CERTI-VEX AC25 - Vexcon Chemicals

SECOND COATAfter application of the first coat a second coat may beapplied when the surface has dried. Apply second coat at 400-500 sq.ft. /gal (10-12.5 m 2 /L).MAINTENANCESpills should be removed promptly and cleaned with a highquality commercial detergent. Floors should be cleanedregularly. Periodic reapplication may be required as the sealerwears off.TOPCOATS AND ADHESIVESCerti-Vex AC25 cured concrete can be topcoated with avariety of paint, adhesives and mastics, a minimum of 28 daysafter application. It is strongly suggested that a test area beapplied prior to coating the entire surface, since products canadhere to concrete in varying degrees. Concrete cured withCerti-Vex AC25 is typically topcoated without incident,however, it is advisable to check with the manufacturer of thetopcoat for any precautionary information.SPECIFICATIONS/COMPLIANCE• ASTM C 1315 Type 1, Class B• AASHTO M-148• ASTM C 309 Type 1 Class A&B• Federal specification TTC0800A (GSA FSS) Type 1.• USDA, ADA and ASTM 2047 non-slip• Passes 500 hours weatherometer resistance as measured byASTM G53Test reports are available upon request.SPECIAL NOTES• To assist in application 200 sq.ft. /gal wet film isapproximately equal to the thickness of a sheet of paper• Will tend to show rubber burns or tire marks• Will cause bleeding of bituminous surfaces• May cause mottling of colored surfaces• Not gasoline resistant. Use Vexcon Powercoat ® GR• Application of more than two coats is not recommended• Over application may lead to surface discoloration andimproper sealer performance.• Mix well before use.• Keep from freezing.• Do not apply more material per square foot thanspecified.• Can apply when surface temperatures are 20° F - 85° F,when below or above these ranges review Vexcon's Coldand Hot Weather Application Guides.• If properly stored in its original sealed container, threeyears from date of manufacture.Rotate your stock.• For use by experienced professionally trained applicatorsPACKAGINGCerti-Vex AC 25 is available in 55-gallon drums and 5-gallonpails. Contact Vexcon directly to discuss your customizedpackaging requirements.VITAL STATISTICS• Flash Point (TCC):106º F (41ºC)• Boiling Point (706 mmHg): 310-403 F (154-207ºC)• Autoignition Temp:Above 473º F (245ºC)• Extinguishing Media: Foams, Dry Chemical, C02,• Water may be used to reduce the rate of burning and forcooling containers.PHYSICAL PROPERTIES• Wet appearance Water White• Dry appearance Clear• Dry to touch 45 minutes• Dry - tack free 85 minutes• Foot traffic 24 hours• Vehicle traffic 72 hours• Solids 25% minimumNote: All calculations based upon 68-77° F (20-25° c).Lower temperatures and relative humidity will extend drytimes.HEALTH AND SAFETY• Use only with adequate ventilation.• Use of gloves, goggles and other protective clothing isadvised when using this product.• If swallowed, do not induce vomiting.• Use of respirators is advised when using in confinedareas.Vexcon MSDS #CS119 is an integral part of the safety andapplication of our product. A short synopsis is provided in thisproduct data sheet. Before using this Vexcon product, it isadvisable to obtain a copy of the MSDS from your distributoror by contacting Vexcon Chemicals.CONTACT US @Additional product information, technical assistance andcustomer service is available by contacting Vexcon Chemicalsdirectly or our distributors.• www.vexcon.com• Technicalservice@vexcon.com• Customerservice@vexcon.com• Sales@vexcon.com• Voice: 888.839.2661• Fax: 215.332.9997