of lamp/ballast status (error 

code), correct connection, filament status, 

operation hours... 

• multi-sensoring (mapping of sensors and 

corresponding UV lamps) can be 

programmed 



02/2007 

- 6 - 


Electronic Ballasts 

Recommended Lamp-Ballast Combinations 

Please note: We offer the adaption of the ballast to your special lamp or we design your own ballast. 

G36T5 

G64T5 

GHO36T5 

GHO64T5 

GIA120 

GIA200 

GIA240 

GPH212T5L 

GPH287T5L 

GPH303T5L 

GPH356T5L 

GPH436T5HO 

GPH436T5L 

GPH793T5 

GPH846T5 

GPH846T5HO 

GPH893T5HO 

NNI120 

NNI200 

NNI201/107XL 

NNI300/147XL 

NNI400 

NNI60/25U 

NNI80/36U 

TUV11WT5 

TUV16 

TUV18PLL 


TUV36T5 

TUV36HO 


TUV36SPT5 






TUV64T5HO 


TUV95WHOPLL 

TUV130XPT 





TUV240WXPT 

UNI120 

UNI200 

UNI201 

UNI260 

UNI40 

UNI60 

230V, rapid start, 4-pin 

ST-EVG 11/20 xx x 

EVG11-20W/425mA x x x 

EVG18W/370mA x 

S-EVG30-50W/425mA x x x x x 

EVG2x[30-50W]/425mA x x x x x 

UV Compact MC 30-50W/425mA x x x x x 

S-EVG50-70W/425mA x x 

EVG2x[50-70W]/425mA x x 

UV Compact MC 50-70W/425mA x x 

S-EVG36W/440mA x x 

EVG2x[36W]/440mA x x 

S-EVG35-45W/610mA x 

EVG2x[35-45W]/610mA x 

UV Compact MC 35-45W/610mA x 

S-EVG50-70W/670mA x x 

EVG2x[50-70W]/670mA x x 

UV Compact MC 50-70W/670mA x x 

S-EVG50-70W/760mA x x x 

EVG2x[50-70W]/760mA xx x 

UV Compact MC 50-70W/760mA x x x 

S-EVG65-80W/880mA x x x 

EVG2x[65-80W]/880mA x x x 

UV Compact MC 65-80W/880mA x x x 

S-EVG90W/950mA x 

EVG2x[90W]/950mA x 

S-EVG40-60W/1,2A x x 

EVG2x[40–60W]/1,2A xx 

UV Compact MC 40-60W/1,2A x x 

EVG150-200W/1A x x 

EVG2x[150-200W]/1A x x 

UV Compact MC 150-200W/1A x x 

EVG100-150W/1,5A x x x x 

EVG2x[100-150W]/1,5A x x x x 

UV Compact MC 100-150W/1,5A x x x x 

EVG130W/2,1A x 

EVG2x[130W]/2,1A x 

EVG150-200W/1,5A x x 

EVG2x[150-200W]/1,5A x x 

UV Compact MC 150-200W/1,5A x x 

EVG160-200W/2A x x x 

EVG2x[160-200W]/2A x x 

UV Compact MC 160-200W/2A x x 

EVG2x[220W]/2A x 

R(S)-EVG2x[220W]/2A x 

UV Compact MCplus 220W/2A x 

EVG240W/2A x x x 

P-EVG240W/2A x x x 

R(S)-EVG240W/2A x x x 

UV Compact MCplus 240W/2A x x x 

EVG2x[240W]/2A x x x 

P-EVG2x[240W]/2A x x x 

R(S)-EVG2x[240W]/2A x x x 

EVG270W/3,8A xx 

see next page ⇒ 



R(S)-EVG270W/3,8A x x 

EVG2x[270W]/3,8A xx 

R(S)-EVG2x[270W]/3,8A x x 


R(S)-EVG300W/2,1A x 

UV Compact MCplus 300W/2,1A x 

EVG2x[300W]/2,1A x 

R(S)-EVG2x[300W]/2,1A x 

P-EVG2x[300W]/2,1A x 



UV Compact MCplus 320W/2,2A x 

EVG2x[320W]/2,2A x 

R(S)-EVG2x[320W]/2,2A x 



02/2007 

- 7 - 



Recommended Lamp-Ballast Combinations 

Please note: We offer the adaption of the ballast to your special lamp or we design your own ballast. 

G36T5 

G64T5 

GHO36T5 

GHO64T5 

GIA120 

GIA200 

GIA240 

GPH212T5L 

GPH287T5L 

GPH303T5L 

GPH356T5L 

GPH436T5HO 

GPH436T5L 

GPH793T5 

GPH846T5 

GPH846T5HO 

GPH893T5HO 

NNI120 

NNI200 

NNI201/107XL 

NNI300/147XL 

NNI400 

NNI60/25U 

NNI80/36U 























UNI120 

UNI200 

UNI201 

UNI260 

UNI40 

UNI60 


R-EVG330W/4,8A x 

115V, rapid start, 4-pin 

EVG11-20W/425mA -1 xx x 

S-EVG30–50W/425mA -1 x x x 

EVG2x[30-50W]/425mA -1 x x x 

EVG50–70W/425mA -1 x x 

EVG2x[50-70W]/425mA -1 x x 

EVG35–45W/610mA -1 x 

EVG2x[35-45W]/610mA -1 x 

EVG50–70W/670mA -1 x 

EVG2x[50-70W]/670mA -1 x 

EVG50–70W/760mA -1 x x 

EVG2x[50-70W]/760mA -1 xx 

EVG65–80W/880mA -1 x x x 

EVG2x[65-80W]/880mA -1 x x x 

EVG150-200W/1A -1 x 

EVG100-150W/1,5A -1 x x x x 

EVG150-200W/1,5A -1 x x 

EVG160-200W/2A -1 x x 

EVG240W/2A -1 x x x 

EVG300W/2,1A -1 

24V DC, rapid start, 4-pin 

x 

EVG11-20W/425mA -4 xx x 

EVG36W/425mA -4 

230V, instant start, 2-pin 

x x 

ST-EVG 11/20 IS x x x 

EVG11-20W/425mA IS xx x 

S-EVG30-50W/425mA IS x x x 

EVG2x[30-50W]/425mA IS x x x 

S-EVG50-70W/425mA IS x x 

EVG2x[50-70W]/425mA IS x x 

S-EVG35-45W/610mA IS x 

EVG2x[35-45W]/610mA IS x 

EVG4x[20W]/425mA IS x 

EVG4x[40W]/425mA IS x x x 

S-EVG50-70W/760mA IS x x 

EVG2x[50-70W]/760mA IS xx 

see next page ⇒ 



S-EVG65-80W/880mA IS x 

EVG2x[65-80W]/880mA IS x 

EVG4x[150W]/1A IS x x 

EVG150-200W/1A IS x 

EVG2x[150-200W]/1A IS x 

115V, instant start, 2-pin 

EVG11-20W/425mA IS x x x 

S-EVG30-50W/425mA IS-1 x x x 

EVG2x[30–50W]/425mA IS-1 x x x 

EVG50-70W/425mA IS-1 x x 

EVG2x[50–70W]/425mA IS-1 x x 

EVG35-45W/610mA IS-1 x 

EVG2x[35–45W]/610mA IS-1 x 

EVG50-70W/760mA IS-1 xx 

EVG2x[50–70W]/760mA IS-1 x x 

EVG65-80W/880mA IS-1 x x 

EVG2x[65–80W]/880mA IS-1 x x 

EVG150–200W/1A IS-1 x 

24V DC, rapid start, 4-pin 

EVG11-20W/425mA IS -4 xx x 

Special Design for LightSources Inc. / LightTech Lamp Technology Ltd. 

02/2007 

GPHA1000T5L 

GPHA1000T6L 

- 8 - 

GPHA1554T5L 

E230.101 x x x 

R(S)-E230.101 x 

E230.102 x 

R(S)-E230.102 x 

UV Compact MCplus E230.102 x 

E230.103 x 

R(S)-E230.103 x 


S-E230.104 x 

S-E230.107 x 

E230.108 x x 

E230.110 x x x 

R(S)-E230.110 x 


E230.201 x 

R(S)-E230.201 x 

E230.202 x 

R(S)-E230.202 x 

E230.203 x 

R(S)-E230.203 x 

E230.204 x 

E230.205 x x 

E230.207 x 

E230.208 x x 

E230.210 x x 

E230.211 x 

R(S)-E230.211 x 

GPHA1554T6L 

GPHA357T5L 

GPHA357T6L 

GPHA842T5L 

GPHA842T6L 

GPHHA1000T6L 

GPHHA1554T6L 

GPHHA357T6L 

GPHHA842T6L 



Special Lamp-Ballast Combinations 

G36T5 

G64T5 

GHO36T5 

GHO64T5 

GIA120 

GIA200 

GIA240 

GPH212T5L 

GPH287T5L 

GPH303T5L 

GPH356T5L 

GPH436T5HO 

GPH436T5L 

GPH793T5 

GPH846T5 

GPH846T5HO 

GPH893T5HO 

NNI120 

NNI200 

NNI201/107XL 

NNI300/147XL 

NNI400 

NNI60/25U 

NNI80/36U 























UNI120 

UNI200 

UNI201 

UNI260 

UNI40 

UNI60 



allast type C 

Available Ballasts 

09/2006 

ballast type A 

ballast type B 

ballast type O 

ballast name input voltage 

[V] 

*power supply requirements for 24V DC ballast: stabilised, short-circuit proof, inrush current 2A min. 


- 9 - 

input input power per 

power [W] current [A] lamp [W] 


Electronic Ballasts (4pin-type) 

EVG 11W...36W 

230V AC / 115V AC / 24V DC 

lamp 

current [A] 

ballast 

type 

suitable lamp types 

(manufacturer model) 

ST-EVG 11/20 230V AC ± 10% up to 24 0,05 - 0,11 11-20 0,425 ± 10% C 

EVG11-20W/425mA 

EVG11-20W/425mA -1 

230V AC ± 10% up to 24 

115V AC ± 10% up to 24 

0,05 - 0,11 

0,11 - 0,23 

11-20 

11-20 

0,425 ± 10% A 

0,425 ± 10% A 

TUV16, 

GPH287T5L, 

GPH303T5L 

EVG11-20W/425mA -4 24V* DC ± 10% up to 24 0,47 - 1,1 11-20 0,425 ± 10% B 

EVG18W/370mA 230V AC ± 10% 20 0,08 - 0,1 17 0,370 ± 10% A TUV18PLL 

EVG36W/425mA -4 24V* DC ± 10% up to 24 1,7 - 1,8 36 0,425 ± 10% O G36T5, TUV36T5 

mains frequency: 45...65Hz tc-temperature: max. 50°C CE-conform: yes 

operating frequency: 30...50kHz ambient temperature: 0...40°C efficiency: ca. 85% 

max. off-load voltage 

on terminals 1...4: 

type A: 1.5kVpp , type B: 600Vrms status indication: green and red LED indicate operating status, 

type C: buzzer sounds up if the lamp is not working 

photocoupler, max. current on OG: 5mA (open collector VOG1/0


ballast name input power 

[W] 

Ballasts for two lamps are also working if only one lamp is connected. 

09/2006 

ballast type D 

ballast type F 

- 10 - 

input 

current [A] 

lamps per 

ballast 

power per 

lamp [W] 

lamp 

current [A] 

ballast 

type 



EVG 30...90W / 230V AC 

ballasts for one and for two lamp operation available 



S-EVG30-50W/425mA 32 - 55 0,13 - 0,26 1 30 - 50 0,39 - 0,42 D G36T5, GPH793T5, TUV25, 

TUV36T5, GPH846T5 

EVG2x[30-50W]/425mA up to 110 0,25 - 0,53 2 30 - 50 0,39 - 0,42 F G36T5, GPH793T5, TUV25, 


S-EVG50-70W/425mA 55 – 75 0,26 - 0,36 1 50 - 70 0,39 - 0,42 D G64T5, TUV64T5 

EVG2x[50-70W]/425mA up to 150 0,43 - 0,72 2 50 - 70 0,39 - 0,42 F G64T5, TUV64T5 

S-EVG36W/440mA 40 0,16 - 0,19 1 36 0,44 D TUV36, TUV36PLL 

EVG2x[36W]/440mA up to 80 0,32 - 0,38 2 36 0,44 F TUV36, TUV36PLL 

S-EVG35-45W/610mA 38 – 50 0,15 - 0,24 1 35 - 45 0,6 - 0,62 D GPH436T5HO 

EVG2x[35-45W]/610mA up to 100 0,3 - 0,48 2 35 - 45 0,6 - 0,62 F GPH436T5HO 

S-EVG50-70W/670mA 55 – 75 0,26 - 0,36 1 50 - 70 0,65 - 0,7 D NNI60/25U, TUV60PLL 

EVG2x[50-70W]/670mA up to 150 0,43 - 0,72 2 50 - 70 0,65 - 0,7 F NNI60/25U, TUV60PLL 

S-EVG50-70W/760mA 55 – 75 0,26 - 0,36 1 50 - 70 0,75 - 0,77 D GPH846T5HO, 

GPH893T5HO, TUV55 

EVG2x[50-70W]/760mA up to 150 0,43 - 0,72 2 50 - 70 0,75 - 0,77 F GPH846T5HO, 

GPH893T5HO, TUV55 

S-EVG65-80W/880mA 70 – 85 0,28 - 0,4 1 65 - 80 0,85 - 0,9 D TUV75, GHO36T5, 


EVG2x[65-80W]/880mA up to 170 0,55 - 0,8 2 65 - 80 0,85 - 0,9 F TUV75, GHO36T5, 


S-EVG90W/950mA 100 0,4 - 0,48 1 90 0,95 D TUV95WHOPLL 

EVG2x[90W]/950mA up to 200 0,8 - 0,97 2 90 0,95 F TUV95WHOPLL 

S-EVG40-60W/1,2A 44 – 65 0,17 - 0,31 1 40 - 60 1 - 1,2 D UNI40, UNI60 

EVG2x[40–60W]/1,2A up to 130 0,34 - 0,62 2 40 - 60 1 - 1,2 F UNI40, UNI60 


mains voltage: 230V AC ± 10% CE-conform: yes efficiency: > 90% 

mains frequency: 45...65Hz tc-temperature: max. 50°C 

operating frequency: 30...50kHz ambient temperature: 0...40°C 

status indication: green and red LED indicate operating status 

potential free relay contact, 

type D load: 50...200mA at 24...230V AC; 50...500mA at 5V...60V DC 

type F load: 50...200mA at 24...120V AC; 50...500mA at 5V...60V DC 

wire gauge: type D: 0,5...1mm², type F: 0,75...1,5mm² (type F: max. 0,75mm² for potential free relay contacts) 

mounting restrictions: upright, mains connector at bottom side, see manual for details 

Please contact us if your lamp requires other technical data. We are able to adapt lamp and ballast in most cases. 





[W] 

Ballasts for two lamps are also working if only one lamp is connected. 

09/2006 

ballast type E 

ballast type G 

- 11 - 

input 

current [A] 

lamps per 

ballast 

power per 

lamp [W] 

lamp 

current [A] 

ballast 

type 



EVG 100...200W / 230V AC 




EVG130W/2,1A 140 - 150 0,56 - 0,75 1 130 - 140 2 - 2,1 E TUV130XPT 

EVG2x[130W]/2,1A up to 300 1,12 - 1,5 2 130 - 140 2 - 2,1 G TUV130XPT 

EVG150-200W/1A 160 – 220 0,65 - 1,0 1 150 - 200 0,8 – 1 E GHO64T5, TUV64T5HO 

EVG2x[150-200W]/1A up to 440 1,7 - 2,1 2 150 - 200 0,8 - 1 G GHO64T5, TUV64T5HO 

EVG100-150W/1,5A 110 - 160 0,43 - 0,77 1 100 -150 1,4 - 1,5 E NNI80/36U, NNI120, UNI120, 

GIA120, TUV115 

EVG2x[100-150W]/1,5A up to 300 0,87 - 1,3 2 100 -150 1,4 - 1,5 G NNI80/36U, NNI120, UNI120, 

GIA120, TUV115 

EVG150-200W/1,5A 160 – 220 0,65 - 1,0 1 150 - 200 1,4 - 1,5 E GIA200, UNI201 

EVG2x[150-200W]/1,5A up to 440 1,7 - 2,1 2 150 - 200 1,4 - 1,5 G GIA200, UNI201 

EVG160-200W/2A 175 – 220 0,7 - 1,1 1 160 - 200 1,85 – 2 E NNI200, UNI200, NNI201/107XL 

EVG2x[160-200W]/2A up to 440 1,7 - 2,1 2 160 - 200 1,85 - 2 G NNI200, UNI200 





efficiency: > 90% 



load: 50...200mA at 24...120V AC; 50...500mA at 5...60V DC 

wire gauge: 0,75...1,5mm² 







[W] 

ballast type H: also available as PREHEAT START version on request 

(add -PH to ballast name), 

2-STEP DIMMING on request (add -SD to ballast name) 

ballast type I: 4-STEP DIMMING is not standard 

⇒ implementation on request (add -SD to ballast name) 

ballasts for two lamps are also working if only one lamp is connected 

09/2006 

ballast type H 

ballast type I 

- 12 - 

input 

current [A] 

lamps per 

ballast 

power per 

lamp [W] 

lamp 

current [A] 

ballast 

type 



EVG 200...400W / 230V AC 

ballasts for one and for two lamp operation available, 

PREHEAT START versions available on request (only for one lamp ballast type H) 



EVG2x[220W]/2A 440 - 480 1,74 - 2,31 2 200 - 220 1,9 - 2,2 I NNI201/107XL 

EVG240W/2A 250 - 280 0,99 - 1,35 1 220 - 250 1,9 - 2,2 H UNI260, GIA240, TUV240WXPT 

EVG2x[240W]/2A 500 - 560 1,98 - 2,7 2 220 - 250 1,9 - 2,2 I UNI260, GIA240, TUV240WXPT 

EVG270W/3,8A 280 - 310 1,1 – 1,5 1 250 -280 3,6 - 4,0 H TUV260XPT, TUV270XPT 

EVG2x[270W]/3,8A 560 - 620 2,21 - 3 2 250 -280 3,6 - 4,0 I TUV260XPT, TUV270XPT 

EVG300W/2,1A 350 1,38 - 1,7 1 320 2,1 - 2,4 H NNI300/147XL 

EVG2x[300W]/2,1A 700 2,76 - 3,38 2 320 2,1 - 2,4 I NNI300/147XL 

EVG320W/2,2A 350 1,38 - 1,7 1 320 2,1 - 2,4 H TUV325XPT 

EVG2x[320W]/2,2A 700 2,76 - 3,38 2 320 2,1 - 2,4 I TUV325XPT 

EVG400W/3,8A 425 1,7 - 2,1 1 400 3,8 H NNI400 

EVG330W/4,8A 370 1,46 - 1,79 1 330 4,8 H TUV330XPT 








load: 50...200mA at 24...230V AC; 50...500mA at 5...60V DC 



4-STEP DIMMING scheme 

lamp A/B current 100% 90% 80% 70% 

DM 1 A/B 0 0 12V DC 12V DC 

DM 0 A/B 0 12 V DC 0 12V DC 

current approx. 1mA @ 12V DC (voltage range: 9-25V DC) 




allast type R 

ballast type S 

ballast type T 

ballast type U 

Features 

• electronic ballasts as plug-in cards for rack 

mounting 

• preheat start implemented 

• all connections (mains, lamp and control 

voltage, error control) routed through a 

MOLEX JUNIOR FIT connector 

• microprocessor controlled 

09/2006 

- 13 - 



as plug-in cards for rack mounting, microprocessor controlled 

R-EVG 200...400W (with RS485: RS-EVG 200...400W) / 230V AC 

• type R, S (without RS485): 

• to be switched on and off externally by 

12V...24 DC control voltage 

• potential free relay contact for fault 

indication 

ballasts for one and two lamp operation available, 

PREHEAT START implemented 

• type T, U (with RS485): 

• switch-on/-off, dimming and status 

indication via RS485 

• addressable with DIP-switch 

up to 1023 

• preheat parameters programmable 

• dimmable on request 





[W] 


09/2006 

- 14 - 



as plug-in cards for rack mounting, microprocessor controlled 

R-EVG 200...400W (with RS485: RS-EVG 200...400W) / 230V AC 

input 

current [A] 

Available Ballasts for Lightsources Inc. / LightTech Lamp Technology Ltd. 


mains voltage: 230V AC ± 10% mains frequency: 45...65Hz 

ambient temperature: 0...40°C tc-temperature: max. 50°C 

operating frequency: 25...70kHz efficiency: > 90% 

control voltage: 12...24V DC (contacts optically isolated) 

ballasts for one and two lamp operation available, 

PREHEAT START implemented 


type R, S: potential free relay contact, load: 50...200mA at 24...230V AC; 50...500mA at 5...60V DC 

type T, U: RS485 for status indication and controlling 

mounting restrictions: rack mounting with forced cooling, see manual for details 

connections: to be used with MOLEX JUNIOR 

FIT connector 15-06-0241 

lamps per 

ballast 

power per 

lamp [W] 

lamp 

current [A] 


ballast 

type 



R-EVG2x[220W]/2A 440 - 480 1,74 - 2,31 2 200 - 220 1,9 - 2,2 S NNI201/107XL 

RS-EVG2x[220W]/2A 440 - 480 1,74 - 2,31 2 200 - 220 1,9 - 2,2 U NNI201/107XL 

R-EVG240W/2A 250 - 280 0,99 - 1,35 1 220 - 250 1,9 - 2,2 R UNI260, GIA240, TUV240WXPT 

RS-EVG240W/2A 250 - 280 0,99 - 1,35 1 220 - 250 1,9 - 2,2 T UNI260, GIA240, TUV240WXPT 

R-EVG2x[240W]/2A 500 - 560 1,98 - 2,7 2 220 - 250 1,9 - 2,2 S UNI260, GIA240, TUV240WXPT 

RS-EVG2x[240W]/2A 500 - 560 1,98 - 2,7 2 220 - 250 1,9 - 2,2 U UNI260, GIA240, TUV240WXPT 

R-EVG270W/3,8A 280 - 310 1,1 – 1,5 1 250 -280 3,6 - 4,0 R TUV260XPT, TUV270XPT 

RS-EVG270W/3,8A 280 - 310 1,1 – 1,5 1 250 -280 3,6 - 4,0 T TUV260XPT, TUV270XPT 

R-EVG2x[270W]/3,8A 560 - 620 2,21 - 3 2 250 -280 3,6 - 4,0 S TUV260XPT, TUV270XPT 

RS-EVG2x[270W]/3,8A 560 - 620 2,21 - 3 2 250 -280 3,6 - 4,0 U TUV260XPT, TUV270XPT 

R-EVG300W/2,1A 350 1,38 - 1,7 1 320 2,1 - 2,4 R NNI300/147XL 

RS-EVG300W/2,1A 350 1,38 - 1,7 1 320 2,1 - 2,4 T NNI300/147XL 

R-EVG2x[300W]/2,1A 700 2,76 - 3,38 2 320 2,1 - 2,4 S NNI300/147XL 

RS-EVG2x[300W]/2,1A 700 2,76 - 3,38 2 320 2,1 - 2,4 U NNI300/147XL 

R-EVG320W/2,2A 350 1,38 - 1,7 1 320 2,1 - 2,4 R TUV325XPT 

RS-EVG320W/2,2A 350 1,38 - 1,7 1 320 2,1 - 2,4 T TUV325XPT 

R-EVG2x[320W]/2,2A 700 2,76 - 3,38 2 320 2,1 - 2,4 S TUV325XPT 

RS-EVG2x[320W]/2,2A 700 2,76 - 3,38 2 320 2,1 - 2,4 U TUV325XPT 

R-EVG400W/3,8A 425 1,7 - 2,1 1 400 3,8 R NNI400 

RS-EVG400W/3,8A 425 1,7 - 2,1 1 400 3,8 T NNI400 

R-EVG330W/4,8A 370 1,46 - 1,79 1 330 4,8 R TUV330XPT 

RS-EVG330W/4,8A 370 1,46 - 1,79 1 330 4,8 T TUV330XPT 

lamp type lamp watts [W] lamps per 

ballast 

ballast models ballast power 

[W]* 

ballast input 

current [A] 

GPHA1554T5L 196 1 R-E230.101 216 0,95 R 

GPHA1554T5L 196 1 RS-E230.101 216 0,95 T 

GPHA1554T5L 196 2 R-E230.201 432 1,8 S 

GPHA1554T5L 196 2 RS-E230.201 432 1,8 U 

GPHA1554T6L 240 1 R-230.102 261 1,14 R 

GPHA1554T6L 240 1 RS-230.102 261 1,14 T 

GPHA1554T6L 240 2 R-230.202 520 2,38 S 

GPHA1554T6L 240 2 RS-230.202 520 2,38 U 

GPHHA1000T6L 207 1 R-E230.110 218 0,96 R 

GPHHA1000T6L 207 1 RS-E230.110 218 0,96 T 

GPHHA1000T6L 207 2 R-E230.211 440 2 S 

GPHHA1000T6L 207 2 RS-E230.211 440 2 U 

GPHHA1554T6L 320 1 R-E230.103 340 1,52 R 

GPHHA1554T6L 320 1 RS-E230.103 340 1,52 T 

GPHHA1554T6L 320 2 R-E230.203 680 3,04 S 

GPHHA1554T6L 320 2 RS-E230.203 680 3,04 U 

ballast type 






[W] 

09/2006 

ballast type K 

ballast type N 

- 15 - 

input 

current [A] 

lamps per 

ballast 

power per 

lamp [W] 

lamp 

current [A] 

ballast 

type 



microprocessor controlled 

200...350W/1,9...2,1A up to 500...900W/4...11A / 230V AC 

ballasts for one and two lamp operation for use with Digital Operation System 



P-EVG2x[240W]/2A 440 - 500 1,74 - 2,42 2 220 -250 1,9 - 2,2 K UNI260, GIA240, 


P-EVG2x[300W]/2,1A 700 2,56 - 3,2 2 320 2,1 - 2,4 K NNI300/147XL 

P-EVG800W/7A 890 3,5 - 4,3 1 800 4 - 7 N 

P-EVG800W/11A 890 3,5 - 4,3 1 800 7 - 11 N 

Functions: 

• preheat start 

• switch-on current = operating current 

• input voltage control 

• undervoltage switch-off 


serial port control features: 

• connection of up to 256 devices via RS485, 

loop through possible 

• switch-on/-off 

• dimming: 50...100% with current 

compensation in the lamps filaments 

• preheating 

(cable-length compensation) 

• internal hourmeter 

• adjustment of several parameters 

• status readout 





status indication: green, yellow and red LED indicate operating status 

error code 

bus communication 



Readout: 

• status (errors) 

• correct connection 

• lamp power 

• lamp voltage 

• dimming status 

• filament status 

• operation hours 




09/2006 






- 16 - 



EVG 30...300W / 115V AC 












[W] 

ballast type H: also available as PREHEAT START version on request (add -PH to ballast name), 

ballasts for two lamps are also working if only one lamp is connected. 

09/2006 

- 17 - 

input 

current [A] 

lamps per 

ballast 

power per 

lamp [W] 

lamp 

current [A] 

ballast 

type 



EVG 30...300W / 115V AC 





type D, H load: 50...200mA at 24...230V AC; 50...500mA at 5...60V DC 

type E, F, G load: 50...200mA at 24...120V AC; 50...500mA at 5...60V DC 

wire gauge: type D: 0,5...1mm² / type E, F, G, H: 0,75...1,5mm² 

(type F: max. 0,75mm² for potential free relay contacts) 




S-EVG30–50W/425mA -1 32 - 55 0,25 - 0,53 1 30 - 50 0,39 - 0,42 D G36T5, GPH793T5, 


EVG2x[30-50W]/425mA -1 up to 110 0,5 - 1,05 2 30 - 50 0,39 - 0,42 F G36T5, GPH793T5, 


EVG50–70W/425mA -1 55 – 75 0,43 - 0,72 1 50 - 70 0,39 - 0,42 E G64T5, TUV64T5 

EVG2x[50-70W]/425mA -1 up to 150 0,86 - 1,4 2 50 - 70 0,39 - 0,42 F G64T5, TUV64T5 

S-EVG35–45W/610mA -1 38 – 50 0,3 - 0,48 1 35 - 45 0,6 - 0,62 D GPH436T5HO 

EVG2x[35-45W]/610mA -1 up to 100 0,6 - 0,96 2 35 - 45 0,6 - 0,62 F GPH436T5HO 

EVG50–70W/670mA -1 55 – 75 0,43 - 0,72 1 50 – 70 0,65 – 0,7 E NNI60/25U 

EVG2x[50-70W]/670mA -1 up to 150 0,86 - 1,4 2 50 – 70 0,65 - 0,7 F NNI60/25U 

EVG50–70W/760mA -1 55 – 75 0,43 - 0,72 1 50 – 70 0,75 - 0,77 E GPH846T5HO, GPH893T5HO 

EVG2x[50-70W]/760mA -1 up to 150 0,86 - 1,4 2 50 – 70 0,75 - 0,77 F GPH846T5HO, GPH893T5HO 

EVG65–80W/880mA -1 70 – 85 0,55 - 0,8 1 65 – 80 0,85 – 0,9 E TUV36HO, TUV75, 

GHO36T5 

EVG2x[65-80W]/880mA -1 up to 170 1,1 - 1,6 2 65 – 80 0,85 - 0,9 G TUV36HO, TUV75, 

GHO36T5 

EVG150-200W/1A -1 160 – 220 1,26 - 2,1 1 150 0,8 - 1 E GHO64T5 

EVG100-150W/1,5A -1 110 - 160 0,86 - 1,55 1 100 - 150 1,4 - 1,5 E NNI80/36U, NNI120, 

UNI120, GIA120, TUV115 

EVG150-200W/1,5A -1 160 – 220 1,26 - 2,1 1 150 - 200 1,4 - 1,5 H GIA200, UNI201 

EVG160-200W/2A -1 175 – 220 1,4 - 2,1 1 160 - 200 1,85 – 2 H NNI200, NNI201, UNI200 

EVG240W/2A -1 250 - 280 2,0 - 2,7 1 220 - 250 1,9 - 2,2 H UNI260, GIA240, 


EVG300W/2,1A -1 350 2,76 - 3,38 1 320 2,1 - 2,4 H NNI300/147XL 




Lamp Type Selection 

*values are depending on the temperature conditions of the lamps 

ballast type H: also available as PREHEAT START version on request, two step dimming on request 

09/2006 




- 18 - 


lamp type lamp watts [W] ballast models ballast power [W]* ballast input current ballast type 

[A] 

GPHA357T5L 42 S-E230.104 50 0,25 D 

GPHA842T5L 105 E230.101 118 0,53 E 

GPHA1000T5L 127 E230.101 140 0,62 E 

GPHA1554T5L 196 E230.101 216 0,95 E 

GPHA357T6L 57 S-E230.107 68 0,32 D 

GPHA842T6L 127 E230.108 140 0,62 E 

GPHA1000T6L 150 E230.108 164 0,74 E 

GPHA1554T6L 240 E230.102 261 1,14 H 

GPHHA357T6L 65 E230.110 74 0,35 E 

GPHHA842T6L 172 E230.110 180 0,79 E 

GPHHA1000T6L 207 E230.110 218 0,96 E 

GPHHA1554T6L 320 E230.103 340 1,52 H 

Technical Data 

mains voltage: 230V AC ± 10%, min. 

mains voltage 192V AC 

CE-conform: yes efficiency: > 90% 



lamp fault indicator: green and red LED indicate operating status 


type E load: 50...200mA at 24...120V AC; 50...500mA at 5...60V DC 

type D, H load: 50...200mA at 24...230V AC; 50...500mA at 5...60V DC 


wire gauge: type D: 0,5...1mm², type E,H: 0,75...1,5 mm² 

Single Electronic Ballasts for Amalgam Lamps 

Special Design E230.1** 

for LightSources Inc. / LightTech Lamp Technology Ltd. 



09/2006 



ballast type I 

*values are depending on the temperature conditions of the lamps 


- 19 - 


Twin Electronic Ballasts for Amalgam Lamps 

Special Design E230.2** 

for LightSources Inc. / LightTech Lamp Technology Ltd. 

Lamp Type Selection 

lamp type lamp watts ballast ballast power ballast input ballast type 

[W] 

models [W]* 

current [A] 

GPHA357T5L 42 E230.204 100 0,5 F 

GPHA842T5L 105 E230.205 236 1,04 G 

GPHA1000T5L 127 E230.205 280 1,24 G 

GPHA1554T5L 196 E230.201 432 1,8 G 

GPHA357T6L 57 E230.207 136 0,66 F 

GPHA842T6L 127 E230.208 280 1,24 G 

GPHA1000T6L 150 E230.208 328 1,48 G 

GPHA1554T6L 240 E230.202 520 2,38 I 

GPHHA357T6L 65 E230.210 148 0,7 F 

GPHHA842T6L 172 E230.210 360 1,64 G 

GPHHA1000T6L 207 E230.211 440 2 I 

GPHHA1554T6L 320 E230.203 680 3,04 I 

For type I ballasts 

step dimming is possible: 

Dimming 

DM1A DM0A lamp 

current 

0 0 100 % 

0 12 V DC 90 % 

12 V DC 0 80 % 

12 V DC 12 V DC 70 % 

Same diagram for lamp B, 

current approx. 1mA @ 12V DC 

(voltage range: 9-25V DC) 

Technical Data 

mains voltage: 230V AC ± 10%, min. 

mains voltage 192V AC 

CE-conform: yes efficiency: > 90% 



lamp fault indicator: green and red LED indicate operating status 


type F, G load: 50...200mA at 24...120V AC; 50...500mA at 5...60V DC 

type I load: 50...200mA at 24...230V AC; 50...500mA at 5...60V DC 


wire gauge: 0,75...1,5 mm² (type F: max. 0,75 mm² for terminal 4-9, type I : 0,35...0,5 mm² for terminal 4-9 and 14-19) 



allast name input power 

[W] 

09/2006 

- 20 - 

input current 

[A] 

lamp power 

[W] 

lamp current 

[A] 


lamp type 

UV-Compact MC 30-50W/425mA OS 35 - 55 0,13 - 0,22 30 - 50 0,39 - 0,42 G36T5, GPH793T5, TUV25, 


UV-Compact MC 50-70W/425mA OS 55 - 80 0,22 - 0,3 50 - 70 0,39 - 0,42 G64T5, TUV64T5 

UV-Compact MC 35-45W/610mA OS 40 - 50 0,15 - 0,2 35 - 45 0,6 - 0,62 GPH436T5HO 

UV-Compact MC 50-70W/670mA OS 55 - 80 0,22 - 0,3 50 - 70 0,65 - 0,7 NNI60/25U, TUV60PLL 

UV-Compact MC 50-70W/760mA OS 55 - 80 0,22 - 0,3 50 - 70 0,75 - 0,77 GPH846T5HO, GPH893T5HO, 


UV-Compact MC 65-80W/880mA OS 70 - 90 0,28 - 0,35 65 - 80 0,85 - 0,9 GHO36T5, TUV36HO, TUV75 

UV-Compact MC 150-200W/1A OS 160 – 220 0,65 - 0,9 150 - 200 0,8 – 1 GHO64T5, TUV64T5HO 

UV-Compact MC 40-60W/1,2A OS 45 - 65 0,17 - 0,26 40 - 60 1 - 1,2 UNI40, UNI60 

UV-Compact MC 100-150W/1,5A OS 110 - 170 0,43 - 0,65 100 - 150 1,4 - 1,5 GIA120, NNI120, NNI80/36U, 

UNI120 

UV-Compact MC 150-200W/1,5A OS 160 - 220 0,65 - 0,87 150 - 200 1,4 - 1,5 GIA200, UNI201 

UV-Compact MC 160-200W/2A OS 180 - 220 0,7 - 0,87 160 - 200 1,85 - 2 NNI200, UNI200 

Features 

• integrated electronic ballast 

for uv-lamps 

• hour counter 

• temperature monitoring 

• synchronous readout of state, 

operating hours, time and date 

• multicolour backlighting 

(red, green, yellow) for additional 

status-indication 

• menu lock 



mains frequency: 45...65Hz ambient 

temperature: 

0...40°C 


display: 4*20 digits, green, yellow or red back lighting for status indication, adjustment of contrast by menu 

handling: menu-driven handling and programming by 4 push-buttons 

language: alternatively English or German (other languages on request) 

dimensions (w/h/l): (190/72/180)mm weight: 1900g 

connections: mains: line cord, cable length 2m 

Electronic Ballast with Integrated Hour Counter, 

Multicolour Display 

UV-Compact MC 30...200W OS, 230V AC 

hour counter: 

• internal real time clock 

• global hour counter 

• switch cycle counter 

• programmable user hour counter 

• adjustable end of lamp lifetime alarm 

temperature monitoring: 

• measurement of internal temperature 

• internal temperature 

can be monitored via menu 

• message ’’internal overheating’’ and 

system shutdown in case of 

temperature above 

certain switching thresholds 

• automatic restart 

can be defined by customer 

lamp: Hirschmann cable socket CA6GD 

(Hirschmann cable plug CA6LS is element of delivery, see drawing for connector pin list) 

protective earth: cable green/yellow, length 2m 

protection class: IP54 if lamp is connected by appropriated plug 

for use in one-lamp systems 

Please note the technical advices and the installation and operating instructions in the UV-Compact MC - Documentation. 

For use in chemical and biological inactive environment only! To be installed by specialized staff. 




[W] 

09/2006 

- 21 - 

input current 

[A] 

lamp power 

[W] 

lamp current 

[A] 


lamp type 

UV-Compact MC 30-50W/425mA 35 - 55 0,13 - 0,22 30 - 50 0,39 - 0,42 G36T5, GPH793T5, TUV25, 


UV-Compact MC 50-70W/425mA 55 - 80 0,22 - 0,3 50 - 70 0,39 - 0,42 G64T5, TUV64T5 

UV-Compact MC 35-45W/610mA 40 - 50 0,15 - 0,2 35 - 45 0,6 - 0,62 GPH436T5HO 

UV-Compact MC 50-70W/670mA 55 - 80 0,22 - 0,3 50 - 70 0,65 - 0,7 NNI60/25U, TUV60PLL 

UV-Compact MC 50-70W/760mA 55 - 80 0,22 - 0,3 50 - 70 0,75 - 0,77 GPH846T5HO, GPH893T5HO, 


UV-Compact MC 65-80W/880mA 70 - 90 0,28 - 0,35 65 - 80 0,85 - 0,9 GHO36T5, TUV36HO, TUV75 

UV-Compact MC 150-200W/1A 160 – 220 0,65 - 0,9 150 - 200 0,8 – 1 GHO64T5, TUV64T5HO 

UV-Compact MC 40-60W/1,2A 45 - 65 0,17 - 0,26 40 - 60 1 - 1,2 UNI40, UNI60 

UV-Compact MC 100-150W/1,5A 110 - 170 0,43 - 0,65 100 - 150 1,4 - 1,5 GIA120, NNI120, NNI80/36U, 

UNI120 

UV-Compact MC 150-200W/1,5A 160 - 220 0,65 - 0,87 150 - 200 1,4 - 1,5 GIA200, UNI201 

UV-Compact MC 160-200W/2A 180 - 220 0,7 - 0,87 160 - 200 1,85 - 2 NNI200, UNI200 

Features 




• uv-value monitoring 

• synchronous readout of 

• uv-value, uv-state, operating hours, 

time and date 

• multicolour backlighting (red, green, 

yellow) for additional status-indication 

• menu lock 

Electronic Ballast with Integrated Hour Counter and UV-Monitor, 

Multicolour Display 

UV-Compact MC 30...200W, 230V AC 

hour counter: 


• global hour/switch cycle counter 





• internal temperature 

can be monitored via menu 


system shutdown in case of 




temperature: 

0...40°C 








temperature above 

certain switching thresholds 

• automatic restart 

can be defined by customer 

UV-value monitoring: 

• to be enabled/disabled by customer 

• relative uv-intensity (in %) 

• adjustable uv-low alarm 

(two steps: pre alarm - yellow / 

main alarm - red backlighting) 

• automatic adjustment of sensitivity 

uv-sensor: sensor cable, length 1m, with Hirschmann cable plug ELST 5012 (see drawing for connector pin list) 

lamp: Hirschmann cable socket CA6GD 

(Hirschmann cable plug CA6LS is element of delivery, see drawing for connector pin list) 


protection class: IP54 if lamp and sensor are connected by appropriated plugs 

recommended 

SiC001-uv-compact, SiC003-uv-compact, SiC007-P-uv-compact with measurement window MF001 

sensor types: 

Please note the technical advices and the installation and operating instructions in the UV-Compact MC - Documentation. 





[W] 

09/2006 

- 22 - 

input current 

[A] 

lamp power 

[W] 

lamp current 

[A] 


Electronic Ballast with Integrated Hour Counter and UV-Monitor 

Multicolour Display, Active Cooling 

UV-Compact MCplus 200...350W, 230V AC 

lamp type 

UV Compact MCplus 200W/2A 220 0,79 - 0,97 200 1,85 - 2 NNI201/107XL 

UV Compact MCplus 240W/2A 270 - 310 0,87 - 1,21 250 - 280 1,9 - 2,2 GIA240, UNI260 

UV Compact MCplus 300W/2,1A 360 1,28 - 1,6 320 2,1...2,4 NNI300/147XL 

UV Compact MCplus 320W/2,2A 360 1,28 - 1,6 320 2,1...2,4 TUV325XPT 

UV Compact MCplus E230.111 218 0,86 - 1,05 207 GPHHA1000T6L 

UV Compact MCplus E230.102 261 1,03 - 1,26 240 GPHA1554T6L 

UV Compact MCplus E230.103 340 1,34 - 1,64 320 GPHHA1554T6L 

Features 


for uv-lamps 


• uv-value monitoring 


• integrated fan for active cooling 

• synchronous readout 

of uv-value, uv-state, operating 

hours, time and date 

• multicolour backlighting 

(red, green, yellow) for additional 

status-indication 

• menu lock 

hour counter: 


• global hour counter 

• switch cycle counter 



UV-value monitoring: 

• to be enabled/disabled by customer 


• adjustable uv-low alarm (two steps: 

pre alarm/main alarm 

• automatic adjustment of sensitivity 




(optional external temperature) 

• internal temperature can be monitored 

via menu 


system shutdown in case of temperature 

above certain switching thresholds 

• automatic restart can be defined by 

customer 




temperature: 

0...40°C 







uv-sensor: BNC-socket 

protection class: 

lamp: 4wire lamp cable, length 2m provided with 4pin ceramic type lamp socket 


IP00 

recommended 

SiC001-PG-BNC, SiC003-PG-BNC, SiC007-P-PG-BNC with measurement window MF001, 

sensor types: 

SLS-SiC003-PG-BNC, SLS-SiC004-PG-BNC 

(2wire cable with BNC-connector, shielded, length 2,0m) 

Please note the technical advices and the installation and operating instructions in the UV-Compact MCplus - Documentation. 




09/2006 

ballast type A 

ballast type B 



ballast type C 

ballast name input voltage 

[V] 

- 23 - 

input input power per 

power [W] current [A] lamp [W] 

*power supply requirements for 24V DC ballast: stabilised, short-circuit proof, inrush current 1,5A min. 



EVG 11W...20W 

230V AC / 115V AC / 24V DC 

lamp 

current [A] 

ST-EVG 11/20 IS 230V AC ± 10% up to 24 0,05 - 0,11 11-20 0,425 ± 10% C 

EVG11-20W/425mA IS 230V AC ± 10% up to 24 0,05 - 0,11 11-20 0,425 ± 10% A 

EVG11-20W/425mA IS -1 115V AC ± 10% up to 24 0,11 - 0,23 11-20 0,425 ± 10% A 

EVG11-20W/425mA IS -4 24V* DC ± 10% up to 24 0,47 - 1,1 11-20 0,425 ± 10% B 

ballast 

type 



TUV16, 

GPH287T5L, 

GPH303T5L 

mains frequency: 45...65Hz tc-temperature: max. 50°C CE-conform: yes 

operating frequency: 30...50kHz ambient temperature: 0...40°C efficiency: ca. 85% 

max. off-load voltage 

on terminals 1...4: 

type A: 1.5kVpp , type B: 600Vrms status indication: green and red LED indicate operating status, 

type C: buzzer sounds up if the lamp is not working 

photocoupler, max. current on OG: 5mA (open collector VOG1/0

02/2007 





ballast type J 

(4 lamp - ballast) 

- 24 - 



EVG 20...200W / 230V AC, instant start 

ballasts for one, two and four lamp operation available 





[W] 

02/2007 

ballast type L 

- 25 - 

input 

current [A] 

lamps per 

ballast 




ballasts for one, two and four lamp operation available 

power per 

lamp [W] 

lamp 

current [A] 

ballast 

type 



S-EVG30-50W/425mA IS 35 - 55 0,14 - 0,26 1 30 - 50 0,39 - 0,42 D G36T5, GPH793T5, 


EVG2x[30-50W]/425mA IS up to 110 0,28 - 0,52 2 30 - 50 0,39 - 0,42 F G36T5, GPH793T5, 


S-EVG50-70W/425mA IS 55 – 75 0,22 - 0,36 1 50 - 70 0,39 - 0,42 D G64T5, TUV64SPT5 

EVG2x[50-70W]/425mA IS up to 160 0,44 - 0,7 2 50 - 70 0,39 - 0,42 F G64T5, TUV64SPT5 

S-EVG35-45W/610mA IS 38 – 50 0,15 - 0,24 1 35 - 45 0,6 - 0,62 D GPH436T5HO 

EVG2x[35-45W]/610mA IS up to 100 0,3 - 0,48 2 35 - 45 0,6 - 0,62 F GPH436T5HO 

EVG4x[20W]/425mA IS up to 85 0,33 - 0,41 4 20 0,42 J GPH436T5L 

EVG4x[40W]/425mA IS up to 170 0,65 - 0,8 4 35 0,42 J G36T5, GPH793T5, 

TUVSP36T5 

S-EVG50-70W/760mA IS 55 – 75 0,22 - 0,36 1 50 - 70 0,75 - 0,77 D GPH846T5HO, GPH893T5HO 

EVG2x[50-70W]/760mA IS up to 150 0,44 - 0,7 2 50 - 70 0,75 - 0,77 F GPH846T5HO, GPH893T5HO 

S-EVG65-80W/880mA IS 70 – 85 0,28 - 0,41 1 65 - 80 0,85 - 0,9 D TUV36HO, GHO36T5 

EVG2x[65-80W]/880mA IS up to 170 0,56 - 0,8 2 65 - 80 0,85 - 0,9 F TUV36HO, GHO36T5 

EVG4x[150W]/1A IS up to 650 2,6 - 3,1 4 150 0,8 - 1,0 L TUV64T5HO, GHO64T5 

EVG150-200W/1A IS 165 – 220 0,65 - 0,97 1 150 - 200 0,8 - 1,0 E GHO64T5 

EVG2x[150-200W]/1A IS up to 440 1,3 - 1,9 2 150 - 200 0,8 - 1,0 G GHO64T5 

Ballasts for two or four lamps are also working if not all lamps are connected. 







type D, L load: 50...200mA at 24...230V AC; 50...500mA at 5...60V DC 

type E, F, G, J load: 50...200mA at 24...120V AC; 50...500mA at 5...60V DC 

wire gauge: type D: 0,5...1mm² / type E, F, G, J, L: 0,75...1,5mm² (max. 0,75mm² for potential free relay contacts) 





09/2006 






- 26 - 




ballasts for one and two lamp operation available 






type D load: 50...200mA at 24...230V AC; 50...500mA at 5...60V DC 

type E, F, G load: 50...200mA at 24...120V AC; 50...500mA at 5...60V DC 

wire gauge: type D: 0,5...1mm², type E, F, G: 0,75...1,5mm² (type F: max. 0,75mm² for potential free relay contacts) 


see next page for list of ballasts ⇒ 





[W] 

ballasts for two lamps are also working if only one lamp is connected. 

09/2006 

- 27 - 

input 

current [A] 

lamps per 

ballast 




power per 

lamp [W] 

ballasts for one and two lamp operation available 

lamp 

current [A] 

ballast 

type 



S-EVG30-50W/425mA IS-1 32 - 55 0,25 - 0,53 1 30 – 50 0,39 - 0,42 D G36T5, GPH793T5, 


EVG2x[30–50W]/425mA IS-1 up to 110 0,5 - 1,05 2 30 – 50 0,39 – 0,42 F G36T5, GPH793T5, 


EVG50-70W/425mA IS-1 55 – 75 0,43 - 0,72 1 50 – 70 0,39 - 0,42 E G64T5, TUV64T5 

EVG2x[50–70W]/425mA IS-1 up to 150 0,86 - 1,4 2 50 – 70 0,39 – 0,42 F G64T5, TUV64T5 

S-EVG35-45W/610mA IS-1 38 – 50 0,3 - 0,48 1 35 – 45 0,6 - 0,62 D GPH436T5HO 

EVG2x[35–45W]/610mA IS-1 up to 100 0,6 - 0,96 2 35 – 45 0,6 – 0,62 F GPH436T5HO 

EVG50-70W/760mA IS-1 55 – 75 0,43 - 0,72 1 50 – 70 0,75 - 0,77 E GPH846T5HO, GPH893T5HO 

EVG2x[50–70W]/760mA IS-1 up to 150 0,86 - 1,4 2 50 – 70 0,75 – 0,77 F GPH846T5HO, GPH893T5HO 

EVG65-80W/880mA IS-1 70 – 85 0,55 - 0,8 1 65 – 80 0,85 - 0,9 E TUV36HO, TUV75, 

GHO36T5 

EVG2x[65–80W]/880mA IS-1 up to 170 1,1 - 1,6 2 65 – 80 0,85 – 0,9 G TUV36HO, TUV75, 

GHO36T5 

EVG150–200W/1A IS-1 160 – 220 1,26 - 2,1 1 150 -200 0,8 – 1 E GHO64T5 





mains voltage: ESBS01-1: 115V AC ± 10% 

ESBS01: 230V AC ± 10% 

dimensions 

(w/h/l): 

device delay 

switch settings: 

09/2006 

- 28 - 


Accessories for Electronic Ballasts 

Starting Component ESBS01-1/ESBS01 

for delayed power-on of 4 electronic ballasts (delay time selectable from 0...12s) by DIP-switch), 

extensible up to 4 starting components/16 electronic ballasts by cascading 

mains frequency: 45...65Hz max. constant 

input current 

of ballasts 

(complete): 

(97/43/96) mm weight: 400g (0,881lbs) 

S1 on: 0s | S3 on: 8s 

S2 on: 4s | S4 on: 12s 

Example for wiring and switching: 

ballast switching 

time: 

ballast 1: device delay +0s | ballast 3: device delay +2s 

ballast 2: device delay +1s | ballast 4: device delay +3s 


Phone: ++49 (O) 3677 2O 59 259 - Fax: ++49 (O) 3677 2O 59 26O - url: www.z-e-d.com - E-Mail: info@z-e-d.com 

6A

09/2006 

- 29 - 

UV-Monitor PRO 2 

with status indication by LED 


with relay contacts and status indication by LED 





UV-Monitor PRO 10.4 

with relay contacts, status indication by LED and LCD 

and integrated hour counter 


with relay contacts, status indication by LCD 


synchronous readout of uv-value and operating hours 

LCD with green and red back lighting for status indication 









LCD with green and red back lighting for status indication 

UV-Monitor PRO 20 / PRO 20-S 

for analog and digital multi-sensoring 





Measurement Technique 

UV-Monitors - Overview 

for monitoring of the relative and/or absolute uv-intensity 



09/2006 

PRO2 

PRO3 

PRO5 

- 30 - 

PRO8 

PRO10.4 



Recommended Measurement Combinations 

of Sensors and Monitors 

Please note: We offer the adjustment of the sensors according to your requirements. 

PRO10.4-U2 

PRO10.4-SLS 

PRO11PI-I 

PRO11PU3-I 

SiC-SV01 x x x x x x x x x x x x x x x x 

SiC001 x x x x x x x x x x x x x x x x 

SiC001-PG x x x x x x x x x x x x x x x x 

SiCT001-PG x x x x x x x x x x x x x x x x 

SiC003 x x x x x x x x x x x x x x x x 

SiC003-PG x x x x x x x x x x x x x x x x 

SLS-SiC003 x x 

SLS-SiC003-PG x x 

SLS-SiC004 x x 

SLS-SiC004-PG x x 

SiC007-P x x x x x x x x x x x x x x x x 

SiC007-P-PG x x x x x x x x x x x x x x x x 

SiC007-I x x x x x 

SiC007-I-PG x x x x x 

SiC007-U2 x x 

SiC007-U2-PG x x 

SiC007-U3 x x x x 

SiC007-U3-PG x x x x 

SiC007-U10 x 

SiC007-U10-PG x 

SiC021-I x x x x x 

SiC021-I-PG x x x x x 

SiC021-U2 x x 

SiC021-U2-PG x x 

SiC021-U3 x x x x 

SiC021-U3-PG x x x x 

SiC021-U10 x 

SiC021-U10-PG x 

SiCDVGW001-LP x x 

SiCDVGW001-MP x x 

SiCDVGW002-LP x x x x x 

SiCDVGW002-MP x x x x x 

SiCONORM001-LP x x 

SiCONORM001-MP x x 

SiCONORM002-LP x x x x x 

SiCONORM002-MP x x x x x 

Sensors and Monitors for the Digital Operation System 

Digital Sensors Accessories UV-Monitors 

D-SiC003(-PG)(-F) Interface IF03 

PRO11 



for connection of 

analog (uv-diode output)sensors: 

PRO16 

PRO20 

D-SiC007(-PG)(-F) SiC-SV01 PLC 

D-SiC021(-PG)(-F) SiC001(-PG) 

D-SiCDVGW SiCT001-PG 

D-SiCONORM SiC003(-PG) 

SiC007-P(-PG) 

PRO15 

PRO15-SLS 

PRO16P 

PRO16I(-I) 

PRO16U3(-I) 



PRO16PI(-I) 

PRO16PU3(-I) 

PRO20 

UV-Compact 

IF01 

IF02 

IF03

09/2006 

PRO 2 

PRO 3 

Available Monitor Types 

monitor 

type 

Functions: 

• display of the relative uv-output with three 

LED's: 

� GREEN: function o.k. 

� YELLOW: pre-alarm 

� RED: main alarm 

Attention: Risk of electric shock! 

- 31 - 



UV-Monitor PRO 2 with Status Indication by LED 

UV-Monitor PRO 3 with Relay Contacts and Status Indication by LED 

for monitoring of the relative uv-intensity, e.g. in uv disinfection systems 

sensor signal relay contact weight suitable sensor types 

PRO2 diode output no relay contact 120g SiC-SV01, 

PRO3 diode output potential free relay contact, load: 

5mA...1A/5V...230V AC 

5mA...1A/5V...60V DC 

relay threshold 50% 


mains voltage: 230V AC ± 10% /50/60 Hz 

(115V AC/60Hz or 24V DC 

types available on request) 

• PRO 3: potential free relay contact 

in accordance with status indication 

for main alarm 

• multi turn potentiometer for fine 

adjustment of sensitivity at 110%, 

shown through a green LED nearby the 

potentiometer 

operating 

temperature: 

measurement range: adjustable for customer purpose by manufacturer 

status indication: 3 LED: 

green: function o.k. 

yellow: pre-alarm 

red: main alarm 

switching 

thresholds: 

The device must be installed in a closed cabinet, otherwise lethal parts can be touched by hand. 

The device may be installed by authorized personnel only, to make sure all applicable safety rules are fulfilled. 

Please consider the safety instructions in the installation and operating manual. 

0...40°C storage 

temperature 

range: 

red: 0 - 49% (main alarm) 

yellow: 50 - 74% (pre-alarm) 

green: > 74% (function o.k.) 

(or customers specification) 

dimensions (w/h/l): (75/49/41)mm mounting: 4 mounting holes ∅ 3,8mm 

hole center distance: (65 x 38)mm 

150g 

SiCT001-PG, 

SiC001(-PG), 

SiC003(-PG), 

SiC007-P(-PG) 

-40°C...+70°C 

For use in dry environment only! 




monitor 

type 

09/2006 

sensor 

signal 

PRO5-PF diode 

output 

PRO5 diode 

output 

PRO8 diode 

output 

suitable 

sensor 

types 

SiC-SV01, 

SiCT001-PG, 

SiC001, 

SiC001-PG, 

SiC003, 

SiC003-PG, 

SiC007-P, 

SiC007-P-PG 

PRO 5-PF 

PRO 8 

switching 

thresholds 

red: 0...49% 

(main alarm) 

yellow: 

50...74% 

(pre-alarm) 

green: > 74% 

(function o.k.) 

(or customers 

specification) 

Functions 

• display of the relative uv-output with three 

LED's: 

� GREEN: function o.k. 

� YELLOW: pre-alarm 

� RED: main alarm 

- 32 - 

PRO 5 



(115V AC/60Hz or 24V DC types 

available on request) 



UV-Monitor PRO 5/ PRO 8 with Relay Contacts 

and Status Indication by LED 

for monitoring of the relative uv-intensity, e.g. in uv disinfection systems 

relay contact load potentiometer 

for fine adjustment 

50...200mA/24V...230V AC 

100...500mA/24V...60V DC 

50...200mA/24V...230V AC 

100...500mA/24V...60V DC 

50...200mA/24V...230V AC 

50...500mA/24V...60V DC 

• potential free relay contacts in accordance 

with status indication: 

� PRO 5: main alarm 

� PRO 8: pre-alarm, main alarm 

operating 

temperature: 

measurement range: adjustable for customer purpose in wide range 

status indication: LED green: function o.k. 

LED yellow: pre-alarm 

LED red: main alarm 

relay contact 

for alarm: 

Accessories - cover for uv monitors for protection level IP65 at front 

cover for 

UV-Monitor PRO5 

dimensions 

(w/h/l): 

at front side (72/72/77) 

mm 

at back side (72/72/77) 

mm 

at back side (96/48/80) 

mm 

mounting weight 

cut-out 

according 

DIN43700 

(68 +0,7 x 68 +0,7 ) 

cut-out 

according 

DIN43700 

(68 +0,7 x 68 +0,7 ) 

cut-out 

according 

DIN43700 

(92 +0,8 x 45 +0,6 ) 

240g 

240g 

250g 

• multi turn potentiometer for fine adjustment 

of sensitivity at 110%, shown 

through a green LED nearby the potentiometer 

(available at front or back side of the 

monitor) 

0...40°C storage 

temperature 

range: 

potential free relay contact 



-40°C...+70°C 





09/2006 

- 33 - 



UV-Monitor PRO10.4 with Relay Contacts 

and Status Indication by LED and LCD 

for monitoring and evaluation of relative and absolute uv-intensity (depending on sensor type) 

and for displaying the specific irradiation, determined from flow rate measurement and reactor vessel volume 

Accepted by DVGW and OENORM 

monitor type sensor signal suitable sensor types 

PRO10.4 diode output or 

current output 

PRO10.4-U2 diode output or 

voltage output 

Functions: 

• LCD-Display: uv-intensity in % or W/m² 

(in case of calibrated sensor); 3 front LED: 

operating status 

• accepts a wide variety of sensor types: 

photo diodes, current sensors (Austrian 

ÖNORM or German DVGW), voltage 

sensors on request 

• adjustment of end value in %: 

� coarse adjustment of 

sensitivity* in 8 steps, 

� fine adjustment in a small range 

by special multi turn 

potentiometer (if a photodiode is 

used), 

� display of 110% - value at rear 

panel (green LED flashes) 

• adjustment of end value in W/m² 

SiC-SV01, SiC001(-PG), SiCT001-PG, SiC003(-PG), SiC007-P(-PG), SiC007-I(-PG), 

SiC021-I(-PG), SiCDVGW002-LP, SiCDVGW002-MP, SiCONORM002-LP, SiCONORM002-MP 

SiC-SV01, SiC001(-PG), SiCT001-PG, SiC003(-PG), SiC007-P(-PG), SiCDVGW001-LP, 

SiCDVGW001-MP, SiCONORM001-LP, SiCONORM001-MP, SiC007-U2(-PG), SiC021-U2(-PG) 

PRO10.4-SLS diode output side looking sensors: SLS-SiC003(-PG), SLS-SiC004(-PG) 

depending on the sensor type* (using 

a calibrated sensor with standard 

current port: 4-20mA, 0-20 mA; 0-2 

V on request) 

• two potential free relay contacts indicate 

pre alarm and main alarm condition, switching 

thresholds can be programmed* 

• internal real time clock for counting 

purposes* 

• internal hour counter to determine the 

total operation time of the system 

• user programmable hour counter e.g. for 

counting operation hours of the lamps 

• end of lamp life time display*, after 

reaching the programmed value the yellow 

LED is blinking 

• two display modes to display either uvintensity 

value or the user programmable 

hour counter, switched by a switch input at 

the rear side of the device 

• contact for fault of lamp alarm; by shorting 

this contact externally the red LED is blinking 

and the main alarm relay operates 

• input to sense operation mode "UV-off". If 

the unit does not work continuously this 

contact stops counting of operation hours 

and uv measuring, the last counter reading 

remains stored; to prevent alarm during 

starting up or switching on again, a delay 

time can be programmed* 

• internal operating cycle counter* 

• RS232 - port for service at the rear panel 

of the device 

*can be programmed by manufacturer and/ 

or by customer by service device SER10 or 

by PC (software MONITOR_ORGANIZER 

required) 


mains voltage: 230V AC ± 10% /50/60 Hz operating 

0...45°C protection level: IP00 

(115V AC/60Hz or 24V DC temperature: 

(IP65 at front on 

types available on request) 

request) 

measurement range: adjustable for customer purpose in wide range output signal: 4-20mA 

status indication: LCD: 

3 LED (front): 

1 LED (back): 

3 digits, 

green: function o.k. 

adjustment of sensitivity 

9mm heigth 

yellow: pre-alarm 

red: main alarm 

green: >110% 

relay contact for potential free relay contact relay contact load: 50-500mA at 24V-230V AC 

alarm: 

100-500mA at 24V-60V DC 

dimensions (w/h/l): (96/48/134)mm mounting: cut-out according DIN43700 (92 +0,8 x 45 +0,6 ) 

weight: 300g 





for side looking sensors please order uv-monitor PRO10.4 SLS 



Service device SER10 

Functions: 

• automatic change to the service mode, 

after the connection of the service device 

• display and setting of the internal monitor clock 

• display of the total operating hour counter 

• display and reset of the user programmable hour counter 

• set of lamp operation time 

• display and change of the delay time after "UV-off" 

• display and change of the threshold for main alarm 

• display and change of the threshold for pre alarm 

• configuring of sensor input (current input or fotodiode) 

• coarse adjustment of input sensitivity 

(8 steps) if a fotodiode is used 

• adjustment of end value (1...1999W/m²) 

if a current or voltage sensor is used 

• display and reset of the operating cycle counter 

• a 9V block battery is required 

Technical Specification SER10 

power supply: 9V (battery or accumulator) 

operating temperature: 0...45°C 

storage temperature 

range: 

-40°C...+60°C 

weight: 200g 

accessories: interface cable, instructions 

status indication: LCD 3 digits, 9mm heigth 

dimensions (w/h/l): (60/125/25)mm 

protection level: IP00 

09/2006 

- 34 - 



Service Device and Service Software for UV-Monitor PRO10 

for the adjustment of the uv system parameters 

SER10 MONITOR_ORGANIZER 


Software MONITOR_ORGANIZER V2.02eng 

Functions: 

• display of all data from the UV-Monitor PRO10 

• setting and storage of new configurations at the Monitor PRO10 

• adjustment of the alarm value thresholds for operation of the 

potential free relay contacts 

• display and change of the delay time after "UV-off" 

• display of the operating cycle counter 

• setting of lamp operation time 

• special function to turn on and off of a pump contact (by 

request) 

• display of total hour counter 

• display and change of user programmable hour counter 

• selection of a standard current port 

• date/ time adjustment 

• selection of sensor input 

• special function for calculating of specific irradiation based on 

intensity, flow rate and reactor vessel volume on request 

• configuration can be saved at PC harddisk 

• language can be adapted 





09/2006 

- 35 - 



UV-Monitor PRO11 with Relay Contacts 

and Status Indication by backlighted LCD 

for monitoring and evaluation of relative and absolute uv-intensity (depending on sensor type) 

and for displaying the specific irradiation, determined from flow rate measurement and reactor vessel volume 

monitor type sensor signal suitable sensor types 

PRO11PI-I diode output or 


PRO11PU3-I diode output or 


Functions: 

• LCD-Display: 

� synchronous readout of uvvalue 

(1st row of display) and 

operating hours (2nd row of 

display), 

� green (normal), yellow (prealarm) 

and red (main alarm) 

back lighting, 

� uv-intensity 

in %, W/m² or mW/cm² 

(in case of calibrated sensor) 


photo diodes, current sensors, voltage 


• automatic adjustment of end value (using 

a photodiode) 

• adjustment of end value in W/m² depending 

on the sensor type* 




SiC-SV01, SiC001(-PG), SiCT001-PG, SiC003(-PG), SiC007-P(-PG), SiC007-I(-PG), SiC021-I(-PG), 

SiCDVGW002-LP, SiCDVGW002-MP, SiCONORM002-LP, SiCONORM002-MP 

SiC-SV01, SiC001(-PG), SiCT001-PG, SiC003(-PG), SiC007-P(-PG), SiC007-U3(-PG), SiC021-U3(-PG) 

operating 

temperature: 


(IP65 at front on 

request) 

measurement range: automatic adjustment output signal: 4...20mA (potential free) 

status indication: LCD: 2*12 digits, 14,5mm heigth backlight colour: green: function o.k., yellow: pre alarm, red: main alarm 

relay contact for alarm: 2 potential free relay contacts relay contact 50-500mA at 24V-230V AC 

load: 

100-500mA at 24V-60V DC 

dimensions (w/h/l): (96/48/114)mm mounting hole: cut-out according DIN43700 (92 +0,8 x 45 +0,6 ) 

weight: 300g 




(using a calibrated sensor) 

• two potential free relay contacts indicate 


thresholds can be programmed* 


purposes* 





• end of lamp life time display*, after 

reaching the programmed value display 

shows "exchange lamp" 


this contact externally the display shows 

"lamp error" 

• input to sense operation mode "UV-off"; 

if the unit does not work continuously this 

contact stops counting of operation hours 

and uv measuring, the last counter reading 

remains stored; to prevent alarm during 

starting up or switching on again, a delay 

time can be programmed* 

• internal operating cycle counter* 

• RS232 - port for service at the rear panel 

of the device 

• optional RS485 - port for digital operation 

system 


*can be programmed by manufacturer and/ 

or by customer 


for side looking sensors please order uv-monitor PRO11SLS 




monitor type supply suitable sensor types 

PRO15 /230V AC 230V AC ± 10% 50/60Hz 1,8W SiC-SV01, SiC001(-PG), SiCT001-PG, 

PRO15 /115V AC 

PRO15 / 12V DC 

115V AC ± 10% 50/60Hz 1,8W 

12V DC ± 10% 50/60Hz 1,8W 

SiC003(-PG), SiC007-P(-PG) 

on request: 

SLS-SiC003(-PG), 

PRO15 / 24V DC 24V DC ± 10% 50/60Hz 1,8W SLS-SiC004(-PG) 

Monitoring Features 

• synchronous readout 

of uv-value (1st row of display) 

and operating hours (2nd row of display) 

• menu operation by buttons 

09/2006 

- 36 - 

uv-value monitoring: 


• message "UV-value low" in case of uvvalue 

below switching threshold 

• adjustment of sensitivity 

(automatic end adjustment) 


mains voltage: see monitor type CE-conform: yes 


temperature: 

0...40°C 

display: 2*8 digits, adjustment of contrast by potentiometer 



dimensions (w/h/l): (72,5/44/72,5)mm weight: 170g 

relay contact for alarm: potential free relay contact load: 

50-200mA at 24V-120V AC 

50-500mA at 5V- 24V DC 

running time 

of the clock: 



UV-Monitor PRO15 with Relay Contacts, Status Indication by LCD, 

Integrated Hour Counter 

approx. 8 years 

The monitor is intended for monitoring of the relative uv-intensity. 

Monitor Pro15 types for sidelooking 

sensors (SLS) available on request 

hour counter: 


• total operation time 

• programmable lamp hour counter 

• programmable lamp lifetime 

• message "exchange lamp" in case of 

reached end of lamp lifetime 

pin assignment: 

pin 3: normally off contact 

pin 4: change-over contact 

pin 5: normally on contact 






09/2006 

- 37 - 



UV-Monitor PRO16 with Relay Contacts, Status Indication by LCD, 

Integrated Hour Counter 

PRO16P 

The monitor is intended for monitoring of absolute/relative uv-intensity. 

PRO16I 

PRO16U3 

PRO16I-I 

PRO16U3-I 

Features 

• various input types 

• uv intensity 

- absolute measurement 

by using a calibrated sensor 

- relative measurement 

by using a photodiode 

• automatic sensitivity 

adjustment (photodiode) 

• 2*12 digit display 

(red/green backlight) 

• internal clock 

• global and user hour counter 

• adjustable end of lamp 

lifetime alarm 

• adjustable uv-low alarm 

• fault relay - potential free 

relay contact 

• menu lock 

photodiode input x x x x x 

4...20mA current input x x x x 

0...3V voltage input x x x x 

4...20mA current output x x x x 

absolute measurement x x x x x x x x 

relative measurement x x x x x x x x x 

sensor power supply +12V DC stabilised x x x x x x x x 

Dimensions Block schematic 


mains voltage: 230V AC ± 10% 50/60Hz 2W CE-conform: yes 

mains frequency: 45...65Hz ambient temperature: 0...40°C 

display: 2*12 digits, green or red back lighting for status indication, 

adjustment of contrast by menu 


language: alternatively English or German 

dimensions (w/h/l): (72,5/44/72,5)mm weight: 200g 

relay contact: load: 20-200mA at 24V-120V AC / 20-500mA at 5V- 24V DC 

running time of the clock: approx. 8 years 

photodiode input 

(PRO16Px-x) 

4...20mA input 

( PRO16xI-x) 

0...3V input 

( PRO16xU3-x) 

4...20mA output 

(PRO16xx-I) 



PRO16PI 

PRO16PU3 

central 

processing 

unit 

PRO16PI-I 

2*12 display 

buttons 

real time clock 

memory 

relay 

power supply 



PRO16PU3-I


09/2006 

PRO 20 

Functions: 

• LCD-Display: 

� different (customer specific) 

display modes, 

� green, yellow and red back 

lighting, 

� uv-intensity in % or W/m² (in 

case of calibrated sensor) 


photo diodes, current sensors (Austrian 

OENORM or German DVGW), voltage 


• automatic adjustment of end value 

• adjustment of end value in W/m² 

depending on the sensor type* (using a 

calibrated sensor with standard current 

port: 4-20mA; 0-20 mA; 0-2 V on request) 




sensor ports: 4 diode-output-sensors 

(optional: 

current or voltage output) 

2 additional inputs for currentoutput 

sensors or flow meter 

additional ports: 4 optic isolated gate inputs 

3 potential free relay contacts 

(change-over contact) 

1 potential free output 4...20mA 

- 38 - 



UV-Monitor PRO20 for Analog and Digital Multi-Sensoring 

for monitoring and evaluation of relative and absolute uv-intensity 

(depending on sensor type) 

and for displaying the specific irradiation, 

determined from flow rate measurement and reactor vessel volume 

PRO 20-S 

operating 

temperature: 

suitable sensor 

types: 

relay contact load: 50-500mA at 24V-230V AC 

100-500mA at 24V-60V DC 

measurement range: adjustable for customer purpose in wide range 

status indication: LCD 4*20 digits 

with green, yellow and red 

back lighting 

for status indication 

dimensions (w/h/l): with housing (PRO 20): 

(143/143/67)mm 

• input for temperature sensor 

• three potential free relay contacts indicate 


thresholds can be programmed 

• four optic isolated gate inputs for switching 

purposes 

• internal buzzer (disengageable) for status 

indication 


purposes 





1 RS485 interface for digital sensor bus 

(digital operation system) 

1 measurement input for temperature 

1 RS232-port for service 

internal buzzer 

(disengageable) 

without housing (PRO 20-S): 

(134/134/45)mm 

• end of lamp life time display, after reaching 

the programmed value display shows 

"exchange lamp" 


this contact externally the display shows 

"error lamp" 

• calculation of the specific irradiation by 

Ee and flow 


• extensive customer specific menu system 

editable (different languages) 


(IP65 at front 

on request) 

P-SiC003, P-SiC003-PG, P-SiC007, P-SiC021, 

P-SLS-SiC003, P-SLS-SiC004 

P-SiCDVGW, P-ONORM 

with Interface IF03: 

SiC-SV01, SiC001, SiC001-PG, SiCT001-PG 

weight: 300g mounting: cut-out according DIN43700 (138 +1,0 x 138 +1,0 ) 




09/2006 

- 39 - 

Silicon Carbide UV Diode SiC-0,1/SiC-0,1-F/SiC-0,25 

for ZED UV sensors 

UV-Sensor SiC-SV01 

with diode output 

UV-Sensor SiC001/SiC001-PG 


UV-Sensor SiC001T-PG 

teflon sensor with diode output 

UV-Sensor SiC003/SiC003-PG 


UV-Sensor SLS-SiC003/SLS-SiC003-PG 

side-looking sensor with amplified diode output 

UV-Sensor SLS-SiC004/SLS-SiC004-PG 

side-looking sensor with amplified diode output 

UV-Sensor SiC007-x / SiC007-x-PG 

with diode, current or voltage output 

UV-Sensor SiC021-x / SiC021-x-PG 

with current or voltage output 

UV-Sensor SiCDVGWx/SiCONORMx 

according to German rule W294 / Austrian rule OENORM 

with voltage or current output 



UV-Sensors - Overview 

for measurement in uv-units 




diode name spectral 

range [nm] 

09/2006 

SiC-0,1 

SiC-0,1-F 

(with uvc-filter) 

SiC-0,25 

uv sensitive 

area [mm²] 

- 40 - 


Silicon Carbide UV Diodes 

for ZED UV Sensors 

exclusively for uv measurement, e.g. monitoring of sterilistaion lamps or flame monitoring 

body: TO 18 (SiC-0,1, SiC-0,25: diode is electrically isolated from housing) 

operation temperature: -25°C...70°C storage temperature: 0°C...100°C 

soldering temperature: 260°C (3s max.) 

max. uv 

sensitivity 

on λ max = 

275nm 

max. uv 

sensitivity 

on λ max = 

254nm 

dark current 

[fA] 

on V R =1V 

short-circuit 

current [nA] 

on bright 

sun/cloudy 

sky 

reverse 

voltage [V] 

SiC-0,1 210...380 0,0625 0,13 A/W 0,11 A/W 1 50/20 20 21 

SiC-0,1-F 210...280 0,0625 1 - 20 21 

SiC-0,25 210...380 0,25 1 50/20 20 21 

capacity 

[pF] 

Shielding connection must not be used as earth connection for safety reasons. 



SiC001 

Available Sensor Types 

09/2006 

SiC-SV01 SiC003 

- 41 - 

PG versions without plug connection between sensor and cable. 



UV-Sensors for Monitoring of Relative UV-Intensities 

to be used for measurement in UV-units 

SiC003-PG SiCT001-PG 

SiC001-for UV-Compact SiC001-PG SiC001-PG-BNC 

type thread/length wrench diameter length [mm] weight [g] suitable monitor types 

for mounting size [mm] [mm] 

SiC-SV01 - - 17,5 38,5 140 (including 1m cable) 

SiC001 

SiC001-PG 

G 1/4’’ / 14mm 

G 1/4’’ / 14mm 

19 

19 

21,7 

21,7 

49 (with plug: 84) 55 (+115g cable and plug) 

61 125 (including 1m cable) 

PRO2, PRO3, PRO5, 

PRO8, PRO10.4, PRO11 

PRO15, PRO16, 

SiCT001-PG G 1/4’’ / 14mm 17 20 57 85 (including 1m cable) IF01, IF02, IF03 

SiC003 G 3/4’’ / 11mm 32 37 52 (with plug: 87) 195 (+115g cable and plug) 

SiC003-PG G 3/4’’ / 11mm 32 37 63 270 (including 1m cable) 

SiC001 for UV- 

Compact1 

G 1/4’’ / 14mm 19 21,7 49 55 (no additional cable) UV Compact MC 

SiC001-PG-BNC G 1/4’’ / 14mm 19 21,7 61 180 (including 2m cable) UV Compact MCplus 


diode type: silicon carbide (SiC) 0,0625mm² 

(SiCT001-PG: 0,25mm²) 

spectral range: 210...380nm 

(with uvc-filter: 210...280nm) 

max. pressure: SiC001(-PG)/SiCT001-PG/SiC003(-PG):10bar 

SiC-SV01: diode is sealed with quartz window-protection 

against humidity only 

body: stainless steel 1.4305 

(SiCT001-PG: Teflon) 

flare angle: 26° 


connection: 2wire cable, shielded: 

SiC001/SiC003: mounting cable with straight connector M12, length 2.90m 

(IP65 if inserted and screwed with straight M12 connector) 

SiC-SV01, SiC001-PG, SiCT001-PG, SiC003-PG: mounted cable, length 1m (up to 2,90m on request) 

SiC001 for UV-Compact: no additional cable (cable with straight connector M12 already mounted on UV Compact MC) 

SiC001-PG-BNC: mounted cable with BNC-Plug for connection to UV Compact MCplus 

mounting 

restrictions: 

cover thread with teflon tape or ceramo paste before mounting 

Sensor SiC003(-PG) is also available as digital sensor for digital operation system, 

please order D-SiC003(-PG). 

SiC-SV01, SiC001(-PG), SiC003(-PG), SiCT001-PG require interface IF03 for 

interconnection with digital operation system. 

The sensors are daylight blind (see diagramm) and standard without uvc-filter. 

Limitation of spectral sensitivity with uvc-filter is available on request for use with 

medium pressure lamps. Add “-F“ for sensor with uvc filter. 




type thread/length 

for mounting 

Add “-F“ for sensor with uvc filter. 

Side-Looking sensors are also available as digital sensors for digital operation system. 

Please order D-SLS-SiC003(-PG)/D-SLS-SiC004(-PG). 

09/2006 

extended flare angle 

of side looking sensors 


- 42 - 

wrench 

size [mm] 

diameter 

[mm] 

SLS-SiC003 SLS-SiC003-PG 

SLS-SiC004 SLS-SiC004-PG 



UV-Sensors with Extended Flare Angle (Side-Looking Sensors) 

for Monitoring of Relative UV-Intensities 

length [mm] weight [g] suitable monitor types 

SLS-SiC003 G 3/4“ / 11mm 32 37 70 (with plug: 120) 190 (+115g cable and plug) 

SLS-SiC003-PG G 3/4“ / 11mm 32 37 81 270 (including cable) 

SLS-SiC004 - - 21,5 75 (with plug: 127) 85 (+115g cable and plug) 

SLS-SiC004-PG - - 21,5 86 171 (including cable) 


diode type: silicon carbide (SiC) 0,25mm² body: stainless steel 1.4305 



flare angle: see diagram above 

max. pressure: 10bar operating temperature: 0...40°C 

to be used for measurement in UV-units 

• daylight blind 

(see diagramm below) 

• standard without uvc-filter 

• limitation of spectral sensitivity 

with uvc-filter on 

request 

• PG versions without 

plug connection between 

sensor and cable 

• integrated amplifier ±5V 

(DC supply necessary) 

PRO10.4 SLS, 

PRO15 SLS 

connection: SLS-SiC003 / SLS-SiC004: connector M12, mounting cable with plug included, length: 2.90m 

SLS-SiC003-PG / SLS-SiC004-PG: cable length 1m (up to 2,90m on request) 

supply voltage: ±5V 

mounting restrictions: cover thread with teflon tape or ceramo paste before mounting 

Limitation of spectral sensitivity with uvc-filter available 

on request for use with medium pressure lamps. 





09/2006 

SiC007-P-PG 

• adjusted versions with current or voltage output 

• photodiode output versions also available 

• PG versions without plug connection 

between sensor and cable 


- 43 - 

SiC007-I-PG 

SiC007-Ux-PG 

SiC007-P 



UV-Sensor SiC007 for MF001 with various output signals 

for the measuring / monitoring of UV irradiation 

SiC007-I 

SiC007-Ux 

• suitable as plug-in sensor in measurement window MF001 

• daylight blind (see diagramm below) 


• limitation of spectral sensitivity with uvc-filter on request 

sensor type signal output value adjusted value* min. load 

resistance R min 

* other values on request. Add “-F“ for sensor with uvc filter. 

SiC007(-PG) is also available as digital sensor for digital operation system. Please order D-SiC007(-PG). 

max. load 

resistance R max 

SiC007-P photodiode output diode current - - - 

SiC007-P-PG photodiode output diode current - - - 

SiC007-I current output 4 - 20mA 20mA - 9V⇒330Ω / 24V⇒1kΩ 

SiC007-I-PG current output 4 - 20mA 20mA - 9V⇒330Ω / 24V⇒1kΩ 

SiC007-U2 voltage output 0 - 2V 2V 220Ω - 

SiC007-U2-PG voltage output 0 - 2V 2V 220Ω - 









supply voltage UB : 

9… 24V stabilised, I ≤ 25mA linearity within the initial 2% 

(current/voltage output) (min. 12V for SiC007-U10) voltage range: 

temperature drift: 0,03 W/m²/K max. pressure: diode is sealed with quartz windowprotection 

against humidity only 


dimensions: body-diameter: 20mm 

length: 

weight: 

outer ring: 27mm 

86mm (SiC007) 

120g (SiC007) 

95mm (SiC007-PG, without cable) 155g (SiC007-PG with 1m cable) 

connection: SiC007: connector M12 (Hirschmann cable plug ELST 5012), 

mounting cable with plug included, length: 2.90m 

SiC007-PG: cable length 1m 

(other cable lengths on request) 



Mounting Restrictions 

Attention! The sensor is not suitable for directly use in water! The diode is 

sealed with quartz window-protection against humidity only. Please do not 

touch the surface of the sensor window. 

We recommend the use of a sealing ring (O-ring, 20x1,5) in the outer ring. 


Do not connect or disconnect sensor-plug while supply voltage is switched on. 



09/2006 

SiC021-x-PG 



- 44 - 

SiC021-x 



UV-Sensor SiC021 with various output signals 

sensor type signal output value adjusted value* min. load 

resistance R min 

for the measuring / monitoring of UV irradiation 

* other values on request 

Add “-F“ for sensor with uvc filter. 

SiC021-PG is also available as digital sensor for digital operation system. Please order D-SiC021(-PG). 

• adjusted versions with 

current or voltage output 

• daylight blind 

(see diagramm below) 


• limitation of spectral sensitivity 

with uvc-filter on request 

• PG versions without plug 

connection between sensor 

and cable 

max. load 

resistance R max 

SiC021-I current output 4 - 20mA 20mA - 9V⇒330Ω / 24V⇒1kΩ 

SiC021-I-PG current output 4 - 20mA 20mA - 9V⇒330Ω / 24V⇒1kΩ 











supply voltage UB : 9… 24V stabilised, I ≤ 25mA linearity within the initial 2% 

(min. 12V for SiC021-U10) voltage range: 

temperature drift: 0,03 W/m²/K max. pressure: 10bar 


dimensions: thread: G1/4’’ 

length: 

weight: 

wrench size:19 

67mm (SiC021) 

77g (SiC021) 

body-diameter: 22mm 

78mm (SiC021-PG without cable) 105g (SiC021-PG with 1m cable) 

connection: SiC021: connector M12 (Hirschmann cable plug ELST 5012), 

mounting cable with plug included, length: 2.90m 

SiC021-PG: cable length 1m 

(other cable lengths on request) 

mounting restrictions: cover thread with teflon tape or ceramo paste before mounting 




Do not connect or disconnect sensor-plug while supply voltage is switched on. 



SiCDVGW SiCONORM 


* output value 0...10V on request 

09/2006 

- 45 - 

• suitable as plug-in sensor 

in measurement window 

MF001 

• several supply voltages 

available 

• several output signals 

available 



UV-Sensors adapted to Special Regulations, Calibrated 

according to German rule W294, resp. Austrian rule OENORM 

sensor type signal output value* suitable monitor types lamp types 

SiCDVGW001-LP voltage output 0...2V 

low pressure lamps 

SiCDVGW001-MP 

SiCONORM001-LP 



0...2V 

0...2V 

PRO10.4 (0-2V) 

medium pressure lamps 


SiCONORM001-MP voltage output 0...2V medium pressure lamps 

SiCDVGW002-LP current output 4...20mA PRO10.4, 


SiCDVGW002-MP 

SiCONORM002-LP 



4...20mA 

4...20mA 

PRO11PI-I, 

PRO16I (-I) 

PRO16PI (-I) 

medium pressure lamps 


SiCONORM002-MP current output 4...20mA medium pressure lamps 


uv-sensor: silicon carbide-(SiC) diode 

0,25*0,25mm² 

dimensions: diameter of the body: 20mm 

diameter of the outer ring: 27mm 

length: 91mm 

insert length: 59mm 

body: stainless steel 1.4307 

weight: 83g (without cable) 

supply voltage UB: 9… 15V stabilised linearity within the 

initial voltage range: 

2% 

operation current: SiCxxx001:

Spectral Sensitivity for Low and Medium Pressure Lamps 

relative sensitivity [%] 

120 

100 

80 

60 

40 

20 

0 

190 

Measurement window MF001 for DVGW-sensors and ONORM-sensors 

The uv-measurement window according to rule W294, 

suitable for input of DVGW Sensor SICDVGW***, 

the uv-measurement window according to rule OENORM, 

suitable for input of ONORM Sensor SICONORM***, 

watertight up to 10bar, 

consists of: 

• stainless steel (1.4305) body: 

length: 65mm / wrench size: 32 / thread: G1’’, 20mm long 

weight: 365g 

• hole for sensor input 

∅20 x 60mm with cap nut M30 x 2 to connect the sensor 

• window made from quartz glass 

∅24,5 x 5mm 

09/2006 

low pressure lamps: spectral sensitivity 

Characteristics 

240 

290 

wavelength [nm] 

340 

390 

- 46 - 



UV-Sensors adapted to Special Regulations, Calibrated 

relative sensitivity [%] 

according to German rule W294, resp. Austrian rule OENORM 

120 

100 

80 

60 

40 

20 

0 

200 

medium pressure lamps: spectral sensitivity 

actual value of the sensor 

desired value according to DVGW 

220 240 260 280 300 320 340 

wavelength [nm] 

MF001 



Functions: 

1. amplification of the signal output of fotodiode current sensors to voltage 

output 0...5V (IF01) resp. current output 4...20mA (IF02) 

2. adjustment of the sensor output signal according to the requirements 

of the PLC (IF01, IF02) or of the digital operation system (IF03) 

3. 2 input/output channels 

4. fine adjustment of amplification by multi turn potentiometer 

Available Interface Types 

type output 

IF01 2x 0...5V 

(2x 0...2V on request) 

IF02 2x 4...20mA 

IF03 digital sensor signal 


mains voltage: 230V AC ± 10%, 50Hz 

max. 2,5W 

115V-types available on request 

input: up to 2 fotodiodes 

(adjustment necessary) 

09/2006 

- 47 - 

protection level: IP00 

weight: 200g 

dimensions (w/h/l): (97/48/43)mm mounting: DIN rail 

Examples for wiring 



Interfaces IF01, IF02, IF03 

for the Connection of Sensors and PLC 




SW 5 

Available Lamp Control Types 

type switching 

threshold 

09/2006 

- 48 - 

operation 

current range 

switch on 

delay time 

SW 10 

switch off 

delay time 

SW 5.60 60 mA 60 - 200 mA ca. 0,5s ca. 0,5s 

SW 5.200 200 mA 200 - 800 mA ca. 0,5s ca. 0,5s 

SW 5.800 800 mA 800 - 1000 mA ca. 0,5s ca. 0,5s 

SW 10.60 60 mA 60 - 200 mA ca. 6s ca. 2s 

SW 10.200 200 mA 200 - 800 mA ca. 6s ca. 2s 

SW 10.800 800 mA 800 - 1500 mA ca. 6s ca. 2s 

SW 10.1500 1500 mA 1500 - 2500 mA ca. 6s ca. 2s 

SW 10.2500 2500 mA 2500 - 4000 mA ca. 6s ca. 2s 


mains voltage: 230V AC ± 10% 

mains frequency: 45...65Hz 

using with 



Control Units SW5 and SW10 for Lamp Function Control 

status indication: SW5: 

two potential free relay contacts (closed at correct operation), 

load: 50 - 500mA at 24V - 230V AC; 100 - 500mA at 24V - 60V DC 

SW10: 

green and red LED indicate operating status, 

two potential free change over contacts, 

load: 50 - 500mA at 24V - 230V AC; 100 - 500mA at 24V - 60V DC 

weight: SW5: 70g 

SW10: 200g 


mounting: DIN rail (DIN EN 50 022-35) 

electronic ballasts, monitoring fan, 

other control functions 

dimensions: (w/h/l) SW5: (97/27/43)mm 

SW10: (97/48/43)mm 

starter and choke, 

other conventional circuit, 

electronic ballasts, other control functions 

Control units for other applications are also available. 



09/2006 

- 49 - 



UV-Radiation Meter UVM-CP 

for measurement of radiation intensity 

The UV radiation meter is available for UV-A, UV-B, UV-C and UV/vis. 

The gauge is equipped as standard with a cos-correction, which permits 

exact measurement at short distance. 

The housing of the hand unit is made of polystyrene, the housing of the 

probe of aluminium. 


power supply: 9V (battery or accumulator) operating temperature: 15...40°C 

status indication: LCD 3 digits, 9mm heigth protection level: IP00 

measurement range: 2/20/200/2.000 mW/cm² measurement resolution: 1/10/100/1.000 µW/cm² 

spectral range: UV-A: 310...420nm 

UV-B: 250...370nm 

UV-C: 200...300nm 

UV/vis: 370...440nm 

reproduction: 3/30/300/3.000 µW/cm² 





09/2006 

- 50 - 


UV-Lamps and Accessories 

Quartz Tubes 

Immersion Tube Lamps 

Our product range includes low pressure lamps and 

amalgam lamps of leading manufacturers. 

Beside standard and special uv lamps we offer accessories 

like quartz tubes in different lengths and diameters and 

also special lamp sockets. 

Furthermore we offer the production of uv immersion 

lamps for water disinfection and other applications. 

quartz tubes 

uv immersion tube lamps 



09/2006 

- 51 - 

Lamp Socket: 4pin plastic type 

article code F4P 

dimensions (l/w/h) (16/13/26,4)mm 

wire gauge 0,5...0,8mm² 

max. ambient temperature 60°C 

max. current 1A 

max. voltage 600V 


UV-Lamps and Accessories 

Lamp Sockets for Low Pressure Lamps 

Ceramic Lamp Sockets especially for Amalgam Lamps 

The socket is allowed up to 100W/1A.Wire must be solid or top coated stranded 

copper wire. Solder dipped is not recommended. Strip length: 1,1...1,25cm. 

Wire leads to be fully inserted into wiring port, ensuring uninsulated end of wire is 

not exposed. Use wire end ferrules with a length of 12mm. 

We recommend crimping pliers with square crimping e.g. KNIPEX KN975304. 

Lamp Socket: 2pin plastic type 

article code F2P 

dimensions (diam./h) (18/13)mm 


max. current 1,5A 


Connection by supplied mounting cable. 

Lamp Socket: 4pin ceramic type 

article code KF4P 

dimensions (l/w/h) (17,5/14/23,3)mm 

wire gauge 0,5...2mm² 




Wire must be crimped with included crimp contact, strip length: 3,5mm. We recommend 

AMP PRO-CRIMPER II Hand Tool Assembly 90871-1 with Die Assembly 

90871-2 for crimping contacts. 

Lamp Socket: 2G11 ceramic type 

article code KF2G11 

dimensions (l/w/h) (43/33/23)mm (without spring) 





Wire must be crimped with included crimp contact, strip length: 3,5mm. We recommend 

AMP PRO-CRIMPER II Hand Tool Assembly 90871-1 with Die Assembly 

90871-2 for crimping contacts. 

Crimp Contacts for Lamp Sockets 

article code single pins for KF4P or KF2G11 

dimensions inner diameter: 2,26mm, length: 19,8mm 





strip length: 3,5mm 

We recommend AMP PRO-CRIMPER II Hand Tool Assembly 90871-1 with Die 

Assembly 90871-2 for crimping contacts. 

Do not use the sockets in chemical aggressive and/or humid environment!

Solutions for UV Systems 2 Electronic Ballasts for Low Pressure ...

Create successful ePaper yourself

Delete template?

Save as template?