S-A1 100% RTV ACETOXY SILICONE SEALANT - Axtrada

TECHNICAL DAT A SHEETS-A1 100% RTV ACETOXY SILICONE SEALANTDESCRIPTION:S-A1 SILICONE SEALANT IS ONE PART SEALANT THAT OFFER EXCELLENTADHESION, WEATHERABILITY AND ELASTICITY FOR GENERAL GLAZING AND FOR SEALINGAPPLICATION.FEATURES:♦ ACETIC ACID CURING SYSTEM♦ OUTSTANDING DURABILITY♦ ONE PART NO MIXING♦ PERMANENTLY FLEXIBLE♦ EXCELLENT GUNNABILITY (-20°C TO 50°C)♦ WEATHER PROOF♦ LOW SHRINKAGE♦ NO SAGGING♦ PRIMERLESS ADHESION TO MOST MATERIALS♦ UV RESISTANCEUSES:GENERAL GLAZING: GLASS, PLASTIC, CHANNEL OR STOP.CURTAINWALL SEALING: GLASS, METAL, GRANITE AND PLASTIC.GENERAL SEALING: SHEET METAL, SKYLIGHTS, VENTILATORS, AIR-CONDITIONING.GLASS SEALING AND ADHESION FOR AQUARIUM.LIMITATIONS:S-A1 IS AN ACETIC ACID CURING SILICONE AND IS NOT SUITABLE WHERE THE ACETIC ACIDCOMPONENT WILL CORRODE THE BASE MATERIAL.NOT FOR: TRAFFIC AREAS OR AREAS SUBJECT TO ABRASION.NOT FOR: STRUCTURAL GLAZING.NOT FOR: ON MARBLE, QUARTZITE OR NATURAL STONES.JOINT DESIGN:THE SPECIFIED SEALANT BEAD SIZE SHOULD BE CALCULATED TO COMPLY WITH THECOMPRESSION AND EXTENSION CAPABILITIES OF THE SEALANT IN RELATION TO THEANTICIPATED JOINT WIDTH DUE TO EXPANSION AND CONTRACTION.GENERALLY CALCULATION OF THE WIDTH OF S-A1 SEALANT BEAD SHOULD BECOMPUTED ON THE BASIS OF A MAXIMUM ± 25 % COMPRESSION AND EXTENSIONCAPABILITY MINIMUM BEAD SIZE SHOULD NOT BE LESS THAN 3mm TO ACCOMMODATEMOVEMENT.DESIGN JOINT DEPTH OF WHICH RATIO WIDTH BECOMES 0.5 TO 1.SUITABLE JOINT DEPTH VS WIDTH:6mm x 6mm8mm x 12mm10mm x 20mmPage | 1

TECHNICAL DAT A SHEETS-A1 100% RTV ACETOXY SILICONE SEALANTJOINT SIZE MINIMUM 3mm x 3mm.JOINT SIZE MAXIMUN 30mm.APPLICATION:♦ SURFACE MUST BE CLEAN AND DRY.♦ MASK SMOOTH SURFACE TO SIMPLIFY CLEAN UP.♦ USE APPROVED BACK-UP MATERIAL IN JOINT.♦ CUT NOZZLE TO DESIRED SIZE.♦ INSERT CARTRIDGE INTO CAULKING GUN.♦ PUSH SEALANT AHEAD FOR UNIFORM BEAD.♦ TOOL WITHIN 5 MINUTES.♦ CLEAN OFF EXCESS SEALANT WITH M.E.K. OR TOLUENE.CURING TIME:S-A1 SILICONE WILL TACK FREE IN APPROXIMATELY 15 MINUTES AND WILL CURE TO ADEPTH OF 10mm IN 7 DAYS.SPECIFICATION:CURING SYSTEMACETOXYAPPEARANCENON-SAGGING PASTEODOURVINEGAR SMELLSPECIFIC GRAVITY 1.03±0.01SHORE A HARDNESS 23 APPROX.ELONGATION 400%TENSILE STRENGTH 2.0±0.2MPaTACK FREE TIME15 MINUTESAPPLICATION TEMP. -20°C TO 50°CSERVICE TEMP. -50°C TO 150°CSHELF LIFE12 MONTHSCAUTION:UNCURED SEALANT MAY CAUSE SKIN, EYE AND RESPIRATORY SYSTEM IRRITATION.USE ONLY IN WELL VENTILATED AREAS.USE APPROPRIATE PERSONAL PROTECTION TO AVOID CONTACT WITH SKIN AND EYES.IN CASE OF EYE CONTACT OR IRRITATION, FLUSH EYE IMMEDIATELY WITH RUNNINGWATER FOR 15 MINUTES AND GET MEDICAL ATTENTION.IN CASE OF SKIN CONTACT, WASH AFFECTED AREAS WITH HAND CLEANER FOLLOWED BYSOAP AND WATER.PRODUCT RELEASES ACETIC ACID DURING APPLICATION ANDCURING.FOR FURTHER HEALTH AND SAFETY INFORMATION CONSULT THE CURRENTMATERIAL SAFETY DATA SHEET.Page | 2