Collapsible Core - DME

More documents

Recommendations

Info

Info CCM-CCGeneral description of the Collapsible CoresIt is over 30 years since D-M-E first introduced the CollapsibleCore and today it still continues to be a major influence formolding plastic parts requiring internal threads, undercuts,cut-outs etc. During this time a lot of technical knowledgeand experience has been gained from many applicationstackled, some of which have been very complicated. This“Know how” has been constantly passed on to the user, eitherthrough new developments, application improvementsor suggestions for new applications. One such developmentis the new range smaller diameters which complete the seriesof Collapsible Cores. The Collapsible Cores now rangefrom 18 mm to 107 mm, for the outer diameters with thecorresponding inner diameter ranging from 16 mm to 85mm. The effective collapse ranges from 1.1 mm to 4,2 mmper side at the tip of the Core, depending on the diameterof the Core.OperationAfter cooling, the mold opens and the ejector plate assemblymoves forward as far as the stop. This causes the core sleeveto move away from the centre pin and the positive collapsedsleeve to engage, which ensures that all segments have collapsed.However, the molded part remains or hangs until thestripper plate is moved forward to eject the components.This is usually carried out by the activation of two doubleacting air cylinders mounted on the ejector plates and connectedto the stripper plate on the outside of the mold. Thestripper plate is then retracted using the two air cylindersbefore the mold is closed. When closing the mold, one has toensure that the ejector plates are returned before the mold isfully closed. This can be achieved by the use of early ejectorreturns. The core sleeve is returned to the molding positionthus preventing damage to the Collapsible Cores. When themold is fully closed the next cycle can begin. When using CollapsibleCores the designer has a product which offers manyopportunities for producing many variations of molded caps.The result is a mold which functions reliably and economicallyirrespective of whether it concerns a single or multiplecavity mold. Parts with internal protrusions, dimples, interruptedthreads and cut-outs can be economically producedon a high or low volume basis. It should be noted that dueto the design of the Mini Collapsible Core only interruptedthreads and undercuts can be produced. The interruptionsconsist of three small slots with width “J” (See table), but inmost cases this does not imply any technical disadvantages.Design ProcedureThe following steps are used to determine if a part can bemolded on the Mini or Standard Collapsible Core:a) Calculate the expected actual shrinkage “S” = part Ø xshrinkage (%) “S1” = part length x shrinkage (%)b) Determine that the part minor diameter “A” is not less than“A min” (See table and Fig 1)c) Determine that the part major diameter “B” is not greaterthan “B max” (See table and Fig 1)d) Determine that thread depth or part undercut at “L”does not exceed the calculated dimension “C” (seeTable and Fig.1). The collapse available decreasesfrom the front of the core at a rate of 0,02 mm/mm.When the amount of collapse “C” of the Mini or StandardCollapsible Cores is insufficient, Collapsible Cores of thesame size but with a greater collapse can be obtained.TypeCCM-0001CCM-0002CCM-0003CC 125 PCCC 150 PCCC 175 PCCC 250 PCCK Max.1.45 mm/side1.60 mm/side1.80 mm/side0.80 mm/side1.07 mm/side1.20 mm/side1.20 mm/sidee) Determine that part depth “D” (Fig 1) doesnot exceed the value “D” given in the table.Dimension “K min” of the table must be equal to or largerthan “K min”.Material and hardnessTypeCC 252 PCCC 352 PCCC 402 PCCC 502 PCCC 602 PCCC 652 PCCC 702 PCa) The centre pin is manufactured from high quality alloysteel 1.2436, hardened to 60-65 HRC. Centre pins forStandard as well as for Mini Collapsible Cores are fittedto a specific core and cannot be interchanged. This is dueto the centre pin and core sleeve being assembled andground together.b) Core sleeves are manufactured in a 1.2363 steel (AISI01) and hardened to 55-60 HRC. All centre pins and coresleeves carry a serial number. Always verify the serialnumber prior to grinding or final assembly.c) The positive collapse sleeve is manufactured in tool steeland hardened to 55 ± 5 HRC. It is designed to functionwhen the Collapsible Core fails to collapse independentlyupon withdrawal of the centre pin. Its aim is an additionaland necessary safety factor.What materials can be molded?CK Max.1.60 mm/side2.10 mm/side2.65 mm/side3.20 mm/side3.75 mm/side4.06 mm/side4.32 mm/sideCK = Collapse per side at top of core.All commonly used thermoplastic molding resins. For manyyears filled and non-filled molding resins have been successfullymolded. Special requirements have to be taken intoconsideration when PVC is processed. When using the Minior Standard Collapsible Cores for processing this material itis recommended you contact D-M-E.www.dme.net
CCMCollapsible mini-coresMolded capShut-offCollapsingsegments (3)Non-collapsingcenter pin blades (3)Stripper platePositive collapsesleeve (included)Core sleeve with(3) collapsingsegmentsCenter pin with (3)non-collapsingbladesEjector plateassemblyCooling hole incenter pinAlignment flats on coresleeve and center pinREFA. PartMinor Ø(min.)B. PartMajor Ø(max.)C. Maximumpartundercutat LD. MaximumpartdepthE. Lengthof fittedsurfaceon coreF. Pin protrusion,min.G. Insidediametercollapsedcore nomH. Pindiameterat face(nominal)K. Stripperbushingshut-offJ. Width ofnon-collapsingR. Pin tipradiusS. MaterialshrinkageCCM 0001 10,80-S 16,38-SCCM 0002 14,22-S 20,45-SCCM 0003 18,03-S 24,51-S1,30-(0,02L+0,5S)1,45-(0,02L+0,5S)1,50-(0,02L+0,5S)21,60-S1-K 21,60 0,4 (0,8 max) 2,30 7,60 4,00 4 0,2021,60-S1-K 21,60 0,4 (0,8 max) 4,60 10,70 4,83 4 0,2025,40-S1-K 25,40 0,4 (0,8 max) 7,90 14,20 5,08 4 0,20S= Shrinkagefactor (%)x Part diameter(mm)S1= Shrinkagefactor (%)x Part length(mm)
Page 1: Collapsible CoreD-M-E Europe 04/02/
Page 6: Info CCM-CCContact us for more info

Collapsible Core - DME

Create successful ePaper yourself

Delete template?

Save as template?