ALPOCRYL Klarlack (Clear Lacquer) - A. Wenger AG
ALPOCRYL Klarlack (Clear Lacquer) - A. Wenger AG
ALPOCRYL Klarlack (Clear Lacquer) - A. Wenger AG
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Technical Data SheetEffective: 11-11-2011Replaces edition dated: 09-10-2006Data Sheet No. 5453<strong>ALPOCRYL</strong> <strong>Klarlack</strong>(<strong>Clear</strong> <strong>Lacquer</strong>)DescriptionProduct descriptionFast-drying base and top coat for high-quality lacquering.Meets the requirements of DIN 68861 1 B and DIN 4102-1 B1, is perspirationandsaliva-fast according to DIN 53160, formaldehyde-free as well as PVC- andhand-cream-resistant.Raw material baseArea of applicationPolyurethane / acrylic resin combinationFurniture and interiors, kitchen cabinetry, shelving, chairs, benches and tables.Form of supply Colours <strong>Clear</strong>Gloss level1205 super dull matt, 1210 dull matt, 1215 matt, 1220 satin matt,1230 satin gloss, 1250 semi-gloss, 1280 high glossHardener Unipur Hardener 279/H901Packing <strong>Lacquer</strong> Plastic 1 5 10 25 lHardenerSheet metal 0.5 1 2.5 5 lTechnical Data <strong>Lacquer</strong> Hardener MixtureThe data apply for: Alpocryl <strong>Clear</strong> <strong>Lacquer</strong> 1215.They may vary for other colours.Specific gravity (23º C) 0.96 g/cm³ 0.99 g/cm³ 0.96 g/cm³Solids content 30 ± 2 % byweightOrganic solvent content 70 ± 2 % byweight45 ± 2 % byweight55 ± 2 % byweightVOC content (EU) 672 g/l 535 g/l 660 g/lca.ca.31 % byweight69 % byweightShelf life 20°C 12 months 6 months in tightly sealed original containers.Theoretical coverage 150 g/m² 6.5 m²/kg for 40 µm dry coat thicknessSafety DataFEYCO <strong>AG</strong>, Hauptsitz, Industriestrasse 11, CH-9430 St. MargrethenFon +41 71 747 84 11 Fax +41 71 747 85 10 www.feyco-coatings.comPage 1 of 3
Technical Data Sheet No. 5453 Page 2 of 3Observe our Safety Data Sheets No. 545300 and H90100 as well asthe instructions on the label.PreparationSubstrate Product DatasheetStain if necessaryStainCoat thicknessCoverageamountWood substrate 1200 Alpocryl <strong>Clear</strong> <strong>Lacquer</strong> 5453 1 x 150 g/m 2Intermediate sanding with 220 – 280grain1200 Alpocryl <strong>Clear</strong> <strong>Lacquer</strong> 5453 1 x 150 g/m 2Coloured MDF 1200 Alpocryl <strong>Clear</strong> <strong>Lacquer</strong> 5453 1 x 150 g/m 2Surface preparationIntermediate sanding with 220 – 280grain1200 Alpocryl <strong>Clear</strong> <strong>Lacquer</strong> 5453 1 x 150 g/m 2Intermediate sanding with 220 – 280grain1200 Alpocryl <strong>Clear</strong> <strong>Lacquer</strong> 5453 1 x 150 g/m 2Please contact our technical staff for further application suggestions.SubstrateEvery substrate must be clean, dry and free of grease and oil.Apply the paint to freshly sanded surfaces only.Wood substrate, bareSand with 150 - 180 grainColoured MDFSand with 150 - 180 grainApplicationPersonal protectionEven if not required by law, wearing personal protective equipment isrecommended.CH: The precautions prescribed by SUVA with respect to hygiene andequipment must be observed.StirringStir paint and hardener thoroughly before use.Mixing ratio 10 : 1 (lacquer : hardener) 279/H901Pot lifeDilution72 hV130 thinner (normal), V095 thinner (slow)FEYCO <strong>AG</strong>, CH-9430 St.Margrethen
Technical Data Sheet No. 5453 Page 3 of 3Brush paintingNoRollingNoTrowelNoViscosity Dilution Nozzle Pressure Spray coatsGravity feed gun 16-18” DIN4 20% 1.4-1.8 mm 3-4 bar 2Suction gun 16-18” DIN4 20% 1.4-1.8 mm 3-4 bar 2UB paint gunNoAirless (airmix) spraying 18-22” DIN4 10% 0.6-0.9 3-4 bar 2HVLP paint gun 16-18” DIN4 20% 1.4-1.8 mm 3-4 bar 2EvaporationPrior to drying at temperatures over 40°C an evaporation time of 15 minutesmust be observed.Drying timeFor 40 µm dry film, at 23°C and 65% rel. humidityDust-dry after: 10 minutesTouch-dry after: 20 minutesRecoatable after: 2 hoursCompletely dry after: 10 daysImportant informationSpecial restrictionsMinimum application anddrying temperatureCoat removalEquipment cleanupPainted surfaces can be coated with Alpocryl <strong>Clear</strong> <strong>Lacquer</strong> to protect thepaint or to adjust the gloss level.+15 °C Not below the dew point.With paint stripperWith a thinner or cleaning agent immediately after use.This data sheet is for your reference and information only. The above data are correct to the best of our knowledge. We offer no guaranteesfor use and exclude any liability. This applies in particular to consequential damage. We are not liable for any advice given by our employees.Our employees give non-binding information only. Site supervision, compliance with handling regulations, and adherence to recognizedengineering rules are the responsibility of the manufacturer, even if our employee was on site during handling. Modifications due to technicaldevelopments may be made. The latest version of this information is applicable. In special cases, please request separate technicalspecifications.FEYCO <strong>AG</strong>, CH-9430 St.Margrethen
Change language